Harbor Freight 3 In 1 Riveter Kit Product Manual 94100

2015-05-27

: Harbor-Freight Harbor-Freight-3-In-1-Riveter-Kit-Product-Manual-723884 harbor-freight-3-in-1-riveter-kit-product-manual-723884 harbor-freight pdf

Open the PDF directly: View PDF PDF.
Page Count: 1

DownloadHarbor-Freight Harbor-Freight-3-In-1-Riveter-Kit-Product-Manual- 94100 Riveter Kit Harbor-freight-3-in-1-riveter-kit-product-manual
Open PDF In BrowserView PDF
TO PREVENT SERIOUS INJURY, READ AND UNDERSTAND ALL WARNINGS AND INSTRUCTIONS BEFORE USE.
WARNING: When using tool, basic safety precautions should always be followed to reduce the risk of personal injury
and damage to equipment. Read all instructions before using this tool!

1.

Pinch Danger. If not properly used, the scissor-like action of this tool may cause pinch injury. Wear protective
gloves and be careful to avoid pinch injury.

2.

Small pieces choking hazard. During riveting, small pins are left as waste. Dispose of rivets and all small
pieces properly.

3.

Prevent eye injury. Wear ANSI approved eye protection when using this tool to prevent eye injury.

4.

Keep children away. Do not let children handle rivets, rivet pins or other small parts.

Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible
conditions and situations that may occur. It must be understood by the operator that common sense and caution are
factors which cannot be built into this product, but must be supplied by the operator.
NOTE: Rivets, rivet nuts and anchor rivets are not supplied with this kit. They must be purchased separately.

To install Blind Rivets (3/16”, 5/32”, 1/8” or 3/32”):
1. Drill the proper sized hole for the rivet you are using.
2. Select and install the correct Nosepiece (11, 12, 13 or 14). Nosepieces have a standard right hand thread
for installing and removing.
3. Place the rivet in the hole, and place the Nosepiece over the stem of the rivet.
4. Squeeze the handle once or twice until the stem snaps off the rivet.
5. Open the handle and turn the tool upside down to allow the stem to fall out.
To install Nut Rivets and Rivet Anchors, you must change the Case. Rivet Nuts and Rivet Anchors use the
same Case.

Changing the Case:
1. Remove any installed Nosepiece by turning it counterclockwise.
2. Hold the Pivot Pin (8) against the handle to prevent it turning. Loosen the Pivot Pin Nut (9) by turning it
clockwise with the Wrench (4).
3. Squeeze the Lever (2) down, and pull it back along the Frame (1). This will disengage the Lever (2) from the
Axis Pin (19).
4. Remove the Jaw Case (15) from the tool.
5. Insert the Nut & Anchor Case (20).
6. Push the Handle back in place, being sure that the Case Pins fit into the Handle slots.
7. Push the Pivot Pin (8) back in place, and retighten it with the Wrench (4).
To install Rivet Nuts (¼-20, 110-24, 8-32 or 6-32):
1. Drill the proper sized hole for the Rivet Nut to be used.
2. Thread the proper Nut Mandrel (21, 22, 23 or 24) onto the Nut & Anchor Case (20).
3. Thread the Rivet Nut onto the Mandrel.
4. Insert the Rivet Nut into the hole and squeeze the handle. This will expand the Rivet Nut in the hole.
5. Unscrew the tool from the Rivet Nut.
To install Anchor Rivets (6-32x1-¼” or 6-32x2-3/8”):
1. Drill the proper sized hole for the Anchor Rivet to be used.
2. Thread the proper Anchor Mandrel (25 or 26) onto the Nut & Anchor Case (20).
3. Thread the Anchor Rivet onto the Mandrel.
4. Insert the Anchor Rivet into the hole and squeeze the handle. This will expand the Anchor Rivet in the hole.
5. Unscrew the tool from the Anchor Rivet.
Parts List
Assembly Diagram

Part # Description

QTY.

Part # Description

QTY.

1

Frame Assembly

1

14

Nose Piece 3/32" Rivet

2

Lever Assembly

1

15

Ja w C a se

1
1

3

Grip

2

16

Jaws

2

4

Wrench

1

17

Jaw Pusher

1

5

L o ck

1

18

Jaw Spring

1

6

Return Spring

1

19

Axis Pin

1

7

Spring Pin

1

20

Nut & Anchor Case

1
1

8

Pivot Pin

1

21

Nut Mandrel Set 1/4 - 20

9

Pivot Pin Nut

1

22

Nut Mandrel Set 10 - 24

1

10

"S" Clip

2

23

Nut Mandrel Set 8 - 32

1
1

11

Nose Piece 3/16" Rivet

1

24

Nut Mandrel Set 6 - 32

12

Nose Piece 5/32" Rivet

1

25

Anchor Mandrel 6 - 32 x 1-¼"

1

13

Nose Piece 1/8" Rivet

1

26

Anchor Mandrel 6 - 32 x 2-3/8"

1

NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts.
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Page Count                      : 1
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:0440c808-64b9-44c1-8b23-39450a55a4c8
Producer                        : Acrobat Distiller 6.0 (Windows)
Keywords                        : 
Creator Tool                    : Adobe PageMaker 7.0
Modify Date                     : 2006:04:07 09:05:15-07:00
Create Date                     : 2006:04:07 09:04:46-07:00
Metadata Date                   : 2006:04:07 09:05:15-07:00
Document ID                     : uuid:5561cf27-6180-4987-b579-9bb209f8c92b
Format                          : application/pdf
Title                           : 94100 Riveter Kit
Creator                         : Steven Miller
Description                     : 94100 Riveter Kit
Author                          : Steven Miller
Subject                         : 94100 Riveter Kit
EXIF Metadata provided by EXIF.tools

Navigation menu