Harbor Freight 14 In Oscillating Spindle Sander Product Manual
Manual for the 69257 14 Oscillating Spindle Sander 69257 14 In. Oscillating Spindle Sander
2015-05-27
: Harbor-Freight Harbor-Freight-14-In-Oscillating-Spindle-Sander-Product-Manual-723168 harbor-freight-14-in-oscillating-spindle-sander-product-manual-723168 harbor-freight pdf
Open the PDF directly: View PDF 
.
Page Count: 12
Page 2 For technical questions, please call 1-800-444-3353. Item 69257
Table of Contents
Safety ......................................................... 3
Specifications ............................................. 6
Setup .......................................................... 6
Operation .................................................... 7
Maintenance ............................................... 8
Parts List and Diagram .............................. 10
Warranty .................................................... 12
WARNING SYMBOLS AND DEFINITIONS
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Addresses practices not related to personal injury.
SAFETY OPERATION MAINTENANCESETUP
Page 3For technical questions, please call 1-800-444-3353.Item 69257
IMPORTANT SAFETY INFORMATION
General Tool Safety Warnings
Read all safety warnings and instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
1. KEEP GUARDS IN PLACE and in working order.
2. REMOVE ADJUSTING KEYS AND WRENCHES.
Form habit of checking to see that keys and adjusting
wrenches are removed from tool before turning it on.
3. KEEP WORK AREA CLEAN.
Cluttered areas and benches invite accidents.
4. DON’T USE IN DANGEROUS ENVIRONMENT.
Don’t use power tools in damp or wet locations,
or expose them to rain. Keep work area well lighted.
5. KEEP CHILDREN AWAY. All visitors should
be kept safe distance from work area.
6. MAKE WORKSHOP KID PROOF with padlocks,
master switches, or by removing starter keys.
7. DON’T FORCE TOOL. It will do the job better
and safer at the rate for which it was designed.
8. USE RIGHT TOOL. Don’t force tool or attachment
to do a job for which it was not designed.
Table A: RECOMMENDED MINIMUM WIRE GAUGE
FOR EXTENSION CORDS
(120 VOLT)
NAMEPLATE
AMPERES
(at full load)
EXTENSION CORD
LENGTH
25′ 50′ 100′ 150′
0 – 6 18 16 16 14
6.1 – 10 18 16 14 12
10.1 – 12 16 16 14 12
12.1 – 16 14 12 Do not use.
9. USE PROPER EXTENSION CORD. Make sure your
extension cord is in good condition. When using
an extension cord, be sure to use one heavy
enough to carry the current your product will
draw. An undersized cord will cause a drop in line
voltage resulting in loss of power and overheating.
Table A shows the correct size to use depending
on cord length and nameplate ampere rating.
If in doubt, use the next heavier gauge.
The smaller the gauge number, the heavier the cord.
10. WEAR PROPER APPAREL. Do not wear
loose clothing, gloves, neckties, rings, bracelets,
or other jewelry which may get caught in moving
parts. Nonslip footwear is recommended.
Wear protective hair covering to contain long hair.
11. ALWAYS USE SAFETY GLASSES. Also use
face or dust mask if cutting operation is dusty.
Everyday eyeglasses only have impact resistant
lenses, they are NOT safety glasses.
12. DON’T OVERREACH. Keep proper
footing and balance at all times.
13. MAINTAIN TOOLS WITH CARE. Keep tools sharp
and clean for best and safest performance. Follow
instructions for lubricating and changing accessories.
14. DISCONNECT TOOLS before servicing;
when changing accessories, such as
blades, bits, cutters, and the like.
15. REDUCE THE RISK OF UNINTENTIONAL
STARTING. Make sure switch is in
off position before plugging in.
16. USE RECOMMENDED ACCESSORIES.
Consult the owner’s manual for recommended
accessories. The use of improper accessories
may cause risk of injury to persons.
17. NEVER STAND ON TOOL. Serious injury
could occur if the tool is tipped or if the
cutting tool is unintentionally contacted.
18. CHECK DAMAGED PARTS. Before further use
of the tool, a guard or other part that is damaged
should be carefully checked to determine that
it will operate properly and perform its intended
function – check for alignment of moving parts,
binding of moving parts, breakage of parts,
mounting, and any other conditions that may
affect its operation. A guard or other part that is
damaged should be properly repaired or replaced.
19. NEVER LEAVE TOOL RUNNING UNATTENDED.
TURN POWER OFF. Don’t leave tool
until it comes to a complete stop.
SAFETYOPERATIONMAINTENANCE SETUP
Page 4 For technical questions, please call 1-800-444-3353. Item 69257
Grounding Instructions
TO PREVENT ELECTRIC SHOCK AND DEATH FROM INCORRECT GROUNDING WIRE CONNECTION
READ AND FOLLOW THESE INSTRUCTIONS:
110-120 V~ Grounded Tools: Tools with Three Prong Plugs
1. In the event of a malfunction or breakdown,
grounding provides a path of least resistance for
electric current to reduce the risk of electric shock.
This tool is equipped with an electric cord having an
equipment-grounding conductor and a grounding
plug. The plug must be plugged into a matching
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
2. Do not modify the plug provided – if it will
not fit the outlet, have the proper outlet
installed by a qualified electrician.
3. Improper connection of the equipment-grounding
conductor can result in a risk of electric shock.
The conductor with insulation having an outer
surface that is green with or without yellow
stripes is the equipment-grounding conductor.
If repair or replacement of the electric cord or
plug is necessary, do not connect the equipment-
grounding conductor to a live terminal.
4. Check with a qualified electrician or service
personnel if the grounding instructions are
not completely understood, or if in doubt as
to whether the tool is properly grounded.
5. Use only 3-wire extension cords that
have 3-prong grounding plugs and 3-pole
receptacles that accept the tool’s plug.
6. Repair or replace damaged or worn cord immediately.
125 V~ 3-Prong Plug and Outlet
(for up to 125 V~ and up to 15 A)
Grounding
Pin
7. This tool is intended for use on a circuit that has
an outlet that looks like the one illustrated above in
125 V~ 3-Prong Plug and Outlet. The tool has a
grounding plug
that looks like the plug illustrated above
in 125 V~ 3-Prong Plug and Outlet.
8. The outlet must be properly installed and grounded
in accordance with all codes and ordinances.
9. Do not use an adapter to connect
this tool to a different outlet.
Sander Safety Warnings
1. Wear eye protection.
2. Do not wear gloves, necktie, or loose clothing.
3. Support workpiece with worktable.
4. The worktable is the surface mounted close to
the sanding surface that the operator rests the
workpiece against to prevent it from being pulled
by the sanding surface. For safety, use the
worktable insert that matches the sanding sleeve.
5. The use of accessories or attachments not
recommended by the manufacturer may
result in a risk of injury to persons.
6. When servicing use only identical replacement parts.
7. Only use safety equipment that has been approved
by an appropriate standards agency. Unapproved
safety equipment may not provide adequate
protection. Eye protection must be ANSI-approved
and breathing protection must be NIOSH-approved
for the specific hazards in the work area.
8. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or medication.
A moment of inattention while operating power
tools may result in serious personal injury.
9. Industrial applications must follow OSHA guidelines.
10. Maintain labels and nameplates on the tool.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.
SAFETY OPERATION MAINTENANCESETUP
Page 5For technical questions, please call 1-800-444-3353.Item 69257
11. Avoid unintentional starting.
Prepare to begin work before turning on the tool.
12. People with pacemakers should consult their
physician(s) before use. Electromagnetic fields in
close proximity to heart pacemaker could cause
pacemaker interference or pacemaker failure.
13. WARNING: Some dust created by power
sanding, sawing, grinding, drilling, and other
construction activities, contains chemicals
known [to the State of California] to cause
cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks and cement or other
masonry products
• Arsenic and chromium from
chemically treated lumber
Your risk from these exposures varies,
depending on how often you do this type of work.
To reduce your exposure to these chemicals:
work in a well ventilated area, and
work with approved safety equipment, such
as those dust masks that are specially
designed to filter out microscopic particles.
(California Health & Safety Code § 25249.5, et seq.)
14. WARNING: Handling the cord on this product will
expose you to lead, a chemical known to the State
of California to cause cancer, and birth defects or
other reproductive harm. Wash hands after handling.
(California Health & Safety Code § 25249.5, et seq.)
15. The warnings, precautions, and instructions
discussed in this instruction manual cannot
cover all possible conditions and situations
that may occur. It must be understood by the
operator that common sense and caution are
factors which cannot be built into this product,
but must be supplied by the operator.
Vibration Safety
This tool vibrates during use. Repeated or long-term
exposure to vibration may cause temporary or permanent
physical injury, particularly to the hands, arms and
shoulders. To reduce the risk of vibration-related injury:
1. Anyone using vibrating tools regularly or for an
extended period should first be examined by a
doctor and then have regular medical check-ups
to ensure medical problems are not being caused
or worsened from use. Pregnant women or
people who have impaired blood circulation to
the hand, past hand injuries, nervous system
disorders, diabetes, or Raynaud’s Disease should
not use this tool. If you feel any medical or
physical symptoms related to vibration (such as
tingling, numbness, and white or blue fingers),
seek medical advice as soon as possible.
2. Do not smoke during use. Nicotine reduces
the blood supply to the hands and fingers,
increasing the risk of vibration-related injury.
3. Use tools with the lowest vibration when there
is a choice between different processes.
4. Include vibration-free periods each day of work.
5. Grip tool as lightly as possible (while still keeping
safe control of it). Let the tool do the work.
6. To reduce vibration, maintain the tool as
explained in this manual. If any abnormal
vibration occurs, stop use immediately.
SAVE THESE INSTRUCTIONS.
Sander Safety Warnings (cont.)
SAFETYOPERATIONMAINTENANCE SETUP
Page 6 For technical questions, please call 1-800-444-3353. Item 69257
Specifications
Electrical Rating 120V~ / 60Hz / 2.6A
Motor No Load Speed 1725 RPM
Speed 30 OPM
Stroke 5/8"
Table Top 14" diameter
Setup - Before Use:
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Turn the Power Switch of the tool off and unplug the tool from its electrical
outlet before performing any procedure in this section.
Note: For additional information regarding the parts listed in the following pages,
refer to the Assembly Diagram near the end of this manual.
Mounting Sander
1. Select a mounting location that is able to
support the weight of the Sander, plus any
additional weight placed on it during use.
2. Make sure there are no hidden electric wires,
cables or other obstructions that may interfere
with the mounting procedure or cause a hazard.
3. Mark the mounting hole locations and
drill the appropriate size holes for the
mounting bolts (not included).
4. Mount the Sander using Bolts, washers
and nuts (not included).
Installing Dust Collector
Attach a dust collection system (not included) to the dust port.
Functions
Figure A
Spindle
Knob
Sanding Sleeve
Sanding Drum
Table Insert
Table Top
Power Switch
Safety Key
Dust Port
Accessories
1/2" 3/4" 1" 1½" 2" 3"
Drum
Washer
Spindle
Drum
Sanding
Sleeve
Table
Insert
1/2"
3/4"
1"
1½"
2"
3"
Call
1-800-444-3353
to order sleeves as
replacement parts.
3092372
SAFETY OPERATION MAINTENANCESETUP
Page 7For technical questions, please call 1-800-444-3353.Item 69257
Operating Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
Tool Set Up - Installing Sanding Sleeves
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Turn the Power Switch of the tool off and unplug the tool from its electrical
outlet before performing any procedure in this section.
TO PREVENT SERIOUS INJURY:
DO NOT OPERATE WITH ANY GUARD DISABLED, DAMAGED, OR REMOVED.
Note: Call 1-800-444-3353 to order
sleeves as replacement parts.
Note: Do not mix component sizes. For instance,
only use the 3/4" Sanding Sleeve with the 3/4" Drum
Washer, 3/4" Spindle Drum and 3/4" Table Insert.
Note: The 1/2″ Sanding Sleeve does not have a matching
Drum Washer or Spindle Drum. It slides directly onto
the Spindle, and is held in place with the Knob.
1. Select the desired size Sanding Sleeve and matching
Table Insert, Rubber Drum and Drum Washer.
2. Insert the matching Table Insert into the Table top with
the directional arrows facing in a clockwise direction.
3. Unthread the Knob on the top of the Spindle.
Note: The Knob unthreads clockwise
and tightens counterclockwise.
4. If using the Smallest size Sanding Sleeve (1/2") slide
the Sanding Sleeve over the Spindle. If using any
other size Sanding Sleeve, slide it over the same size
Rubber Drum then slide the drum onto the Spindle.
5. If using the Smallest size Sanding Sleeve (1/2")
thread the Knob onto the Spindle. If using any
other size Sanding Sleeve, slide the same size
Drum Washer onto the Spindle, then thread
the Knob onto the top of the Spindle.
Workpiece and Work Area Set Up
1. Designate a work area that is clean and well-lit.
The work area must not allow access by children
or pets to prevent distraction and injury.
2. Route the power cord along a safe route to reach
the work area without creating a tripping hazard or
exposing the power cord to possible damage. The
power cord must reach the work area with enough
extra length to allow free movement while working.
3. There must not be objects, such as utility lines,
nearby that will present a hazard while working.
General Operating Instructions
1. Install the desired sanding sleeve.
2. Plug the Power Cord into a grounded 120V outlet.
3. Insert the Safety Key and turn the Power Switch on.
WARNING! FOR DRY SANDING ONLY. Do not use
water or another lubricant with this sander. Wet sanding
will damage the machine and present a shock hazard.
4. Contact the workpiece with minimal pressure.
5. Keep the piece moving steadily and
smoothly across the sanding surface
until the desired finish is achieved.
6. When finished, turn the Power Switch
off and remove the Safety Key.
7. To prevent accidents, turn off the tool,
remove its safety key and disconnect its
power supply after use. Clean, then store
the tool indoors out of children’s reach.
SAFETYOPERATIONMAINTENANCE SETUP
Page 8 For technical questions, please call 1-800-444-3353. Item 69257
Maintenance and Servicing
Procedures not specifically explained in this manual must
be performed only by a qualified technician.
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Turn the Power Switch of the tool off and unplug the tool from its electrical
outlet before performing any procedure in this section.
TO PREVENT SERIOUS INJURY FROM TOOL FAILURE:
Do not use damaged equipment. If abnormal noise or vibration
occurs, have the problem corrected before further use.
Cleaning, Maintenance, and Lubrication
1. BEFORE EACH USE, inspect the general
condition of the tool. Check for:
• loose hardware,
• misalignment or binding of moving parts,
• cracked or broken parts,
• damaged electrical wiring, and
• any other condition that may
affect its safe operation.
2. AFTER USE, wipe external surfaces
of the tool with clean cloth.
3. WARNING! If the supply cord of this
power tool is damaged, it must be replaced
only by a qualified service technician.
SAFETY OPERATION MAINTENANCESETUP
Page 9For technical questions, please call 1-800-444-3353.Item 69257
Troubleshooting
Problem Possible Causes Likely Solutions
Tool will not start. 1. Cord not connected.
2. No power at outlet.
3. Tool’s thermal reset breaker
tripped (if equipped).
4. Internal damage or wear. (Carbon
brushes or switch, for example.)
1. Check that cord is plugged in.
2. Check power at outlet. If outlet is unpowered,
turn off tool and check circuit breaker.
If breaker is tripped, make sure circuit is right
capacity for tool and circuit has no other loads.
3. Turn off tool and allow to cool.
Press reset button on tool.
4. Have technician service tool.
Tool operates
slowly.
Extension cord too long or
wire size too small.
Eliminate use of extension cord. If an extension cord
is needed, use one with the proper diameter for its
length and load. See Table A on page 3.
Performance
decreases
over time.
1. Accessory dull or damaged.
2. Carbon brushes worn or damaged.
1. Keep cutting accessories sharp. Replace as needed.
2. Have qualified technician replace brushes.
Excessive noise
or rattling.
1. Internal damage or wear. (Carbon
brushes or bearings, for example.)
2. Sanding Sleeve and/
or Drum not secure.
1. Have technician service tool.
2. Check that Sanding Sleeve and Drum
are secured in place with the Knob.
Overheating. 1. Forcing machine to work too fast.
2. Blocked motor housing vents.
3. Motor being strained by long or
small diameter extension cord.
1. Allow machine to work at its own rate.
2. Wear ANSI-approved safety goggles and
NIOSH-approved dust mask/respirator while
blowing dust out of motor using compressed air.
3. Eliminate use of extension cord. If an extension cord
is needed, use one with the proper diameter for
its length and load. See Table A on page 3.
Sanding Sleeve
slips on Drum.
1. Too much pressure on
Sanding Sleeve.
2. Spindle Knob loose.
3. Starting machine with
workpiece contacting sleeve.
4. Mismatched sleeve,
drum or washer.
1. Apply light pressure. Do not press hard
on the Spindle while sanding.
2. Check that spindle Knob is secure.
3. Allow sleeve to come up to full speed
before contacting workpiece.
4. Check that the sleeve, drum and
washer are the same size.
Material not
affected from
sanding.
Sanding Sleeve is dull, glazed
or loaded with sawdust.
Replace Sanding Sleeve.
Wood burns
appearing
on wood.
Sanding Sleeve glazed or
loaded with sawdust.
Replace Sanding Sleeve.
Spindle does not
fully oscillate.
1. Sawdust build up.
2. Mechanical issue.
1. Turn off and unplug the Sander then
clean all sawdust from machine.
2. Have serviced by a qualified technician.
Follow all safety precautions whenever diagnosing or servicing
the tool. Disconnect power supply before service.
Call
1-800-444-3353
to order sleeves as
replacement parts.
SAFETYOPERATIONMAINTENANCE SETUP
Page 10 For technical questions, please call 1-800-444-3353. Item 69257
Part Description Qty
1 Knob 1
2
Drum Washer Set (5 pieces)
a 3/4" dia. 1
b 1" dia. 1
c 1-1/2" dia. 1
d 2" dia. 1
e 3" dia. 1
3
Sanding Sleeve Set (6 pieces)
a 1/2" dia. 1
b 3/4" dia. 1
c 1" dia. 1
d 1-1/2" dia. 1
e 2" dia. 1
f 3" dia. 1
4
Rubber Drum Set (5 pieces)
a 3/4" dia. 1
b 1" dia. 1
c 1-1/2" dia. 1
d 2" dia. 1
e 3" dia. 1
5
Table Insert Set (6 pieces)
a 1/2" dia. 1
b 3/4" dia. 1
c 1" dia. 1
d 1-1/2" dia. 1
e 2" dia. 1
f 3" dia. 1
6 Table 1
7 Fan 1
8 Hex Sunk Screw M5x10 2
9 Dust Port 1
10 Flat Washer Ф5 6
11 Hex Socket Head Bolt M5×12 6
Part Description Qty
12 Seal Ф16×Ф30×2.5 1
13 Bearing 6003-2Z 1
14 Top Bearing Bracket 1
15 Shaft 1
16 Key 5x5x20L 1
16.1 Circlip For Shaft Ø17 2
17 Flange Bevel Gear 1
18 Set Screw M5x6L 1
19 Bearing 6001-2Z 2
20 Gear Shaft 1
21 Motor Stud 3
22 Flange Straight Gear 1
23 Flat Washer Ф10 3
24 Spring Washer Ф10 3
25 Hex Nut M10 3
26 Motor 1
27 Hex Pan Head Screw M5×10L 1
28 Serrated Washer Ф5.3×Ф10 1
29 Strain Relief 6P-4 2
29.1 Strain Relief 5P-4 1
30 Power Cord 1
31 Hex Socket Head Screw M6×12L 4
32 Flat Washer Ø6 4
33 Base 1
34 Switch 1
35 Switch Box 1
36 Tap Screw ST4.2×9.5-C-H 3
39 Nylon Ribbon 1
40 Circlip For Shaft Ø12 1
41 Sound Insulation Cover 2
42 Foot 4
43 Washer Ø17 x Ø26 1
Parts List and Diagram
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Parts List
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.
SAFETY OPERATION MAINTENANCESETUP
Page 11For technical questions, please call 1-800-444-3353.Item 69257
1
2
3
5
4
6
7
9
15
10
11
25
32
31
21
8
13
14
21
12
21
27
28
26
30
36
35
29
23
24
37
16
19
20
17
19
22
33
40
18
29.1
41
41
39
16.1
16.1
34
42
43
Assembly Diagram
SAFETYOPERATIONMAINTENANCE SETUP
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
