Harbor Freight 42976 Users Manual Drill Mill Manual.p65

42976 42976

42976 to the manual 1266e6c3-6168-4943-8e3e-7e649ea76b8f

2015-01-25

: Harbor-Freight Harbor-Freight-42976-Users-Manual-209620 harbor-freight-42976-users-manual-209620 harbor-freight pdf

Open the PDF directly: View PDF PDF.
Page Count: 16

DownloadHarbor-Freight Harbor-Freight-42976-Users-Manual- 42976 Drill Mill Manual.p65 Harbor-freight-42976-users-manual
Open PDF In BrowserView PDF
12 Speed
Drill / Mill Machine
Model 42976

Assembly & Operating Instructions

www.HarborFreight.com
Copyright 2000 by Harbor Freight Tools®. All Rights Reserved.
No portion of this manual or any artwork contained herein may be reproduced in any
manner, shape or form without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353.

SPECIFICATIONS
Motor:
120V/60Hz Single Phase
Drill Capacity:
1/2 HP, 8.5 Amps with Load Face Mill Capacity:
12 Speeds (rpm):
300-400-540-720-900End Mill Capacity:
1040-1500-1740-2100-2260-3100-3840
Max. Chuck to Table:
Motor rpm’s:
1700
Column Diameter:
Drive Type:
V-belt / Pulley
Table Slots:
Spindle Taper:
MT-2, Diameter: 1.265”
Head Rotation:
Spindle Stroke:
3-3/8”
Net Weight:

4, 5 and 6mm Hex Wrenches
Drift Pin
Drill Chuck

5/8”
1-1/2”
5/8”
10”
2.830”
1/2” x 2
360O
470 Lbs.

INCLUDED ACCESSORIES
Chuck Key
Stand Assembly
Precision 0-70O vise

FEATURES
1.
This machine may be used for surface cutting, drilling, milling, and tapping.
2.
The high quality of this machine, and its ease of operation makes it suitable for use by students,
amateurs, and home hobbyists, as well as skilled technicians.
3.
Drilling and milling may be done using hand operated feeding. Milling is done with the quill locked via
Clamp Handle (#83) *.
4.
Many of the adjustable nuts are bronze, for adjusting thread clearance and reducing wear. These
bronze parts also allow screws to rotate smoothly and improve accuracy.
5.
The vertical column is very strong and stiff, which makes the machine very stable and improves
accuracy of manufactured parts.
6.
The machine head is cast steel, and has been heat-treated, stress-relieved, and precision machined.
7.
Machine gears are precision ground for smooth operation.
8.
Speeds can be easily changed.
9.
Thread tapping operations can be done in either rotation, and working depth can be controlled using a
positive stop gauge.
SAVE THIS MANUAL
You will need the manual for the safety warnings and cautions, assembly instructions, operating procedures,
maintenance procedures, trouble shooting, parts list, and diagram. Keep your invoice with this manual.
Write the invoice number on the inside of the front cover. Keep both this manual and your invoice in a safe,
dry place for future reference.
NOTICE
The Warnings, Cautions, and Instructions discussed in this instruction manual cannot
cover all possible conditions and situations that may occur. It must be understood by
the operator that common sense and caution are factors which cannot be built into this
product, but must be supplied by the operator.
* For fine adjustment, use a dial test indicator (not included) mounted either to the table or workpiece, and
reference a point on the chuck or quill colar that is convenient. Loosen the Clamp Handle (#83) slightly,
then tap the chuck feed lever lightly, as you observe the indicator dial.
Page 2 SKU # 42976

REV 08/03

SAFETY WARNING & CAUTIONS
READ ALL INSTRUCTIONS BEFORE USING THIS TOOL!
1. KEEP WORK AREA CLEAN. Cluttered areas invite injuries.
2. OBSERVE WORK AREA CONDITIONS. Do not use tools in damp, wet, or poorly lit locations.
Don’t expose to rain. Keep work area well lit. Do not use electrically powered equipment in the presence
of flammable gases or liquids.
3. KEEP CHILDREN AWAY. Children must never be allowed in the work area. Do not let them handle
machines, tools, or equipment.
4. STORE IDLE EQUIPMENT. When not in use, tools must be locked up in a dry location to inhibit
rust. Always lock up tools and keep out of reach of children.
5. DO NOT FORCE THE TOOL. It will do the job better and more safely at the rate for which it was
intended. Do not use inappropriate attachments in an attempt to exceed the tool’s capacities.
6. USE THE RIGHT TOOL FOR THE JOB. Do not use a tool for a purpose for which it was not
intended.
7. DRESS PROPERLY. Do not wear loose clothing or jewelry, as they can be caught in moving parts. Nonskid footwear is recommended. Wear restrictive hair covering to contain long hair. Always wear appropriate
work clothing.
8. USE EYE, EAR AND BREATHING PROTECTION. Always wear ANSI approved impact safety
goggles if you are producing metal filings or wood chips. Wear an ANSI approved dust mask or
respirator when working around metal, wood, and chemical dusts and mists. Use ANSI approved ear
protection when working in a loud or noisy environment.
9. DO NOT ABUSE THE POWER CORD. Protect the power cord from damage, either from impacts,
pulling or corrosive materials. Do not yank machine’s cord to disconnect it from the receptacle.
10. DO NOT OVERREACH. Keep proper footing and balance at all times. Do not reach over or across
running machines.
11. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer performance.
Follow instructions for lubricating and changing accessories. Inspect power cord periodically and, if
damaged, have it repaired by an authorized technician. Inspect all hydraulic seals for leaks prior to use.
Control handle and power switch must be kept clean, dry, and free from oil and grease at all times.
12. REMOVE ADJUSTING KEYS AND WRENCHES. Be sure that keys and adjusting wrenches are
removed from the tool or machine work surface before operation.
13. AVOID UNINTENTIONAL STARTING. Be sure that you are prepared to begin work before turning the
start switch on.
Page 3 SKU # 42976

14. STAY ALERT. Watch what you are doing. Do not operate this machine when you are tired.
15. DO NOT OPERATE THIS MACHINE WHILE UNDER THE INFLUENCE OF ALCOHOL, DRUGS,
OR PRESCRIPTION MEDICINES.
16. CHECK FOR DAMAGED PARTS. Before using any tool, any part that appears damaged should be
carefully checked to determine that it will operate properly and perform its intended function. Check for
alignment and binding of moving parts, any broken parts or mounting fixtures, and any other condition that may
affect proper operation. Any part that is damaged should be properly repaired or replaced by a qualified
technician. Do not use the tool if any switch does not turn on and off properly.
17. REPLACEMENT PARTS AND ACCESSORIES. When servicing, use only identical replacement parts
intended for use with this tool. Replacement parts are available from Harbor Freight Tools. Use of any other
parts will void the warranty.
18. USE THE RIGHT TOOL FOR THE JOB. Do not attempt to force a small tool or attachment to do the
work of a larger industrial tool. There are certain applications for which this tool was designed. Do not modify
this tool and do not use this tool for a purpose for which it was not intended.
19. MAINTENANCE. For your own safety,maintenance should be performed regularly by a qualified
technician.
SPECIAL WARNINGS WHEN USING THIS DRILLING / MILLING MACHINE
Using this machine may create special hazards.
Take particular care to safeguard yourself and those around you.
Electrical Safety. Never operate any tool if there is an electrical hazard. Never operate an electrical
tool in wet conditions. Never operate a tool with an improper electrical cord or extension cord. Never operate
an electrical tool unless you are plugged into a properly grounded outlet, which supplies 110-120 Volts at
60 Hz. We recommend you use a circuit which is protected by an appropriate circuit breaker.
Ejected Material. Use safe practices to avoid injury from ejected material. Because milling tools and
workpieces turn at high speed, there is a danger of being injured by materials that may be ejected. Always wear
ANSI-certified eye protection. Never attempt to machine any item if it is not adequately held. Always stand to
one side of the plane in which the materials are spinning, to avoid being hit if an item is ejected. Never allow
bystanders to be in the proximity of this machine while in operation.
Entanglement. Use extreme caution to prevent loose materials from being caught in the machine.
Never operate this machine with loose clothing, long hair, jewelry, or other items which may become caught in
the tool or workpieces. In case of entanglement, press the OFF switch immediately.
NOTICE: No list of warnings can be all inclusive. The operator must supply common
sense, and operate this tool in a safe manner.

Page 4 SKU # 42976

FEATURES AND CONTROLS OF THE #42976 DRILL / MILL MACHINE
16

15

28

13
14
17

28

6
5

8

4

11
7

12

18

10
3

19

1

9

2
3

9

22

20

20

26

23
26
25

25

24
21
1. Column
2. Gear Strip
3. Head Crank
4. Vertical Head Lock
5. Chuck Feed Lever
6. Chuck Travel Limit Screw
7. Reference Scale
8. Chuck Fixing Lever
9. Chuck
10. Chuck Spindle

Page 5 SKU # 42976

11. Chuck Spindle Collar
12. Motor
13. Drive Belt Cover
14. Motor Pulley
15. Transfer Pulley
16. Drive Pulley
17. Drive Belt Tension Lever
18. Drive Belt Tension Fixing Bolt
19. Head Rotation Control Lever
20. Horizontal Control Wheels (2)

27
21. Cross Feed Control Wheel
22. Butterfly Table Lock Bolts (4)
23. T-Slots (2)
24. Tray
25. Mounting Bolts (4)
26. Table Travel Stops (2)
27. Table Travel Limiter
28. Drive Belt Speed Chart
29. Drive Belts (2)

1.
2.
3.

1.
2.
3.
1.

2.

3.
4.
5.

1.

2.
3.

UNPACKING AND INSTALLATION
Remove protective crating and skids carefully. In the event of damage in transit, contact Harbor Freight
Tools immediately.
The machine is carefully inspected and tested in operation before it leaves the factory. If any
defects are found on delivery, contact us immediately.
Read the owner’s manual and become familiar with the parts and controls on the drawings before
using this machine, as familiarity with the controls will enhance your ability and safety in using it.
ASSEMBLY
After removing the machine from the crate and cleaning it, it must be mounted before use.
This machine can be mounted directly on a worktable, optional Stand (#42977), or floor.
The drill chuck must be installed.
INSTALLATION
It is important that the machine be located on a hard, solid,
level floor, worktable, or optional base, which is capable of
supporting this heavy machine and the workpieces that are
produced. Find a location that supplies easy access to 120
Volt electrical service. Make sure this machine is located in a
well lighted and well ventilated area. The floor should be
resistant to vibration.
Warning: Drill/Mill machines are inherently top heavy.
Before moving the machine, be sure the head is fixed on the
column. Before moving, lower the head as much as possible
to lower the center of gravity. When moving the machine be
careful to keep it balanced; do not allow it to topple over.
To set the machine on a solid concrete foundation, it’s
advisable to apply a little grout to touch up any uneveness in
the concrete in order to get a solid foundation at all points.
When setting machine on a floor or worktable that has any
surface irregularities, shims should be used to correct this
condition to the greatest extent possible.
There are 4 holes in the base for mounting the machine
permanently to a smooth, solid, and level floor,
worktable, or optional stand (#42977).
CLEANING AND LUBRICATION
Thoroughly clean the machine with a commercial degreaser.
Do not use gasoline, kerosene or other flammable liquids.
Avoid getting solvent on rubber parts, or into the electrical
controls or motor.
After cleaning, coat all bright metal with a light lubricant to
prevent corrosion.
Lubricate all gears and moving parts with a medium
consistency machine oil.

Figure 1. Shown with optional stand.
P/N #42977

LEVELING THIS MACHINE
1.
Before operation, it is critical to level the work table both lengthwise and crosswise, using a precision
level. It will not be possible to maintain accuracy of machined parts if the mill is not properly leveled.
Page 6 SKU # 42976

EXTENSION CORDS
Note: Performance of this tool may vary depending on variations in local line voltage.
Extension cord usage may also affect tool performance.
Your tool has a three-prong plug, therefore you must use a three-prong extension cord. Only use
rounded jacket extension cords listed by the Underwriters Laboratories (UL). Improper use of extension
cords may cause inefficient operation of your tool which can result in overheating. Be sure your extension
cord is rated to allow sufficient current flow to the motor.
If you are using the tool outdoors, use an extension cord rated for outdoor use (signified by “WA”
on the jacket).
The extension cord must have a minimum wire size depending on the amperage of the tool and the
length of the extension cord. This size is determined by its AWG (American Wire Gauge) rating. The smaller
the gauge, the greater the cable’s capacity. The amount of cords used does not matter: Total length determines
the minimum AWG rating. Every cord must meet the AWG rating. Use the chart below to determine what
AWG rating is required for your situation. Cord length is rated in feet. Harbor Freight Tools can supply UL
listed and outdoor rated cords in most AWG ratings as needed.
AWG RATING CHART
CORD LENGTH
AMPS
0-10.0
10.1-13.0
13.1-15
15-18

25’
AWG
18
16
14
14

50’
AWG
18
16
14
12

75’
AWG
16
14
12
12

100’
AWG
16
14
12
12

125’
AWG
14
14
12
12

150’
AWG
14
12
12
12

175’
AWG
12
12
12
—-

200’
AWG
12
12
——-

GROUNDAGE/VOLTAGE WARNING
Common household current is 110-120 volts. As long as the outlet used with the Power Table
Feed is rated from 110-120V there will be no complications using it with household receptacles. Plug the
tool into a 110-120V properly grounded outlet protected by a 15-amp, dual element time delay or circuit
breaker.
NEVER try to plug a 110-120V tool into a 220-240V circuit or serious complications and possible
injury to the operator may occur. The plugs have different shapes to prevent this.
This tool has a three-prong plug. The third (round) prong is the ground. Cutting off the ground will
result in a safety hazard and void the warranty.
If the outlet you are planning to use is the two-prong type, do not remove or alter the grounding
prong in any manner. Use an adapter and always connect the grounding lug to a known grounding source.
It is recommended that you have a qualified electrician replace the two-prong outlet with a properly
grounded three- prong outlet.
Page 7 SKU # 42976

BASIC OPERATION
For reference numbers mentioned in these instructions, please see page 5.
WARNING: Unplug the drill from its power source before changing bits or attempting any repairs,
adjustments or maintenance.
Basic Controls
1.
Raise and lower the Head by using the Head Crank (#3).
2.
Feed the Chuck (#9) using the Chuck Feed Lever (#5).
Chuck movement may be limited using the Chuck
Travel Limit Screw (#6).
3.
Move or feed the Table from side to side using either
Horizontal Feed Control Wheels (#20).
4.
Move the Table front to back using the Cross Feed
Control Wheel (#21).
5.
Attach workpieces to the Table using jigs or fixtures
(not included) or the included precision 70O vise
attached to the T-slots (#23).
6.
The machine can be turned ON and OFF by using
the power switch located on the left side of the
Head. The upper Switch marked | turns the machine
ON. The lower switch marked O turns the
machine OFF.
WARNING: The machine will continue to run as long
as the power cord is plugged in, and the switch is
turned ON. Never leave the machine unattended while
it is running.
Figure 2. Drill Head Controls
Installing the Chuck
The Chuck and Chuck Spindle both have a self-centering MT-2 taper.
1.
Wipe a small amount of grease onto the spindle to prevent corrosion.
2.
Place the chuck onto the spindle, pressing it upward with a twisting motion. Tap the chuck gently home,
using a soft-faced mallet.
3.
If desired, fine tune the chuck using a dial indicator. To do this, mount a dial indicator firmly on the table.
Place the dial indicator pointer in contact with the chuck, and adjust the dial to zero. Slowly rotate the
chuck and read any out of center on the indicator. Carefully tap the chuck with a mallet upward and to
the side as needed to center the chuck. Continue this process until you are satisfied with the adjustment.
To insert and remove drill or milling bits, use the chuck key provided.
1.
Insert the Chuck Key into one of the holes in the Chuck, so that it meshes with the cogs on the Chuck.
2.
Turn the Chuck Key counterclockwise to open the flanges in the Chuck. Continue to turn the Chuck
Key until the opening is large enough to accept the Bit.
NOTE: the largest bit size capacity of this Chuck is 5/8” diameter.
3.
Insert the Drill Bit into the Chuck.
4.
Turn the Chuck Key clockwise to tighten the jaws around the drill bit shaft. Ensure that the drill bit is
seated securely before starting.
5.
Remove the Chuck Key, and replace it in its holder before starting.
Page 8 SKU # 42976

Preparing for Drilling
1.
The Chuck (#9) is installed on the Spindle (#10) using a Morris Taper. This is a self-centering design.
2.
Rotate the Chuck Fixing Lever (#8) counterclockwise to loosen the Spindle for vertical travel.
3.
You can move the Spindle and Chuck vertically by operating the Chuck Feed Lever (#5).
4.
Vertical movement of the Chuck and Spindle can be limited by setting the Chuck Travel Limit Screw
(#6). A Reference Scale (#7) indicates the relative travel of the Chuck.
5.
For drilling blind holes (which do not pass through
the workpiece), set the Chuck Travel Limit Screw
(#6). To do so, first determine the desired depth.
Then adjust the Limit Screw so that the distance from
the tip of the drilling bit to the end of the gauge is
equal to the desired depth.
6.
For drilling holes that pass through the workpiece,
loosen the Limit Screw so it does not interfere with
the vertical travel of the spindle.
7.
Be sure that the Vise or other fixture used to hold the
workpiece is properly attached to the table, and
aligned with the drill bit. Adjust alignment using the
vertical and cross table control wheels. The table can
be locked into position using the four Butterfly Lock
Bolts (#22) which are located under the Table on
the right side, and above the Cross-Feed Control Wheel.
Figure 3. Table Control Wheel
and Butterfly Lock Bolts.
Adjusting the Head
1.
To raise or lower the head, loosen the Vertical Head
Lock (#4). Use the Head Crank (#3) to raise or
lower the head on its Gear Strip (#2) and
Column (#1).
2.
The head may be rotated on the column by loosening
the Control Lever (#19). Adjust the head to the
desired angle, then fix the Control Lever. Periodically
check the tightness of this lever, especially during
prolonged use of the machine.
Adjusting Table Slack and Compensating for Wear
1.
Your machine is equipped with gib strip adjustment
to compensate for wear and excess slack on cross
and horizontal travel.
2.
Rotate the gib strip bolt slightly counterclockwise to
tighten the gib strip. Rotate it slightly clockwise to
loosen the gib strip.
3.
Adjust the gib strip bolt until very slight drag is felt
when moving the table.

Page 9 SKU # 42976

Figure 4. Gib StripAdjustment.

Preparing for Milling
1.
Loosen the Chuck Travel Limit Screw (#6).
2.
Install the cutting bit needed to perform the intended milling operation.
3.
Using the Chuck Feed Lever (#5), adjust the bit to approximately the correct height. Tighten the Chuck
Fixing Lever (#8).
4.
Set the final vertical adjustment using your milling jig or fixture (not included) or the included 70O
precision vise.
5.
Set the horizontal adjustment using the Horizontal (#20) or Cross Feed Control Wheels (#21).
6.
Depending on whether the cut will be made in the X-axis (left or right) or the Y-axis (front to back) one
dimension of the table can be locked into place using one of the two pairs of Butterfly Lock Bolts (#22)
located under the Table on the right side or above the Cross Feed Control Wheel.
Moving the Table
1.
The table can be moved horizontally and front to back by using the Control Wheels.
2.
If the table is to be moved in one direction only, it can be prevented from moving in the other by
tightening the butterfly bolts under the right side or front of the table. The table can also be locked in
both directions, for example when drilling.
3.
The table travel from left to right can also be limited by adjusting the position of the Table Stops (#26).
Changing Machine Speed
1.
Turn the power off and unplug the power cord.
2.
To select the proper speed, loosen the Drive Bolt
Tension Fixing Bolt (#18), then loosen the Drive Belt
Tension Lever (#17).
3.
Open the Drive Belt Cover (#13).
4.
Following the speed chart which is mounted on the
front of the head, position the two drive belts on the
pulleys to achieve the desired speed.
5.
Tension the belts by moving the Drive Belt Tension
Lever (#17). Secure the belt tension by tightening
the Fixing Bolt (#18).

Figure 5. Machine Speed Drive Belt Settings.

TROUBLE SHOOTING
WARNING! Never perform trouble shooting or maintenance unless the tool is turned OFF
and unplugged from its power supply.
The motor overheats, or there is insufficient power.
1.
The machine is overloaded. Reduce the feed rate, and/or increase the spindle speed.
2.
The voltage supply is too low. If you have an unreliable power supply, check with a qualified electrician
to repair it.
3.
The motor carbon brushes may be worn or cracked. Check them and replace if needed.
4.
There may be a poor electrical connection. Have a qualified electrician check the wiring and power
supply.
5.
The motor may be burned out. After a long period of heavy use, the motor may burn out. If so, replace
the motor.
6.
The drill bit or cutting blade may be worn. Sharpen or replace the bits as needed.
Page 10 SKU # 42976

The machine doesn’t run when the power switch is turned ON.
1.
The power cord is not plugged in.
2.
The chuck spindle may be bound by the workpiece, cutting bit or fixture.
3.
If there is a surge in the current, the circuit breaker may have opened. Press the circuit breaker back in,
if it is in the open position.
4.
The belt tension may not be tight. Adjust the tension lever and lock it in place.
The spindle bearing is very hot.
1.
There is insufficient lubrication. Turn off the power, and check the bearing for lubrication. If necessary,
apply a medium weight bearing grease.
2.
The spindle bearing is worn, or is fixed too tight. Turn off the power, unplug the electrical connection,
and rotate the spindle by hand. Be sure it turns freely. If not, check the bearing adjustment. If you feel
uneveness in the bearing, you will have to replace it.
3.
The spindle has been turning at high speed for a long time. After long use, turn the machine off for a
while to give it a rest, and allow it to cool off.
The table travel is not balanced
1.
The spindle taper gap is too wide. Adjust the arbor bolt properly.
2.
One of the leaf bolts may be loose. Check and tighten them if necessary.
3.
The feed is too deep. Reduce the depth of the cut, and make several passes to reach the required depth.
4.
The gib strip may be out of adjustment. Check it and adjust it if necessary.
There is a vibration,and the cut is not smooth
1.
The spindle bearing may be improperly adjusted or is worn. Check it and adjust or replace as
necessary.
2.
The spindle is loose up and down. Check the adjustment of the two inner bearing covers. Adjust them
so there is no free play in the taper bearing, and the bearing turns freely. Tighten them against each other
to save this adjustment.
3.
The gap of the taper sliding plate is too wide. Adjust the bolt tension.
4.
The chuck is loose. Tighten the chuck.
5.
The drill bit or cutter is dull. Sharpen or replace it. Be sure to use cutting fluid to preserve tool life.
6.
The workpiece is not held firmly. Check the clamps or vise you are using, and assure that the workpiece
cannot move.
The workpiece is not machined accurately
1.
A heavy workpiece may be out of balance. Check to see that heavy workpieces are held in balance.
Out of balance pieces may shift when being machined.
2.
A hammer has been used on the workpiece. Never strike the workpiece with a hammer.
3.
The table may not be level. Check the table with a spirit level to be sure it is level both side to side and
front to back.
4.
The machine may not be stable in the floor. Check to be sure the machine is firmly mounted to the floor.

Page 11 SKU # 42976

MAINTENANCE
After each use:
1.
Turn off the power switch and unplug the machine from its power source.
2.
Remove any tool bits, clean and lubricate them, and return them to their storage case.
3.
Using a stiff bristle brush, brush off all chips and shavings left from the machining operation.
4.
Using a rag, wipe off any excess or dirty oil or cutting fluid left on the machine.
5.
Lubricate geared, moving and machined metal parts. Apply light grease or oil to all unpainted metal to
prevent corrosion.
6.
Cover the machine to prevent dust or dirt contamination when not in use.
Daily Maintenance:
1.
Check the tightness of the mounting bolts holding the head in place.
2.
If overheating is observed, or unusual noises are produced, stop the machine immediately to check for
lack of lubrication, faulty adjustments, dull tool bits, or other deficiencies. Correct any problems before
resuming work.
3.
Keep the work area clean. If chips or shavings accumulate on the table or fixtures, shut off the power
and clean the chips away with a stiff bristle brush. Re-check the lubrication before continuing.
Weekly Maintenance:
1.
Clean and coat the lead screws with oil.
2.
Check the lubrication of the sliding parts of the table. Apply light grease if needed.
Monthly Maintenance:
1.
Adjust the accuracy of the slides on both the cross and longitudinal feeds.
2.
Lubricate the bearings, worm gear and worm shaft with light grease.
Yearly Maintenance:
1.
Adjust the table to assure that it is level in all directions.
2.
Check the electrical cord, plug, circuit breakers and related connections to assure that they are secure
and safe.

NOTE: Some parts are listed and shown for illustration purposes only
and are not available individually as replacement parts.

PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS
A REFERENCE TOOL ONLY: NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT:
IN FACT THE MANUFACTURER A ND/OR DISTRIBUTOR EXPRESSLY STATES THATALL REPAIRS AND
PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT
BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO
THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Page 12 SKU # 42976

DRILL / MILL MACHINE, TABLE AND BASE PARTS LIST
Please refer to Parts Diagram on Page 14.
P/N
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33

Description
Base (Not Included)
Door (Not Included)
Hinge (Not Included)
Screw (Not Included)
Oil Tray
Base
Screw
Saddle
Nut
Washer
Screw
Nut
Table
Long Gib
Adjustment Screw
Longitudinal Lead Screw
Support
Screw
Ball Bearing
Scale Ring
Handle Wheel
Key
Washer
Nut
Handle Collar
Handle
Screw Bracket
Dog
Screw
Support
Screw
Ball Bearing
Scale Ring

Quantity
1
1
2
1
1
1
4
1
1
1
1
1
1
1
1
1
1
4
1
1
1
2
1
1
1
1
2
2
2
1
4
1
1

P/N
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67

Description
Handle Wheel
Washer
Nut
Handle Collar
Handle
Cover
Screw
Screw
Handboard
Pin
Crosswise Lead Screw
Short Gib
Adjustment Screw
Ball Bearing
Support
Screw
Ball Bearing
Scale Ring
Handle Wheel
Key
Nut
Handle Collar
Handle
Support (Rest)
Screw
Worm Gear
Handle
Pin
Gear
Clamp Handle
Rack
Column
Dust Cover
Screw

Quantity
1
1
1
1
1
1
3
2
2
2
1
1
1
1
1
4
1
1
1
1
1
1
1
1
4
1
1
1
1
1
1
1
1
1

NOTE: Parts # 1 - 4 represent the optional stand # 42977, which is not included in item # 42976.

Page 13 SKU # 42976

#42976 DRILL / MILL MACHINE, TABLE AND BASE PARTS DIAGRAM
Please refer to Parts List on Page 13.

Note: Parts for optional Stand are shown
but not included with the Drill / Mill machine.

Page 14 SKU # 42976

P/N
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103

#42976 DRILL / MILL MACHINE, HEAD PARTS LIST
Please refer to Parts Diagram on Page 16
Description
Quantity P/N Description
Body
1
104
Headless Set Screw
Screw
2
105
Nut
Shifter Bar
1
106
Nut
Pin
1
107
Slide Bar
Pin
1
108
Pulley Cover
Feed Shaft
1
109
Washer
Pin
1
110
Screw
Scale Ring
1
111
V-Belt
Handle Body
1
112
Nut
Scale
1
113
Spindle Pulley
Screw
1
114
Spring Sleeve
Handle Bar
3
115
Retaining Ring
Knob
3
116
Ball Bearing
Screw
1
117
Collar
Screw
1
118
Ball Bearing
Clamp Handle
2
119
Retaining Ring
Spring Seat
1
120
Nut
Spring Plate
1
121
Washer
Spring Cap
1
122
Ball Bearing
Screw
1
123
Sleeve
Screw
1
124
Ball Bearing
Screw
2
125
Dust Cover
Switch
1
126
Spindle
Wire
1
127
Spindle Bar
Screw
2
128
Drill Chuck
Rubber Bushing
1
129
Wedge Shifter
Wire Clip
1
130
Key
Shaft
1
131
Center Pulley Shaft
Pin
1
132
Ball Baring
Screw
1
133
Collar
Nut
4
134
Ball Bearing
Washer
4
135
Retainging Ring
Motor Base
1
136
Retainging Ring
Motor
1
137
Center Pulley
Screw
4
138
V-Belt
Motor Pulley
1
139
Pulley Cover

Page 15 SKU # 42976

Quantity
1
1
1
2
1
4
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1

#42976 DRILL / MILL MACHINE, HEAD PARTS DIAGRAM
Please refer to Parts List on Page 15.

Page 16 SKU # 42976
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Create Date                     : 2003:08:04 11:03:40-07:00
Modify Date                     : 2003:08:04 11:03:40-07:00
Page Count                      : 16
Creation Date                   : 2003:08:04 18:03:40Z
Mod Date                        : 2003:08:04 18:03:40Z
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Author                          : mbidwell
Metadata Date                   : 2003:08:04 18:03:40Z
Creator                         : mbidwell
Title                           : 42976 Drill Mill manual.p65
EXIF Metadata provided by EXIF.tools

Navigation menu