Harbor Freight 5 Amp Heavy Duty Tool Free Variable Speed Orbital Jig Saw Product Manual
Manual for the 62422 5 Amp Heavy Duty Tool-Free Variable Speed Orbital Jig Saw 62422 5 Amp Heavy Duty Tool-Free Variable Speed Orbital Jig Saw
2015-05-27
: Harbor-Freight Harbor-Freight-5-Amp-Heavy-Duty-Tool-Free-Variable-Speed-Orbital-Jig-Saw-Product-Manual-723116 harbor-freight-5-amp-heavy-duty-tool-free-variable-speed-orbital-jig-saw-product-manual-723116 harbor-freight pdf
Open the PDF directly: View PDF 
.
Page Count: 16
| Download | |
| Open PDF In Browser | View PDF |
Owner’s Manual & Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference. ORBITAL (Blade sold separately) REV 14g Visit our website at: http://www.harborfreight.com Email our technical support at: productsupport@harborfreight.com When unpacking, make sure that the product is intact and undamaged. If any parts are missing or broken, please call 1-888-866-5797 as soon as possible. Copyright© 2014 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included. Read this material before using this product. Failure to do so can result in serious injury. SAVE THIS MANUAL. Important Safety Information In this manual, on the labeling, and all other information provided with this product: This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury. WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTION, used with the safety alert symbol, indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. NOTICE is used to address practices not related to personal injury. CAUTION, without the safety alert symbol, is used to address practices not related to personal injury. General Power Tool Safety Warnings WARNING Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term ″power tool″ in the warnings refers to your mains‑operated (corded) power tool. Page 2 1. Work area safety a. Keep work area clean and well lit. Cluttered or dark areas invite accidents. b. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. c. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. 2. Electrical safety a. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with grounded power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. b. Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded. c. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. d. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. e. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. f. If operating a power tool in a damp location is unavoidable, use a Ground Fault Circuit Interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric shock. For technical questions, please call 1-888-866-5797. Item 62422 3. Personal safety 4. Power tool use and care a. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. b. Use personal protective equipment. Always wear eye protection. Safety equipment such as a dust mask, non-skid safety shoes, a hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. c. Prevent unintentional starting. Ensure the switch is in the off‑position before connecting to power source, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents. d. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f. Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts. g. If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of these devices can reduce dust‑related hazards. h. Only use safety equipment that has been approved by an appropriate standards agency. Unapproved safety equipment may not provide adequate protection. Eye protection must be ANSI-approved and breathing protection must be NIOSH-approved for the specific hazards in the work area. Item 62422 a. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. c. Disconnect the plug from the power source before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. d. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. e. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. 5. Service a. Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. For technical questions, please call 1-888-866-5797. Page 3 Jigsaw Safety Warnings 1. Hold power tool by insulated gripping surfaces when performing an operation where cutting tool may contact hidden wiring or its own cord. Contact with a ″live″ wire will make exposed metal parts of the tool ″live″ and shock the operator. 2. Use clamps or another practical way to secure and support the work piece to a stable platform. Holding the work by hand or against your body leaves it unstable and may lead to loss of control. 3. Maintain labels and nameplates on the tool. These carry important safety information. If unreadable or missing, contact Harbor Freight Tools for a replacement. 4. Avoid unintentional starting. Prepare to begin work before turning on the tool. 5. Do not lay the tool down until it has come to a complete stop. Moving parts can grab the surface and pull the tool out of your control. 6. When using a handheld power tool, maintain a firm grip on the tool with both hands to resist starting torque. 7. Do not leave the tool unattended when it is plugged into an electrical outlet. Turn off the tool, and unplug it from its electrical outlet before leaving. 8. This product is not a toy. Keep it out of reach of children. 9. People with pacemakers should consult their physician(s) before use. Electromagnetic fields in close proximity to heart pacemaker could cause pacemaker interference or pacemaker failure. In addition, people with pacemakers should: • Avoid operating alone. • Do not use with power switch locked on. • Properly maintain and inspect to avoid electrical shock. • Any power cord must be properly grounded. Ground Fault Circuit Interrupter (GFCI) should also be implemented – it prevents sustained electrical shock. Page 4 10. WARNING: The cord of this product contains lead, a chemical known to the State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling. (California Health & Safety Code § 25249.5, et seq.) 11. WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities, contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints • Crystalline silica from bricks and cement or other masonry products • Arsenic and chromium from chemically treated lumber Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. (California Health & Safety Code § 25249.5, et seq.) 12. The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Vibration Safety This tool vibrates during use. Repeated or long‑term exposure to vibration may cause temporary or permanent physical injury, particularly to the hands, arms and shoulders. To reduce the risk of vibration-related injury: For technical questions, please call 1-888-866-5797. Item 62422 1. Anyone using vibrating tools regularly or for an extended period should first be examined by a doctor and then have regular medical check-ups to ensure medical problems are not being caused or worsened from use. Pregnant women or people who have impaired blood circulation to the hand, past hand injuries, nervous system disorders, diabetes, or Raynaud’s Disease should not use this tool. If you feel any symptoms related to vibration (such as tingling, numbness, and white or blue fingers), seek medical advice as soon as possible. 2. Do not smoke during use. Nicotine reduces the blood supply to the hands and fingers, increasing the risk of vibration-related injury. 3. Wear suitable gloves to reduce the vibration effects on the user. 4. Use tools with the lowest vibration when there is a choice. 5. Include vibration-free periods each day of work. 6. Grip tool as lightly as possible (while still keeping safe control of it). Let the tool do the work. 7. To reduce vibration, maintain the tool as explained in this manual. If any abnormal vibration occurs, stop use immediately. SAVE THESE INSTRUCTIONS. Grounding TO PREVENT ELECTRIC SHOCK AND DEATH FROM INCORRECT GROUNDING WIRE CONNECTION: Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with the tool. Never remove the grounding prong from the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have it repaired by a service facility before use. If the plug will not fit the outlet, have a proper outlet installed by a qualified electrician. Double Insulated Tools: Tools with Two Prong Plugs Outlets for 2-Prong Plug 1. Tools marked “Double Insulated” do not require grounding. They have a special double insulation system which satisfies OSHA requirements and complies with the applicable standards of Underwriters Laboratories, Inc., the Canadian Standard Association, and the National Electrical Code. 2. Double insulated tools may be used in either of the 120 volt outlets shown in the preceding illustration. (See Outlets for 2-Prong Plug.) Item 62422 For technical questions, please call 1-888-866-5797. Page 5 3. The smaller the gauge number of the wire, the greater the capacity of the cord. For example, a 14 gauge cord can carry a higher current than a 16 gauge cord. (See Table A.) 4. When using more than one extension cord to make up the total length, make sure each cord contains at least the minimum wire size required. (See Table A.) 5.1 – 7.0 18 16 14 12 12 7.1 – 12.0 18 14 12 10 12.1 – 16.0 14 12 10 16.1 – 20.0 12 10 * Based on limiting the line voltage drop to five volts at 150% of the rated amperes. Symbology 5. If you are using one extension cord for more than one tool, add the nameplate amperes and use the sum to determine the required minimum cord size. (See Table A.) Double Insulated 6. If you are using an extension cord outdoors, make sure it is marked with the suffix “W-A” (“W” in Canada) to indicate it is acceptable for outdoor use. Underwriters Laboratories, Inc. 7. Make sure the extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified electrician before using it. 150´ 100´ (at full load) 75´ 2. As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage, resulting in loss of power and possible tool damage. (See Table A on page 6.) Table A: RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS* (120/240 VOLT) EXTENSION CORD NAMEPLATE LENGTH AMPERES 50´ 1. Grounded tools require a three wire extension cord. Double Insulated tools can use either a two or three wire extension cord. 8. Protect the extension cords from sharp objects, excessive heat, and damp or wet areas. 25´ Extension Cords Canadian Standards Association VAC A Volts Alternating Current Amperes WARNING marking concerning Risk of Eye Injury. Wear ANSI‑approved safety goggles with side shields. Read the manual before set-up and/or use. WARNING marking concerning Risk of Electric Shock. Properly connect power cord to appropriate outlet. Page 6 For technical questions, please call 1-888-866-5797. Item 62422 Specifications Electrical Rating 120VAC / 60Hz / 5A Footplate Tilt 0-45°, left or right Cutting Speed 0-3000 SPM Blade Type T-Shank Stroke Length 3/4″ Max. Capacity 2-1/4″ (wood) 4006094 Instructions for Putting into Use Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn the Power Switch of the tool off and unplug the tool from its electrical outlet before assembling or making any adjustments to the tool. Note: For additional information regarding the parts listed in the following pages, refer to Parts List and Assembly Diagram on page 14. Speed Switch Trigger Lock Trigger (17) Hex Key Orbital Mode Level (16) Dust Chute Connector Blade Cover (14) Blade Release Lever Base Plate (19) Blade (sold separately) Item 62422 Roller Guide For technical questions, please call 1-888-866-5797. Page 7 Blade Installation 1. Refer to the Chart below to select the proper Saw Blade for the material being cut. BLADE SELECTION AND SUITABLE SPEED Material TPI Speed Soft Wood 6 6 Hardwood 6 5 Plastic 12 4~6 Aluminum 12 3~6 Steel 24 2~4 Tile 24 1~3 Glass 32 1~3 Leather (Knife Edge) 4~6 Rubber (Knife Edge) 4~6 WARNING! Wear ANSI-approved safety goggles and heavy-duty work gloves when changing blade. 2. Once the proper blade (sold separately) is selected, lift the Blade Cover (14) up to access the Blade Release Lever. See Figure 1, below. Blade Cover (14) Blade Release Lever Blade Collet Roller Guide Figure 1 3. Pull Blade Release Lever counterclockwise to open Blade Collet. 4. With the blade teeth facing FORWARD, inset blade into blade holding Collet as far as it will go. WARNING! Make sure blade’s back edge is set against the roller guide. 5. Release the blade release lever. Pull on blade until blade Collet snaps blade into place. Page 8 For technical questions, please call 1-888-866-5797. Item 62422 Operating Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn the Power Switch of the tool off and unplug the tool from its electrical outlet before adjusting tool or installing accessories. Work Piece and Work Area Set Up 2. The settings are: a. I = Straight line cutting (for plastics and mild steel) 1. Designate a work area that is clean and well-lit. The work area must not allow access by children or pets to prevent distraction and injury. b. II = Small orbit (for aluminum and hard wood) 2. Route the power cord along a safe route to reach the work area without creating a tripping hazard or exposing the power cord to possible damage. The power cord must reach the work area with enough extra length to allow free movement while working. d. IV = Large orbit (for fast cutting wood and plywood) 3. Secure loose work pieces using a vise or clamps (not included) to prevent movement while working. 4. There must not be objects, such as utility lines, nearby that will present a hazard while working. c. III = Medium orbit (for wood, plywood and fast cutting of aluminum) Adjusting Jigsaw Speed 1. The Jigsaw’s speed can be adjusted between 500 and 3,000 strokes per minutes. 2. To adjust speed, turn the Speed Switch from 1 (the slowest speed) to 6 (the fastest speed). See Figure 3, below. Speed Switch Selecting Cutting Mode 1. The Jigsaw comes with four cutting modes (three cutting settings and 1 straight cutting mode). To change cutting mode, adjust the Orbital Mode Lever (16). See Figure 2, below. Orbital Mode Lever (16) Figure 3 3. Use higher speeds to cut work pieces faster. NOTICE: Refer to the Blade Selection chart on page 7 to verify you are using the correct speed with the appropriate blade. Otherwise blade damage can occur. Figure 2 Item 62422 For technical questions, please call 1-888-866-5797. Page 9 General Operating Instructions 1. Plug the Power Cord into the nearest 120 volt, grounded, electrical outlet. 2. Position the saw blade of the Jigsaw about 1/2” from the beginning cut line on the work piece. Do not allow the saw blade to come in contact with the work piece. 3. Squeeze the Trigger (17) to turn on the Jigsaw. If operating the Jigsaw for an extended period of time, press the Trigger Lock to lock the Trigger in its “ON” position. See Figure 4, below. Trigger (17) Figure 4 Page 10 Trigger Lock 4. Allow the Saw Blade to stroke at full speed before slowly feeding it into the work piece. 5. Make sure to hold the Jigsaw firmly with both hands to avoid kickback. Then, finish making the cut. Dust Chute 1. The Jigsaw is supplied with a Dust Chute adapter for a vacuum. It is attached to the Dust Chute Connector located at the back end of the housing. 2. To fasten the Dust Chute (sold separately) in place, align the pins on Dust Chute with slots in Connector. Push Dust Chute in and turn clockwise to lock. See Figure 5, below. Connector Dust Chute For technical questions, please call 1-888-866-5797. Figure 5 Item 62422 Bevel and Metal Cutting 1. Use the included Hex Key to loosen the Cap Screw (21) on the bottom of the Base Plate (19). Tilt the base, allowing for bevel cuts between 0 and 45°. 2. Retighten the Cap Screw once the desired angle is reached. 3. For metal cutting, be sure to use a coolant such as cutting oil during use. Failure to add coolant will lead to greater blade wear. If desired, grease the underside of the work piece in place of adding coolant. 4. When finished with the Jigsaw, unlock and release the Trigger to stop the Jigsaw. Wait until the Saw Blade stops completely. Then, remove the Jigsaw from the work piece. 5. To prevent accidents disconnect the power cord after use. Clean, then store the tool indoors out of children’s reach. Item 62422 For technical questions, please call 1-888-866-5797. Page 11 Maintenance and Servicing Procedures not specifically explained in this manual must be performed only by a qualified technician. TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Unlock and release Trigger and unplug tool from its electrical outlet before performing any inspection, maintenance, or cleaning procedures. TO PREVENT SERIOUS INJURY FROM TOOL FAILURE: Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use. Page 12 Cleaning, Maintenance, and Lubrication 1. BEFORE EACH USE, inspect the general condition of the tool. Check for loose hardware, misalignment or binding of moving parts, cracked or broken parts, damaged electrical wiring, and any other condition that may affect its safe operation. 2. Inspect the Saw Blade. Replace with a new Saw Blade when needed. 3. AFTER USE, wipe external surfaces of the tool with clean cloth. 4. WARNING! If the supply cord of this power tool is damaged, it must be replaced only by a qualified service technician. For technical questions, please call 1-888-866-5797. Item 62422 Troubleshooting Problem Possible Causes Tool will not start. 1. Cord not connected. 2. No power at outlet. Tool operates slowly. Performance decreases over time. Excessive noise or rattling. Overheating. Likely Solutions 1. Check that cord is plugged in. 2. Check power at outlet. If outlet is unpowered, turn off tool and check circuit breaker. If breaker is tripped, make sure circuit is right capacity for tool and circuit has no other loads. 3. Internal damage or wear. 3. Have technician service tool. (Carbon brushes or switch, for example.) Extension cord too long Eliminate use of extension cord. or wire size too small. If an extension cord is needed, use shorter/ heavier gauge cord. See Extension Cords in Grounding section on page 5. 1. Accessory dull 1. Keep cutting accessories sharp. or damaged. Replace as needed. 2. Carbon brushes worn or damaged. Internal damage or wear. (Carbon brushes or bearings, for example.) 1. Forcing tool to work too fast. 2. Have qualified technician replace brushes. 2. Accessory misaligned. 2. Check and correct accessory to fence and/or table alignment. 3. Accessory dull or damaged. 3. Keep cutting accessories sharp. Replace as needed. 4. Blocked motor housing vents. 4. Wear ANSI-approved safety goggles and NIOSH‑approved dust mask/respirator while blowing dust out of motor using compressed air. 5. Motor being strained by long or small diameter extension cord. 5. Eliminate use of extension cord. If an extension cord is needed, use one with the proper diameter for its length and load. See Extension Cords in Grounding section on page 5. Have technician service tool. 1. Allow tool to work at its own rate. Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect power supply before service. Item 62422 For technical questions, please call 1-888-866-5797. Page 13 Parts List and Assembly Diagram PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. Parts List Part 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Description Cutting Mode Selector Wring Spring Steel Ball Washer Board Ring Dowel Left Cover Left Half Housing Cord Guard Power Cord Cord Clip Screw St4×16 Axle Positioning Pin Blade Cover Guard Rod Orbital Mode Level Trigger Square Nut M4 Base Plate Washer Board Cap Screw Base Plate Sheath Stator Bearing 607Z Qty 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 Part 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 Description Rotor Carbon Brush Copper Brush Brush Holder Bearing 608Z Center Support Axle Bearing K060913.5 Balance Plate Axle Slip Gutter Balance Block Gear Washer Board Washer Board Guide Roller Slide Rod Combination Spring Slide Mass Speed Control Dial Right Half Housing Screw St4×20 Screw St4×38 Right Cover Right Name Plate Qty 1 2 2 2 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 8 1 1 1 Record Product’s Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Page 14 For technical questions, please call 1-888-866-5797. Item 62422 5 2 40 41 42 Assembly Diagram 4 3 1 6 17 7 39 38 8 33 37 36 14 11 10 9 35 15 12 34 32 31 30 16 29 13 43 28 27 26 44 25 24 45 46 18 19 20 21 22 23 48 47 Page 15 For technical questions, please call 1-888-866-5797. Item 62422 Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS. To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. 3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : Yes Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.6-c011 79.156289, 2014/03/31-23:39:12 Instance ID : uuid:f37a4fc5-b7b4-894e-bfa0-68624264403a Original Document ID : adobe:docid:indd:2947f79c-bab0-11df-a4dc-d1b6dbadcc65 Document ID : xmp.id:b386bad3-bc4d-4650-a3d7-28e3388a8f45 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:fdeb3343-838c-429d-9c48-b1d3c208f62a Derived From Document ID : xmp.did:CC2D317D072068118C14809467926F1D Derived From Original Document ID: adobe:docid:indd:2947f79c-bab0-11df-a4dc-d1b6dbadcc65 Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CC 2014 (Macintosh) History Changed : / History When : 2014:07:23 12:04:12-07:00 Create Date : 2014:07:23 12:04:12-07:00 Modify Date : 2014:07:23 12:04:22-07:00 Metadata Date : 2014:07:23 12:04:22-07:00 Creator Tool : Adobe InDesign CC 2014 (Macintosh) Format : application/pdf Creator : Adobe Rights : Copyright©2011 by Harbor Freight Tools®. All rights reserved. No portion of this document or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Web Statement : http://www.harborfreight.com Marked : True Producer : Adobe PDF Library 11.0 Trapped : False Page Count : 16 Author : AdobeEXIF Metadata provided by EXIF.tools