Harbor Freight 2 Ton Aluminum Racing Floor Jack With Rapidpump Product Manual

Harbor-Freight-3-Ton-Aluminum-Racing-Floor-Jack-With-Rapidpump-Product-Manual-723549 harbor-freight-3-ton-aluminum-racing-floor-jack-with-rapidpump-product-manual-723549

: Harbor-Freight Harbor-Freight-2-Ton-Aluminum-Racing-Floor-Jack-With-Rapidpump-Product-Manual-723547 harbor-freight-2-ton-aluminum-racing-floor-jack-with-rapidpump-product-manual-723547 harbor-freight pdf

Open the PDF directly: View PDF .
Page Count: 8

Visit our website at: http://www.harborfreight.com

Email our technical support at: productsupport@harborfreight.com

Item 61406 shown.

Item 62457 61406 61386

Weight Capacity 2 Tons (4,000 lb.) 2 Tons (4,000 lb.) 3 Tons (6,000 lb.)

Maximum Height 16-3/8" 18-1/2" 19-1/4"

Minimum Height 3-3/8" 3-1/4" 3-3/4"

Meets 2005 ANSI/ASME PALD standards.

REV 14h

Owner’s Manual & Safety Instructions

Save This Manual Keep this manual for the safety warnings and precautions, assembly,

operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the

back of the manual near the assembly diagram (or month and year of purchase if product has no number).

Keep this manual and the receipt in a safe and dry place for future reference.

When unpacking, make sure that the product is intact

and undamaged. If any parts are missing or broken,

please call 1-888-866-5797 as soon as possible.

Copyright© 2013 by Harbor Freight Tools®. All rights reserved.

No portion of this manual or any artwork contained herein may be reproduced in

any shape or form without the express written consent of Harbor Freight Tools.

Diagrams within this manual may not be drawn proportionally. Due to continuing

improvements, actual product may differ slightly from the product described herein.

Tools required for assembly and service may not be included.

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

Page 2 For technical questions, please call 1-888-866-5797. Item 61386 61406 62457

WARNING SYMBOLS AND DEFINITIONS

This is the safety alert symbol. It is used to alert you to potential

personal injury hazards. Obey all safety messages that

follow this symbol to avoid possible injury or death.

Indicates a hazardous situation which, if not avoided,

will result in death or serious injury.

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

Addresses practices not related to personal injury.

IMPORTANT SAFETY INFORMATION

Floor Jack Safety Warnings

1. Study, understand, and follow all instructions

before operating this device.

2. Do not exceed rated capacity.

3. Use only on hard, level surfaces.

4. Lifting device only. Immediately after lifting,

support the vehicle with appropriate means.

5. Do not move or dolly the vehicle while on the jack.

6. Failure to heed these markings may result in

personal injury and/or property damage.

7. Lift only areas of the vehicle as specified

by the vehicle manufacturer.

8. No alterations shall be made to this product.

9. Never work on, under or around a load

supported only by this device.

10. Do not adjust safety valve.

11. Wear ANSI-approved safety goggles and

heavy-duty work gloves during use.

12. Keep clear of load while lifting and lowering.

13. Lower load slowly.

14. Apply parking brake and chock

tires before lifting vehicle.

15. Lift vehicle only at manufacturer

recommended locations.

16. Inspect before every use; do not use

if parts are loose or damaged.

17. Do not use for aircraft purposes.

18. The warnings, precautions, and instructions

discussed in this manual cannot cover all

possible conditions and situations that may occur.

The operator must understand that common sense

and caution are factors, which cannot be built into

this product, but must be supplied by the operator.

19. WARNING: The brass components of this product

contain lead, a chemical known to the State

of California to cause cancer and birth defects

or other reproductive harm. (California Health

& Safety Code § 25249.5, et seq.)

20. WARNING: This product contains di (2-ethylhexyl)

phthalate (DEHP), a chemical known to the State

of California to cause cancer and birth defects

or other reproductive harm. (California Health

& Safety Code § 25249.5, et seq.)

IMPORTANT! Before first use:

Check hydraulic oil level and fill to 1/4″ below

the fill port as needed as stated on page 3.

Thoroughly test the Jack for proper operation.

If it does not work properly, bleed air from its

hydraulic system as stated on page 3.

SAVE THESE INSTRUCTIONS.

Page 3For technical questions, please call 1-888-866-5797.Item 61386 61406 62457

Setup - Before Use:

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this

manual including all text under subheadings therein before set up or use of this product.

Note: For additional information regarding the parts listed in the following pages,

refer to Parts Lists and Assembly Diagrams on page 6.

Attaching the Handle

CAUTION! The Handle may contain a spring under tension. Wear ANSI-approved safety goggles

before loosening or removing Handle. Remove Handle carefully.

1. Fasten the Upper Handle to the Lower Handle.

2. Loosen the Set Screw and insert the

assembled Handle into the Handle Socket.

3. Tighten the Set Screw.

Bleeding

1. Loosen the Fill Screw.

2. Turn the Handle counterclockwise

to open the Release Valve.

3. Pump the Handle up and down quickly several

times to purge air from the system.

4. Tighten the Fill Screw.

Adding Oil

1. Remove Fill Screw, see Figure B: Hydraulic Unit.

2. For model 61406/62457 only: Remove Screw also.

3. Add high grade hydraulic fluid into the Fill Screw

slowly until the oil reaches the top of the oil fill hole.

Note: Do not touch the Handle when

adding the hydraulic oil.

4. Replace the Fill Screw.

5. For model 61406/62457 only: Replace Screw also.

Functions

Figure A

Saddle

Handle

Handle

Socket

Oil Fill Screw

(Not Shown)

Lifting Arm

Rear Caster

Carry Handle

Screw

Fill Screw

Cover Screw for

Safety Valve.

Do not open

or adjust.

61406/

62457

Fill Screw

Safety Valve

Cover Screw.

Do not open

or adjust.

61386

Figure B: Hydraulic Unit

Page 4 For technical questions, please call 1-888-866-5797. Item 61386 61406 62457

Operating Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this

manual including all text under subheadings therein before set up or use of this product.

Lifting

Park vehicle on a flat, level, solid, surface safely away from oncoming traffic. Turn off the vehicle’s engine.

Place the vehicle’s transmission in “PARK” (if automatic) or in its lowest gear (if manual).

Set the vehicle’s emergency brake. Then, chock the wheels that are not being lifted.

1. Turn the Handle counterclockwise to lower the Jack.

Once the Jack is fully lowered, turn the

Handle firmly clockwise to close it.

2. Carefully position the Saddle of the Jack under the

vehicle manufacturer’s recommended lifting point.

(See vehicle manufacturer’s owner’s manual

for location of frame lifting point.)

3. Pump the Handle until the top of the Jack’s Saddle

has nearly reached the vehicle lifting point. Position

the Saddle directly under the vehicle’s lifting point.

4. To lift the vehicle, pump the Handle of the Jack.

Use smooth, full strokes.

5. Once the vehicle is raised, slide a jack stand of

appropriate capacity (not included) under a proper

lifting point referred to in the vehicle owner’s

manual. Always use two jack stands, position them

at the same point on each side of the vehicle.

WARNING! The rated capacity of jack stands is per

pair, not the individual capacities combined unless

specifically noted on the product by the jack stand

manufacturer. Do not exceed rated jack stand capacity.

Ensure that the vehicle support points are fully seated

in the saddle of both jack stands. Use a matched pair

of jack stands per vehicle to support one end only.

Failure to do so may result in the load suddenly falling,

which may cause personal injury and/or property damage.

6. Center the vehicle’s lifting point(s) on the saddle of

the jack stand(s). Set the jack stand(s) to the same

height according to the manufacturer’s instructions,

making sure that they lock securely into position.

7. Slowly turn the Handle counterclockwise to lower

the vehicle onto the saddle(s) of the jack stand(s).

Then, turn the Handle firmly clockwise to close it.

Lowering

1. Carefully remove all tools, parts, etc.

from under the vehicle.

2. Position the Saddle under the lifting point.

Turn the Handle firmly clockwise and raise

load high enough to clear the jack stands,

then carefully remove jack stands.

3. Slowly turn the Handle counterclockwise

(never more than 1/2 full turn) to lower

the vehicle onto the ground.

4. Lower the Jack completely. Then, store in a

safe, dry location out of reach of children.

5. To prevent accidents, turn off the tool and

disconnect its power supply after use. Clean, then

store the tool indoors out of children’s reach.

Page 5For technical questions, please call 1-888-866-5797.Item 61386 61406 62457

Maintenance and Servicing

Procedures not specifically explained in this manual must

be performed only by a qualified technician.

TO PREVENT SERIOUS INJURY FROM TOOL FAILURE:

Do not use damaged equipment. If abnormal noise or vibration occurs,

have the problem corrected before further use.

Cleaning, Maintenance, and Lubrication

1. Before each use, inspect the general condition of

the Jack. Check for broken, cracked, or bent parts,

loose or missing parts, and any condition that

may affect the proper operation of the product.

If a problem occurs, have the problem corrected

before further use.

Do not use damaged equipment.

2. Before each use, thoroughly test the Jack

for proper operation prior to its actual use.

If the Jack appears not to be working properly,

follow Bleeding instructions on page 3.

3. Change the hydraulic oil at least

once every three years:

A. With the Jack fully lowered, remove the

Oil Filler Plug on the side of the Housing.

B. Tip the Jack to allow the old hydraulic oil

to drain out of the Housing completely,

and dispose of the old hydraulic oil in

accordance with local regulations.

C. With the Jack upright, completely fill the

Housing with a high quality hydraulic oil (not

included) until the oil is 1/4″ below the fill hole.

D. Open the valve by turning the Handle

counterclockwise and pump the Handle

to bleed air from the system.

E. Recheck oil level and re-fill as needed.

F. Reinstall the Oil Filler Plug.

7. Wipe dry with a clean cloth. Then, store the

Jack in a safe, dry location out of reach of

children and other non-authorized people.

Troubleshooting

TO PREVENT SERIOUS INJURY:

Use caution when troubleshooting a malfunctioning jack. Stay well clear of the supported load.

Completely resolve all problems before use. If the solutions presented in the Troubleshooting guide

do not solve the problem, have a qualified technician inspect and repair the jack before use.

After the jack is repaired: Test it carefully without a load by raising and lowering it fully,

checking for proper operation, BEFORE RETURNING THE JACK TO OPERATION.

DO NOT USE A DAMAGED OR MALFUNCTIONING JACK!

POSSIBLE SYMPTOMS

PROBABLE SOLUTION

(Make certain that the jack is not supporting a load while attempting a solution.)

Jack will

not lift at

its weight

capacity

Saddle

lowers

under

load

Pump

stroke

feels

spongy

Saddle

will not

lift all

the way

Handle

moves up

when jack is

under load

Oil leaking

from filler

plug

X X Check that Release Valve is fully closed.

Bleed air from the system.

X X X

Valves may be blocked and may not close fully. To flush the valves:

1. Lower the Saddle and securely close the Release Valve.

2. Manually lift the saddle several inches.

3. Open the release valve and force the saddle down as quickly as possible.

XX X Jack may be low on oil. Check the oil level and refill if needed.

Jack may require bleeding - see instructions on page Bleeding on page 3.

XUnit may have too much hydraulic oil inside, check fluid level and adjust if needed.

Page 6 For technical questions, please call 1-888-866-5797. Item 61386 61406 62457

Parts Lists and Assembly Diagrams

61406 Parts List and Assembly Diagram

1

23

4

56

78

9

11 10

12 13 14

21

15

16

13

17

16

16

13

12

19

20

24

22

23 20

25

26

27

28

29

33

32 31 30

34

35

37

38

39

41

42

43 40

36

8

18

Part Description Qty

1 Axle 1

2 Linkage Rod 2

3 Retaining Ring 2

4 Screw 4

5 Spacer Sleeve 2

6 Front Wheel 2

7 Washer 2

8 Nut 4

9 Handle Bar 2

10 Screw 2

11 Spring Washer 2

12 Washer 4

13 Spring Washer 10

14 Screw 2

15 Rear Cast 2

16 Screw 6

17 Screw 2

18 Rear Cast Saddle 2

19 Screw 2

20 Spring Washer 6

21 Nut 2

22 Spacer Sleeve 2

Part Description Qty

23 Screw 4

24 Handle Socket Axle 2

25 Power Unit 1

26 Handle Socket Assembly 1

27 Handle Sleeve 1

28 Handle Upper 1

29 Handle Lower 1

30 Spring 2

31 Elastic Pin 1

32 Pull Rod 2

33 Retaining Ring 2

34 Block Linkage 1

35 Eye Bolt 2

36 Connecting Rod Pin 2

37 Rubber Sleeve 2

38 Handle Socket Rod 1

39 Shaft 1

40 Lift Arm 1

41 Limit Axle 1

42 Saddle Base Axle 1

43 Side Plate 2

Page 7For technical questions, please call 1-888-866-5797.Item 61386 61406 62457

1

2

34

38

5

67

8

9

10

13

11 12

1415 16 17 18

20

19

21

10

16

15

14

22

23

24

25

15

27

33 28

29

30

31

32

34

36

35

37

39

40

41

43

44

16

42

45

26

1

3

2

4

5

6

78

9

1110

12 13 14

15

16 17

17

18

19

8

20

16

21

14

13

22

25

2413

23

26

27

30

29

28

31

32

33

34

35

36

37

38

39

40

43

41

42

Part Description Qty

1Front Axle Cover 1

2 Axle 1

3 Linkage Rod 2

4 Retaining Ring 2

5 Screw 4

6 Screw 6

7 Spacer Sleeve 2

8 Front Wheel 2

9 Washer 2

10 Nut 4

11 Spring Washer 2

12 Screw 2

13 Handle Bar 2

14 Washer 4

15 Spring Washer 8

16 Screw 8

17 Spring Washer 8

18 Screw 8

19 Screw 4

20 Rear Cast 2

21 Rear Cast Saddle 2

22 Screw 2

23 Spring Washer 2

24 Nut 2

25 Handle Socket Axle 2

26 Spacer Sleeve 2

27 Retaining Ring 2

28 Power Unit 1

29 Handle Socket Assembly 1

30 Handle Sleeve 1

Part Description Qty

31 Handle Upper 1

32 Handle Lower 1

33 Pull Rod 2

34 Elastic Pin 1

35 Block Linkage 1

36 Spring 2

37 Eye Bolt 2

38 Connecting Rod Pin 2

39 Rubber Sleeve 2

40 Handle Socket Rod 1

41 Shaft 1

42 Lift Arm 1

43 Limit Axle 1

44 Saddle Base Axle 1

45 Side Plate 2

Part Description Qty

1 Axle 1

2 Linkage Rod 2

3 Retaining Ring 2

4 Screw 2

5 Spacer Sleeve 2

6 Front Wheel 2

7 Washer 2

8 Nut 4

9 Handle Bar 1

10 Screw 2

11 Spring Washer 2

12 Washer 2

13 Spring Washer 8

14 Screw 4

15 Rear Cast 2

16 Spring Washer 8

17 Screw 4

18 Screw 2

19 Rear Cast Saddle 2

20 Screw 2

21 Washer 2

22 Nut 2

23 Spacer Sleeve 2

24 Screw 4

25 Handle Socket Axle 2

26 Power Unit 1

27 Handle Socket Assembly 1

28 Handle Sleeve 1

29 Handle Upper 1

30 Handle Lower 1

Part Description Qty

31 Spring 2

32 Elastic Pin 1

33 Retaining Ring 2

34 Block Linkage 1

35 Eye Bolt 2

36 Connecting Rod Pin 2

37 Rubber Sleeve 2

38 Handle Socket Rod 1

39 Shaft 1

40 Lift Arm 1

41 Limit Axle 1

42 Saddle Base Axle 1

43 Side Plate 1

61386 Parts List and Assembly Diagram

62457 Parts List and Assembly Diagram

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,

and warrants to the original purchaser that this product is free from defects in materials and workmanship for the

period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,

to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper

installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries

to persons or property, or for incidental, contingent, special or consequential damages arising from the use of

our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the

above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER

WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with transportation charges

prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.

If our inspection verifies the defect, we will either repair or replace the product at our election or we may

elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will

return repaired products at our expense, but if we determine there is no defect, or that the defect resulted

from causes not within the scope of our warranty, then you must bear the cost of returning the product.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM

IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR

MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS

QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE

ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY

STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND

LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY

ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS

THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Record Product’s Serial Number Here:

Note: If product has no serial number, record month and year of purchase instead.

Note: Some parts are listed and shown for illustration purposes only,

and are not available individually as replacement parts.