Harbor Freight 14 Piece Hydraulic Punch Driver Kit Product Manual
Manual for the 96718 14 Piece Hydraulic Punch Driver Kit 96718 Hydraulic Punch Driver w/ 5 Hydraulic Punches & Dies
2015-05-27
: Harbor-Freight Harbor-Freight-14-Piece-Hydraulic-Punch-Driver-Kit-Product-Manual-723453 harbor-freight-14-piece-hydraulic-punch-driver-kit-product-manual-723453 harbor-freight pdf
Open the PDF directly: View PDF 
.
Page Count: 8
Hydraulic Punch
Driver Kit
Item 96718
INSTRUCTIONS AND
PRECAUTIONS
Visit our website at:
http://www.harborfreight.com
Read this material before
using this product.
Failure to do so can result
in serious injury.
SAVE THIS MANUAL.
When unpacking, make sure
that the product is intact and
undamaged.
If any parts are missing or broken,
please call 1-800-444-3353
as soon as possible.
Copyright© 2007 by Harbor Freight Tools®.
All rights reserved. No portion of this document
or any artwork contained herein may be
reproduced in any shape or form without the
express written consent of Harbor Freight
Tools. Diagrams within this document may
not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly
from the product described herein. Tools required
for assembly and service may not be included.
For technical questions or replacement
parts, please call 1-800-444-3353.
Manual Revised 12d
Page 2 For technical questions, please call 1-800-444-3353. SKU 96718
Specications
Maximum
Capacity
11 Gauge (for mild carbon steel)
16 Gauge (for stainless steel)
Punching
Force 10 Ton (20,000 lb.)
Important Safety Information
1. Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
2. Keep children and bystanders
away while operating the Punch
Driver Kit. Distractions can
cause you to lose control.
3. Stay alert, watch what you are
doing and use common sense
when operating the Punch Driver
Kit. Do not use the Punch Driver
Kit while you are tired or under
the inuence of drugs, alcohol or
medication. A moment of inattention
while operating hydraulic tools may
result in serious personal injury.
4. Use safety equipment. Always wear
eye protection. Safety equipment
such as dust mask, non-skid safety
shoes, hard hat, or hearing protection
used for appropriate conditions
will reduce personal injuries.
5. Dress properly. Do not wear loose
clothing or jewelry. Keep your hair,
clothing and gloves away from moving
parts. Loose clothes, jewelry or long
hair can be caught in moving parts.
6. Do not force the Hydraulic Punch
Driver Kit. Use the correct tool for
your application. The correct tool
will do the job better and safer at
the rate for which it was designed.
7. Store idle tool out of the reach of
children and do not allow persons
unfamiliar with the Hydraulic Punch
Driver Kit or these instructions
to operate the Hydraulic Punch
Driver Kit. This tool is dangerous
in the hands of untrained users.
8. Maintain tool. Check for misalignment
or binding of moving parts, breakage
of parts and any other condition that
may affect the Hydraulic Punch Driver
Kit’s operation. If damaged, have the
Hydraulic Punch Driver Kit repaired
before use. Many accidents are caused
by poorly maintained power tools.
9. Keep cutting tools sharp and clean.
Properly maintained cutting tools with
sharp cutting edges are less likely
to bind and are easier to control.
10. Have Hydraulic Punch Driver Kit
serviced by qualied service technician
using only identical replacement parts.
This will ensure the safety of Hydraulic
Punch Driver Kit is maintained.
11. Maintain product labels and
nameplates. These carry important
safety information. If unreadable
or missing, contact Harbor Freight
Tools for a replacement.
12. This product is not a toy.
Keep it out of reach of children.
13. WARNING! Some dust created by
power sanding, sawing, grinding,
drilling, and other construction
activities, contains chemicals
known to the State of California to
cause cancer, birth defects or other
reproductive harm. (California Health
& Safety Code § 25249.5, et seq.)
Page 3For technical questions, please call 1-800-444-3353.SKU 96718
14. The warnings, precautions, and
instructions discussed in this instruction
manual cannot cover all possible
conditions and situations that may
occur. It must be understood by the
operator that common sense and
caution are factors which cannot
be built into this product, but must
be supplied by the operator.
Operating Instructions
Read the ENTIRE IMPORTANT
SAFETY INFORMATION
section at the beginning of
this document including all
text under subheadings
therein before set up or use of
this product.
1. Bleed air from Hydraulic System
before rst use. See page 4.
2. When selecting a work piece, please
do not exceed the Maximum Cutting
Capacity of 0.12” for mild carbon
steel and 0.08” for stainless steel.
Threaded Stud (13/14)
Punch (2-6)
Punch Head
(16)
Adapter (12)
Die
(7-11)
Work Piece
Figure 1
3. Practice with a scrap work piece
before using the actual work piece.
Working with a scrap work piece
will help you familiarize yourself
with the Punch Driver Kit.
4. Select the size of the Threaded Stud
(13, 14) to be used, either 3/4” or 7/16”.
5. Select the size of the Punch and Die
to be used (see Parts List on page 6).
6. Plan and measure the location
of the hole to be punched in the
work piece. This hole must t the
Threaded Stud to be used.
7. Drill a lead hole at the center
point of the hole marked and
measured in step 5.
8. The 7/16” Threaded Stud is to be
used with Punch (2) and Die (7).
9. Thread the Threaded Stud into the
Punch Head (16). Note that the end
with the shorter threads is threaded
into the Punch Head. See Figure 1.
10. The Adapter (12) is to be used with
all Punch and Dies that are used.
11. Slide Adapter and then Die
onto the Threaded Stud.
12. Slide your work piece with
the drilled hole down onto the
Die, as shown in Figure 1.
13. Thread the Punch down onto the
work piece as tightly as possible.
14. Turn the Release Valve (18)
(see Figure 2) to the “ON” position.
Figure 2
Release
Valve (18)
Page 4 For technical questions, please call 1-800-444-3353. SKU 96718
15. Grasp the Pump Handle (17) and
pump it up and down until the Punch
has punched through the work piece.
16. Turn the Release Valve (18)
to the “OFF” position.
17. Thread off the Punch, remove
the work piece, the Die and the
Adapter. Remove the Threaded
Stud from the Punch Head.
18. Carefully remove the punched
material and its residue.
19. Clean, then set the Punch Driver Kit
into its Carrying Case and store the
tool indoors out of children’s reach.
Maintenance and Servicing
1. BEFORE EACH USE, inspect the
general condition of the Hydraulic
Punch Driver Kit. Check for loose
attachments, binding of moving parts,
cracked or broken attachments,
and any other condition that may
affect its safe operation. If any
abnormality is found, have the
problem corrected before further use.
Do not use damaged equipment.
2. AFTER EACH USE, wipe off Punch
Driver Kit with clean, moist cloth.
3. Service to the Punch Driver
Kit should only be done by a
qualied Service Technician.
Bleeding Instructions
1. NOTE: During shipment and handling,
air may get trapped in the hydraulic
system-Hydraulic Pump with Pressure
Hose. This can interfere with the
performance of the Punch Driver Kit.
Bleed air from the hydraulic system
according to the following instructions.
2. Open the Release Valve, making sure
the Punch Head is fully extended, and
unscrew the coupler to disconnect the
Hose from the Punch Head. Close
the Release Valve, press down the
core rod in the Hose Coupler.
3. Pump the Pump Handle.
Release the Hose Coupler until
oil ows out of the Hose.
4. Attach the Hose to the Punch Head.
5. Open Release Valve, and Pump Handle
several times in rapid succession.
Repeat this procedure until the Punch
Driver Kit is working properly.
Troubleshooting
PROBLEM POSSIBLE CAUSES PROBABLE SOLUTIONS
Handle stroke only
partly effective.
Air in pump chamber. Follow the Bleeding
Instructions above.
Handle raises on its own. Sticking or leaking
Release Valve.
Remove and clean
the Release Valve.
Handle snaps back. Sticking Delivery Valve. Open Release Valve.
Pump rapidly several
times. Close Valve.
Page 5For technical questions, please call 1-800-444-3353.SKU 96718
Punch Sizes/Pipe, Conduit, Metal Tubing
Outside Diameter Specications Chart
Punch Pipe / O.D. Conduit O.D.
Intermediate
Thin Wall O.D. Electrical Metal
Tubing O.D.
1.115” 3/4” / 1.505” 1.029” 0.922” 0.922”
1.362” 1” / 1.315” 1.29" 1.163" 1.163"
1-11/16” (1.687”) 1-1/4” / 1.660” 1.638" 1.51" 1.570"
1-15/16” (1.937”) 1-1/2” / 1.900” 1.883" 1.74" 1.74"
2-3/8” (2.375”) 2” / 2.375” 2.360” 2.197” 2.197”
Pipe Tube
1.115” 3/4” 3/4”
Page 6 For technical questions, please call 1-800-444-3353. SKU 96718
Record Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
PLEASE READ THE FOLLOWING CAREFULLY
NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY
KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE
OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR
DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN
BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND
LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Part Description Qty
1Hydraulic Pump with
Pressure Hose
1
2Punch 1.115” for 3/4” Pipe 1
3Punch 1.362” for 1” Pipe 1
4Punch 1-11/16”
for 1-1/4” Pipe
1
5Punch 1-15/16”
for 1-1/2” Pipe
1
6Punch 2-3/8” for 2” Pipe 1
7Die for 1.115” Punch 1
8Die for 1.362” Punch 1
Part Description Qty
9Die for 1-11/16” Punch 1
10 Die for 1.15/16” Punch 1
11 Die for 2-3/8” Punch 1
12 Adapter 1
13 Threaded Stud 3/4” 1
14 Threaded Stud 7/16” 1
15 Carrying Case (not shown) 1
16 Punch Head 1
17 Pump Handle 1
18 Release Valve 1
Parts List
Page 7For technical questions, please call 1-800-444-3353.SKU 96718
1
18
17
13
2
16
3
4
5
6
7
8
9
10
11
12
14
Parts Diagram
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet
high quality and durability standards, and warrants to the original purchaser that
this product is free from defects in materials and workmanship for the period
of 90 days from the date of purchase. This warranty does not apply to damage
due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or
alterations outside our facilities, criminal activity, improper installation, normal
wear and tear, or to lack of maintenance. We shall in no event be liable for
death, injuries to persons or property, or for incidental, contingent, special or
consequential damages arising from the use of our product. Some states do
not allow the exclusion or limitation of incidental or consequential damages, so
the above limitation of exclusion may not apply to you. THIS WARRANTY IS
EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us
with transportation charges prepaid. Proof of purchase date and an explanation
of the complaint must accompany the merchandise. If our inspection veries
the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you
with a replacement. We will return repaired products at our expense, but if we
determine there is no defect, or that the defect resulted from causes not within
the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specic legal rights and you may also have other rights
which vary from state to state. ghghghghhhhhhhghhhhhhhhhghhhhhhgh
