Harbor Freight 500 Lb Capacity Aluminum Mobility Wheelchair And Scooter Carrier Product Manual
Harbor-Freight-67599-Owner-S-Manual harbor-freight-67599-owner-s-manual
2015-05-27
: Harbor-Freight Harbor-Freight-500-Lb-Capacity-Aluminum-Mobility-Wheelchair-And-Scooter-Carrier-Product-Manual-723497 harbor-freight-500-lb-capacity-aluminum-mobility-wheelchair-and-scooter-carrier-product-manual-723497 harbor-freight pdf
Open the PDF directly: View PDF 
.
Page Count: 12
Page 2 For technical questions, please call 1-800-444-3353. Item 67599
Specifications
Load Capacity 500 lb.
Vehicle Hitch Receiver Size 2" - Class III or better hitches
Inside Platform 47" L x 27-5/8" W x 7-1/2" H
Exterior Platform 49-7/8" L x 29-1/2" W x 8-1/2" H
Removable Ramp 41-1/2" L x 27-3/4" W x 1-1/2" H
Overall Dimensions w/ ramp up 50" L x 40-1/2" W x 43-1/2" H
Important Safety Information
Specific Safety Rules
1. Do not ride in vehicle being loaded or
unloaded. Load and unload vehicle
slowly, according to manual instructions.
2. Do not use if carrier is higher than
12.5” from bottom of ramp.
3. Follow DOT guidelines for use.
4. Do not exceed 500 lb. capacity. Be
aware of dynamic loading! Sudden
load movement may briefly create
excess load causing product failure.
5. Do not exceed 55 MPH while
carrier is attached.
6. Remove ramp and secure
load before moving.
7. Turn vehicle’s ignition OFF
and set parking brake before
loading or unloading.
8. Keep ramp clean.
9. This product is not a toy. Do not allow
children to play with or near this item.
10. Use as intended only.
11. Inspect before every use; do not use
if parts are loose or damaged.
12. Wear ANSI-approved safety goggles
and heavy-duty work gloves during
use. Prior to transporting a load
make sure the Ramp of the Carrier
is in its upright position and locked in
place with the Pins and Lock Pins.
13. Both feet of the Carrier’s Ramp must
rest flat on a solid, level, and flat surface
when loading and unloading an object.
14. Only use the Carrier with a properly
installed Class III or better 2 inch
hitch receiver capable of supporting
the Carrier and its load.
15. Maintain product labels and
nameplates. These carry important
safety information. If unreadable
or missing, contact Harbor Freight
Tools for a replacement.
Page 3For technical questions, please call 1-800-444-3353.Item 67599
General safety
1. Make sure the area in which the Carrier
is assembled is clean and well lit.
Cluttered or dark areas invite accidents.
2. Keep children and bystanders away
while assembling the Carrier.
3. Stay alert, watch what you are doing
and use common sense when using the
Carrier. Do not use the Carrier while
you are tired or under the influence of
drugs, alcohol or medication. A moment
of inattention while using the Carrier
may result in serious personal injury.
Carrier use and care
1. Use the correct Carrier for your
application. The correct Carrier will
do the job better and safer at the
rate for which it was designed.
2. Store the Carrier out of reach of children
and do not allow people unfamiliar
with the Carrier or these instructions
to use the Carrier. Use of carrier by
untrained people may not be safe.
3. Maintain the Carrier. Check for
misalignment or binding of moving
parts, breakage of parts and any
other condition that may affect the
Carrier’s operation. If damaged,
have the Carrier repaired before
use. Many accidents are caused
by poorly maintained equipment.
4. Use this Carrier in accordance with
these instructions and in the manner
intended for this particular type of
product, taking into account the area
conditions and the task to be performed.
Use of this Carrier for operations
different from those intended could
result in a hazardous situation.
Service
Have this Carrier serviced by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the Carrier is maintained.
SAVE THESE INSTRUCTIONS.
Page 4 For technical questions, please call 1-800-444-3353. Item 67599
Assembly
Read the ENTIRE IMPORTANT SAFETY INFORMATION section
at the beginning of this manual including all text under
subheadings therein before set up or use of this product.
Note: For additional information regarding the parts listed in the following pages, refer to
Parts List and Assembly Diagram on page 11.
1. Set Bed (1) on a flat, secure work area able to support weight of Carrier.
2. Use Small Bolts (12) and Nuts (13) to connect all supports (5-8) to Bed. See Figure 1.
Note: Do not fully tighten Bolts and
make sure Supports With Reflector
(6) are on the same side.
3. Use the small Bolts and Nuts to connect the U-Brace (2) to the top of the Supports.
See Figure 2.
Note: Make sure the ends of the
U-Brace face the open side.
4. Use a wrench and/or
screwdriver (sold separately)
to tighten all Bolts and Nuts
until the Carrier Bed frame is
secure.
Figure 1
6
7
5
6
5
7
78
1
Figure 2
2
Page 5For technical questions, please call 1-800-444-3353.Item 67599
5. With assistance, flip over the Carrier Bed frame and use Medium Bolts (14), Washers
(15, 23) and Nuts (16) to fasten the Hitch Bar (9) to the Carrier Bed’s underside.
See Figure 3.
Note: Make sure the Hitch Bar
extension is OPPOSITE the side
of the Bed with the reflectors.
Note: Make sure all Bolts are
tightened securely.
6. Use the Washers (20) and Nuts (21) to attach a Tie-Down Hook (19) to each corner of
the Carrier Bed. See Figure 4.
Note: Make sure all Bolts are
tightened securely.
Figure 3
9
Figure 4
19
20
21
Page 6 For technical questions, please call 1-800-444-3353. Item 67599
7. Use Large Bolts (17) and Lock Nuts (18) to attach Ramp (3) to open side of the Carrier
Bed. See Figure 5.
Note: Do not overtighten
connections. There should be
enough give to allow Ramp to pivot
freely.
8. Swing the Ramp up, and use the Pins (4) and Lock Pins (22) to lock Ramp in upright
position. See Figure 6.
9. With assistance, lift Carrier
up and insert Hitch Bar into
vehicle’s receiver hitch. Align
hole in Hitch Bar with hole
in vehicle’s receiver hitch.
10. Insert Hitch Pin (10) through
holes in both hitches and
fasten in place using
Hitch Lock Pin (11).
Figure 5
3
Figure 6
4
22
Page 7For technical questions, please call 1-800-444-3353.Item 67599
Functions
Figure A: Components
Lock Pin
Lock Pin
Ramp
Tie Down Hooks R-Pin
R-Pin
Carrier Bed
U-Brace
Hitch Bar
Page 8 For technical questions, please call 1-800-444-3353. Item 67599
Operation Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the
beginning of this document including all text under subheadings therein
before set up or use of this product.
To prevent serious injury and DEATH:
Do not ride a vehicle while loading or unloading. An unbalanced vehicle being
ridden up a steep angle can tip over, causing serious injury or DEATH.
Make sure the vehicle is turned off and in gear or park, with the
emergency brake engaged and the wheels blocked before loading.
Make sure the Carrier is secured onto the vehicle.
Make sure the Carrier is clean and dry before loading.
Loading
WARNING! Do not exceed this Carrier’s
maximum weight capacity of 500 pounds.
1. Once the Carrier is fastened to the
hitch, lower the Ramp. Do this by
removing the Lock Pins and Pins,
which unlocks the Ramp from the
Body. Lower the Ramp to the ground.
CAUTION! Make sure the feet of
the Ramp rest flat on a solid, level
surface during the loading and
unloading of Wheelchair or Scooter.
Note: Loading from a raised, flat,
level surface, like a sidewalk, will
lessen the angle of the ramp and
make loading easier and safer.
2. With assistance, push the Wheelchair/
Scooter up the Ramp and onto
the Carrier Bed. Make sure the
load is centered on the Carrier.
3. Secure Wheelchair/Scooter in place
using appropriate tie-downs or ropes
(sold separately). Fasten tie-downs
or ropes to the Tie-Down Hooks.
4. Once the load is secure, swing
the Ramp up. Lock in place,
using Lock Pins and Pins.
5. The load (wheelchair, scooter, ATV,
etc.) can now be transported.
NOTICE! Contact local Department of
Transportation to verify all safety guidelines
are being followed before transporting load.
WARNING! Do not transport without
locking Ramp to Carrier.
DANGER! Do not ride on Wheelchair,
Scooter or other vehicle that is being
loaded onto or unloaded from the Carrier.
Page 9For technical questions, please call 1-800-444-3353.Item 67599
Unloading
1. To unload the vehicle, untie the tie-
downs or ropes from the Tie Down
Hooks, unlock and lower the Ramp.
2. With assistance, carefully unload
Wheelchair/Scooter from Carrier. Once
Carrier has been unloaded, raise Ramp
and lock back into place. See Figure 7.
Figure 7
3
1
Page 10 For technical questions, please call 1-800-444-3353. Item 67599
Maintenance and Servicing
Procedures not specifically explained in this manual must
be performed only by a qualified technician.
TO PREVENT SERIOUS INJURY:
Remove load from the Carrier before performing any maintenance or service.
Do not use damaged equipment. If the Carrier is damaged
have the problem corrected before further use.
Cleaning, Maintenance, and Lubrication
1. BEFORE EACH USE, inspect
the general condition of the
Carrier. Check for:
• loose hardware,
• misalignment or binding of parts,
• cracked, bent, or broken parts, and
• any other condition that may
affect its safe operation.
2. Clean the Carrier after each use.
Make sure dirt, oil, grease, and
debris are not on the Carrier.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST IN THIS
DOCUMENT AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE
OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/
OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY
THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR
HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR
ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Page 11For technical questions, please call 1-800-444-3353.Item 67599
Parts List and Assembly Diagram
Part Description Qty
1 Bed 1
2 U-Brace 1
3 Ramp 1
4 Pin 2
5 Medium Support 4
6 Support With Reflector 2
7 Small Support 6
8 Large Support 2
9 Hitch Bar 1
10 Hitch Pin 1
11 Hitch Lock Pin 3
12 Small Bolt (M5x12) 46
Part Description Qty
13 Lock Nut (M5) 46
14 Medium Bolt (M6x45) 10
15 Washer (ø6) 20
16 Lock Nut (M6) 10
17 Large Bolt (M8 x 30) 2
18 Lock Nut (M8) 2
19 Tie Down Hook 4
20 Washer (ø6) 4
21 Nut (M6) 4
22 Lock Pin 2
23 Large Washer 6
1
2
3
4, 22
5
6
7
8
9
10
13, 12
11
17, 18
19, 20, 21
14, 15, 16, 23
Record Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed for illustration purposes only, and
are not available individually as replacement parts.
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality
and durability standards, and warrants to the original purchaser that this product is free from
defects in materials and workmanship for the period of 90 days from the date of purchase.
This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence
or accidents, repairs or alterations outside our facilities, criminal activity, improper installation,
normal wear and tear, or to lack of maintenance. We shall in no event be liable for death,
injuries to persons or property, or for incidental, contingent, special or consequential damages
arising from the use of our product. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation of exclusion may not apply to you.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation
charges prepaid. Proof of purchase date and an explanation of the complaint must accompany
the merchandise. If our inspection verifies the defect, we will either repair or replace
the product at our election or we may elect to refund the purchase price if we cannot readily
and quickly provide you with a replacement. We will return repaired products at our expense,
but if we determine there is no defect, or that the defect resulted from causes not within
the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also
have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
