Harbor Freight 2 Pc Submersible Trailer Lights Product Manual

94137 94137

: Harbor-Freight Harbor-Freight-2-Pc-Submersible-Trailer-Lights-Product-Manual-723709 harbor-freight-2-pc-submersible-trailer-lights-product-manual-723709 harbor-freight pdf

Open the PDF directly: View PDF .
Page Count: 8

Download
Open PDF In Browser	View PDF

Specifications
Power Source

12 VDC only (Negative Ground Only)

Features

2 Combination Submersible, Class A Stop, Tail, Turn Signals, License
Plate Bracket, 4 ft. Trunk Harness and 25 ft. Y-Harness.

Light Type

18 LEDs Per Light (not serviceable)

Page 2

For technical questions, please call 1-888-866-5797.

Trailer Lights

Important Safety Information

Installation Precautions
1.

Install only according to these
instructions. Improper installation
can create hazards.

2.

Wear ANSI-approved safety goggles
and heavy-duty work gloves
during installation.

3.

Keep installation area clean and well lit.

4.

Keep bystanders out of the
area during installation.

5.

Do not install when tired or when under
the influence of drugs or medication.

6.

7.

8.

Do not install this product yourself
unless you are technically competent
to do so. If necessary, have a qualified
technician install the Trailer Lights.

9.

Use the correct lights and electrical
setup for your trailer.
If the vehicle is OVER 80" wide, install
three additional Red Marker Lights*
(not included) onto the rear of the unit.

10. If the towing vehicle has rear
turn signals separated from its
stop lights, additional hardware
and installation procedures will
Read all instructions and safety
be needed. Contact a qualified
precautions in the vehicle’s manual onto
technician for guidance.
which the Trailer Lights will be installed.
Install on negative ground
12VDC systems only.

* Example additional marker light locations:
Mount the three Red Marker Lights to the rear of
the vehicle, making sure the Lights are no closer
than 6" and no farther away than 12" from each
other center to center. After mounting, use wire nut
connectors (not included) to connect all three leads
together. Then connect to the Brown wire in the back
of one Tail Light (either side) provided in this Kit.

Use Precautions
1.

This product is not a toy. Do not
allow children to play with this item.

2.

Use as intended only.

3.

Inspect before every use; do not use
if parts are loose or damaged.

Trailer Lights

4.

Maintain product labels and
nameplates. These carry
important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.

For technical questions, please call 1-888-866-5797.

Page 3

Installation Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the
beginning of this document including all text under subheadings therein
before set up or use of this product.

Towing Vehicle Installation
Note: Use the BLUE Splice Connectors to make the connections in steps 1-3.
1.

Connect the BROWN wire of the
Trunk Harness (5) to the towing
vehicle’s Running Lights wire.

3.

Connect the GREEN wire of the
Trunk Harness to the vehicle’s
Right Stop & Turn light.

2.

Connect the YELLOW wire of the
Trunk Harness to the vehicle’s
Left Stop & Turn light.

4.

Attach the WHITE GROUND wire
to the towing vehicle’s frame.

Trailer Installation
NOTE: INSTALL THE TRAILER LIGHTS ONLY AFTER
THE TRAILER IS FULLY ASSEMBLED.
1.

2.

Mount the Tail Light (1b), marked “LH”
(with the License Window on bottom),
on the left rear of the trailer with its side
marker to the outside of the trailer.
Then, mount the License Plate
Bracket (2) underneath it.

Mount the Tail Light (1a), marked “RH”
(without the License Window), on the
right rear of the trailer with its side
marker to the outside of the trailer.

Page 4

3.

Use the included Metal Frame Clips to
mount each half of the Y-Harness (3)
down each side of the trailer.
Run one YELLOW wire and
one BROWN wire down the left side
and one GREEN wire and one BROWN
wire down the right side of the trailer.

4.

Connect the YELLOW and BROWN
wires to the Left Tail Light (1b) with
the included Wire Nut Connectors.

5.

Connect the GREEN and BROWN
wires to the Right Tail Light (1a) with
the included Wire Nut Connectors.

6.

Attach the WHITE GROUND wire
to the trailer tongue or frame.

Note: These Trailer Lights depend
on a metal, grounded trailer frame.

For technical questions, please call 1-888-866-5797.

Trailer Lights

Wiring Diagram

C

C

Connect Green
wire to Vehicle
R.H. Stop & Turn

C

Connect Yellow
wire to Vehicle
L.H. Stop & Turn

Connect
White wire to
Vehicle Frame
Connect Brown
wire to Vehicle
Running Lights

Trailer
Ground
Point

Brown Wire

Splice Connector

Green Wire

White Wire

C

Yellow Wire

3 Rear Markers
( Red) Required
for Trailers
over 80’ Wide
( Not Included)

Right Tail
Light

C

Left Tail Light &
License Bracket

Window underneath to
light up license plate.

Page 5

For technical questions, please call 1-888-866-5797.

Trailer Lights

Operation
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the
beginning of this document including all text under subheadings therein
before set up or use of this product.
TO PREVENT SERIOUS INJURY OR DEATH FROM DRIVING HAZARDS:
Test operation of all lights before every use. Troubleshoot and repair wiring
properly before using. Do not use while trailer light operation does not match
vehicle light operation, if any lights do not light up, or if any lights flicker.
Park on level area away from traffic and set vehicle parking brake/chock tires.

Testing
1.

Connect the Y-Harness (3) Plug
to the Trunk Harness (4) Plug.

2.

Turn on the towing vehicle’s
headlights. The two Tail Lights
(1a and 1b) should turn on.

3.

The brighter Stop Lights should turn
on only when the vehicle’s brake
pedal is depressed, or when the
vehicle’s turn signal is activated
(ignition key must be in its “on” position).

Troubleshooting
Problem

Possible Causes

No lights light up.

1. Vehicle’s running lights off.
2. Trailer wiring harness disconnected or connection is loose.
3. Main ground wire not connected properly.

Trailer light operation does not
match vehicle light operation.

Trunk Harness not wired properly to vehicle electrical system or
Y-Harness not wired properly to trailer lights.

A specific light does not
light up or flickers.

1. Wiring to that light is loose or disconnected.

All lights flicker.

1. Trailer wiring harness connection is loose.

Vehicle’s fuse blows repeatedly.

Short circuit somewhere in wiring or lights. Diagnose to isolate
and repair the problem. Route wires carefully to avoid pinching.

2. That light is broken.
2. Main ground wire not connected properly.

Follow all safety precautions whenever diagnosing or servicing the lights.
Park on level area away from traffic and set vehicle parking brake/chock tires.

Page 6

For technical questions, please call 1-888-866-5797.

Trailer Lights

PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST
AND INSTALLATION DIAGRAM IN THIS DOCUMENT AS A REFERENCE TOOL ONLY.
NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR
WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE
ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR
EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD
BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR
HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR
ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Parts List and Diagram
Part
1a

1b
2

Description

RH Tail Light
LH Tail Light

Qty.
1

(with License Window on bottom)

License Plate Bracket

1
1

Part
3
4
5

Description

Y-Harness
Trunk Harness
Mounting Hardware

1
1
1 pkg.

1a

1b

2

Mounting Hardware
Not Shown

Record Serial Number Here:
Note: If product has no serial number,
record month and year of purchase instead.
Trailer Lights

Qty.

3&4

Note: Some parts are listed and shown
for illustration purposes only, and are not
available individually as replacement parts.

For technical questions, please call 1-888-866-5797.

Page 7

Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality
and durability standards, and warrants to the original purchaser that this product is free from
defects in materials and workmanship for the period of 90 days from the date of purchase.
This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence
or accidents, repairs or alterations outside our facilities, criminal activity, improper installation,
normal wear and tear, or to lack of maintenance. We shall in no event be liable for death,
injuries to persons or property, or for incidental, contingent, special or consequential damages
arising from the use of our product. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation of exclusion may not apply to you.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation
charges prepaid. Proof of purchase date and an explanation of the complaint must accompany
the merchandise. If our inspection verifies the defect, we will either repair or replace
the product at our election or we may elect to refund the purchase price if we cannot readily
and quickly provide you with a replacement. We will return repaired products at our expense,
but if we determine there is no defect, or that the defect resulted from causes not within
the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also
have other rights which vary from state to state.

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Create Date                     : 2013:11:13 09:09:06-08:00
Creator                         : Adobe InDesign CC (Macintosh)
Modify Date                     : 2013:11:13 09:09:36-08:00
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Instance ID                     : uuid:2aaccd99-5cd2-2644-8d33-b075388e1e7d
Original Document ID            : adobe:docid:indd:3d8405b6-7ee1-11df-9488-aa083f618b49
Document ID                     : xmp.id:4ff2b56a-ec7a-4d08-94e4-a55474705fce
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:1333dc4c-71f2-42c9-b9c8-8c9e34f86159
Derived From Document ID        : xmp.did:13fb5de8-4068-4617-a645-32610ec68478
Derived From Original Document ID: adobe:docid:indd:3d8405b6-7ee1-11df-9488-aa083f618b49
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC (Macintosh)
History Changed                 : /
History When                    : 2013:11:13 09:09:06-08:00
Metadata Date                   : 2013:11:13 09:09:36-08:00
Creator Tool                    : Adobe InDesign CC (Macintosh)
Format                          : application/pdf
Producer                        : Adobe PDF Library 10.0.1
Trapped                         : False
Page Count                      : 8

EXIF Metadata provided by EXIF.tools