Harbor Freight 69269 Owner S Manual

: Harbor-Freight Harbor-Freight-69269-Owner-S-Manual harbor-freight-69269-owner-s-manual harbor-freight pdf

Open the PDF directly: View PDF .
Page Count: 16

Visit our website at: http://www.harborfreight.com

Email our technical support at: tech@harborfreight.com

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

Copyright© 2011 by Harbor Freight Tools®. All rights reserved.

No portion of this manual or any artwork contained herein may be reproduced in

any shape or form without the express written consent of Harbor Freight Tools.

Diagrams within this manual may not be drawn proportionally. Due to continuing

improvements, actual product may differ slightly from the product described herein.

Tools required for assembly and service may not be included.

When unpacking, make sure that the product is intact

and undamaged. If any parts are missing or broken,

please call 1-800-444-3353 as soon as possible.

Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating,

inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual

near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and

the receipt in a safe and dry place for future reference.

Owner’s Manual & Safety Instructions

ITEM 69269

3 GAL oilless

air compressor

REV 11l

Page 2 For technical questions, please call 1-800-444-3353. Item 69269

SAFETY OPERATION MAINTENANCESETUP

Table of Contents

Safety ......................................................... 2

Setup .......................................................... 6

Specifications ............................................. 6

Operation ................................................... 10

Maintenance .............................................. 12

Parts List and Diagram .............................. 14

Warranty .................................................... 16

WARNING SYMBOLS AND DEFINITIONS

This is the safety alert symbol. It is used to alert you to potential personal injury hazards.

Obey all safety messages that follow this symbol to avoid possible injury or death.

Indicates a hazardous situation which, if not avoided,

will result in death or serious injury.

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

Addresses practices not related to personal injury.

Page 3For technical questions, please call 1-800-444-3353.Item 69269

SAFETYOPERATIONMAINTENANCE SETUP

IMPORTANT SAFETY INFORMATION

General Safety Warnings

WARNING Read all safety warnings and instructions.

Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible

conditions and situations that may occur. It must be understood by the operator that common sense

and caution are factors which cannot be built into this product, but must be supplied by the operator.

1. Work area safety

a. Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b. Do not operate the Compressor in explosive

atmospheres, such as in the presence

of flammable liquids, gases or dust.

Compressor motors produce sparks

which may ignite the dust or fumes.

c. Keep children and bystanders away

from an operating compressor.

2. Electrical safety

a. Compressor plugs must match the outlet.

Never modify the plug in any way.

Do not use any adapter plugs with grounded

compressors. Standard plugs and matching

outlets will reduce risk of electric shock.

b. Do not expose compressor to rain or wet

conditions. Water entering a compressor

will increase the risk of electric shock.

c. Do not abuse the cord. Never use the

cord for unplugging the compressor.

Keep cord away from heat, oil, sharp edges

or moving parts. Damaged or entangled

cords increase the risk of electric shock.

3. Personal safety

a. Stay alert, watch what you are doing and

use common sense when operating this

compressor. Do not use this compressor

while you are tired or under the influence

of drugs, alcohol or medication. A moment

of inattention while operating a compressor

may result in serious personal injury.

b. Use personal protective equipment.

Always wear ANSI-approved eye

protection during setup and use.

c. Prevent unintentional starting. Ensure the

switch is in the off-position before connecting

to power source or moving the compressor.

4. Compressor use and care

a. Do not use the compressor if the switch

does not turn it on and off. Any compressor

that cannot be controlled with the switch

is dangerous and must be repaired.

b. Disconnect the plug from the power source

before making any adjustments, changing

accessories, or storing the compressor.

Such preventive safety measures reduce the

risk of starting the compressor accidentally.

c. Store an idle compressor out of the reach

of children and do not allow persons

unfamiliar with the compressor or these

instructions to operate it. A compressor is

dangerous in the hands of untrained users.

d. Maintain the compressor. Keep the

compressor clean for better and safer

performance. Follow instructions for

lubricating and changing accessories.

Keep dry, clean and free from oil and grease.

Check for misalignment or binding of moving

parts, breakage of parts and any other

condition that may affect the compressor’s

operation. If damaged, have the compressor

repaired before use. Many accidents are

caused by a poorly maintained compressor.

e. Use the compressor in accordance with

these instructions, taking into account

the working conditions and the work to

be performed. Use of the compressor for

operations different from those intended

could result in a hazardous situation.

5. Service

a. Have your compressor serviced by a

qualified repair person using only identical

replacement parts. This will ensure that the

safety of the compressor is maintained.

Page 4 For technical questions, please call 1-800-444-3353. Item 69269

SAFETY OPERATION MAINTENANCESETUP

Air Compressor Safety Warnings

1. Risk of fire or explosion - do not spray flammable

liquid in a confined area or towards a hot surface.

Spray area must be well-ventilated. Do not

smoke while spraying or spray where spark or

flame is present. Arcing parts - keep compressor

at least 20 feet away from explosive vapors,

such as when spraying with a spray gun.

2. Risk of bursting - do not adjust regulator higher

than marked maximum pressure of attachment.

3. Risk of injury - do not direct air

stream at people or animals.

4. Do not use to supply breathing air.

5. Do not leave compressor unattended

for an extended period while plugged in.

Unplug compressor after working.

6. Keep compressor well-ventilated.

Do not cover compressor during use.

7. Drain Tank daily and after use. Internal rust causes

tank failure and explosion.

8. Do not remove the valve cover or

adjust internal components.

9. Compressor head gets hot during operation.

Do not touch it or allow children nearby during

or immediately following operation.

10. Do not use the air hose to move the compressor.

11. Release the pressure in the

storage tank before moving.

12. The use of accessories or attachments not

recommended by the manufacturer may

result in a risk of injury to persons.

13. All air line components, including hoses, pipe,

connectors, filters, etc., must be rated for a minimum

working pressure of 150 PSI, or 150% of the

maximum system pressure, whichever is greater.

14. USE OF AN EXTENSION CORD IS NOT

RECOMMENDED. If you choose to use an

extension cord, use the following guidelines:

TABLE A: RECOMMENDED MINIMUM WIRE

GAUGE FOR EXTENSION CORDS

(120 VOLT)

NAMEPLATE

AMPERES

(at full load)

EXTENSION CORD

LENGTH

25′ 50′ 100′ 150′

0 – 6 18 16 16 14

6.1 – 10 18 16 Do not use.

10.1 – 12 16 16 Do not use.

12.1 – 16 14 12 Do not use.

a. Make sure your extension cord

is in good condition.

b. Be sure to use an extension cord which is heavy

enough to carry the current your product will draw.

An undersized cord will cause a drop in line

voltage resulting in loss of power and overheating.

Table A shows the correct size to use depending

on cord length and nameplate ampere rating.

If in doubt, use the next heavier gauge. The

smaller the gauge number, the heavier the cord.

15. Industrial applications must follow OSHA guidelines.

16. Maintain labels and nameplates on the

compressor. These carry important safety

information. If unreadable or missing, contact

Harbor Freight Tools for a replacement.

17. This product is not a toy.

Keep it out of reach of children.

18. Operate unit on level surface. Check oil level

daily and fill to marked level if needed.

19. People with pacemakers should consult their

physician(s) before use. Electromagnetic fields in

close proximity to heart pacemaker could cause

pacemaker interference or pacemaker failure.

20. WARNING: The brass components of

this product contain lead, a chemical

known to the State of California to cause

birth defects (or other reproductive harm).

(California Health & Safety code § 25249.5, et seq.)

SAVE THESE INSTRUCTIONS.

Page 5For technical questions, please call 1-800-444-3353.Item 69269

SAFETYOPERATIONMAINTENANCE SETUP

Grounding

TO PREVENT ELECTRIC SHOCK AND DEATH

FROM INCORRECT GROUNDING WIRE CONNECTION:

Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded.

Do not modify the power cord plug provided with the compressor.

Never remove the grounding prong from the plug. Do not use the compressor if the power cord or plug is

damaged. If damaged, have it repaired by a service facility before use. If the plug will not fit the outlet, have a

proper outlet installed by a qualified electrician.

110-120 V~ Grounded Compressors: Compressors with Three Prong Plugs

1. In the event of a malfunction or breakdown,

grounding provides a path of least resistance for

electric current to reduce the risk of electric shock.

This compressor is equipped with an electric

cord having an equipment-grounding conductor

and a grounding plug. The plug must be

plugged into a matching outlet that is properly

installed and grounded in accordance

with all local codes and ordinances.

2. Do not modify the plug provided –

if it will not fit the outlet, have the proper

outlet installed by a qualified electrician.

3. Improper connection of the equipment-grounding

conductor can result in a risk of electric shock.

The conductor with insulation having an outer

surface that is green with or without yellow

stripes is the equipment-grounding conductor.

If repair or replacement of the electric cord or

plug is necessary, do not connect the equipment-

grounding conductor to a live terminal.

4. Check with a qualified electrician or service

personnel if the grounding instructions are

not completely understood, or if in doubt as to

whether the compressor is properly grounded.

5. Use only 3-wire extension cords that have

3-prong grounding plugs and 3-pole receptacles

that accept the compressor’s plug.

6. Repair or replace damaged or worn cord immediately.

125 V~ 3-Prong Plug and Outlet

(for up to 125 V~ and up to 15 A)

Grounding

Pin

7. This compressor is intended for use on a

circuit that has an outlet that looks like the

one illustrated above in 125 V~ 3-Prong Plug

and Outlet. The compressor has a grounding

plug that looks like the plug illustrated above

in 125 V~ 3-Prong Plug and Outlet.

8. The outlet must be properly installed and grounded

in accordance with all codes and ordinances.

9. Do not use an adapter to connect this

compressor to a different outlet.

Symbology

PSI Pounds per square inch of pressure

CFM Cubic Feet per Minute flow

SCFM Cubic Feet per Minute flow

at standard conditions

NPT National pipe thread, tapered

NPS National pipe thread, straight

Double Insulated

Canadian Standards Association

Underwriters Laboratories, Inc.

V~ Volts Alternating Current

AAmperes

Page 6 For technical questions, please call 1-800-444-3353. Item 69269

SAFETY OPERATION MAINTENANCESETUP

Specifications

Electrical Rating 120V~ / 60Hz / 2.6A

Air Outlet Size 1/4″ -18 NPT

Air Pressure Shut-off 100 PSI

Restart 85 PSI

Air Tank Capacity 3 Gallons

Air Flow Capacity 0.6 CFM @ 90 PSI

1.0 CFM @ 40 PSI

Sound Level 88 dB @ 1m

227847

Instructions for putting into use

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this

manual including all text under subheadings therein before set up or use of this product.

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:

Turn the Power Switch “OFF” and unplug the Air Compressor from its electrical

outlet before assembling or making any adjustments to the compressor.

Note: For additional information regarding the parts listed in the following pages,

refer to the Assembly Diagram near the end of this manual.

Functions

Figure A

Outlet Pressure

Gauge (70)

Tank Pressure

Gauge (26)

Safety Valve (25)

Pressure Regulator (24)

Drain Valve (54)

ON/OFF Power Switch (45)

Fuse

Page 7For technical questions, please call 1-800-444-3353.Item 69269

SAFETYOPERATIONMAINTENANCE SETUP

Assembly/Mounting

1. Align the two mounting holes in the Handle

with the two threaded mounting holes in the

Bracket on the Air Tank. Secure the Handle

to the Air Tank using the two Screws.

2. Break in the new Air Compressor as follows:

a. Turn the Power Switch off and unplug the unit.

Insert a male coupler (sold separately)

into the female Quick Coupler and fully

open all regulators and valves.

b. Plug in the Power Cord.

c. Turn the Power Switch ON.

d. Let the unit run for 30 minutes.

Air will expel freely through the Coupler.

e. Turn the Power Switch OFF.

f. Unplug the Power Cord and

remove the male coupler.

3. Connect a regulator valve, an inline shut off valve

and a 1/4″ NPT air hose to the Quick Coupler

(all sold separately). The air hose must be long

enough to reach the work area with enough extra

length to allow free movement while working.

Note: An in-line shutoff ball valve is an important

safety device because it controls the air supply even

if the air hose is ruptured. The shutoff valve should

be a ball valve because it can be closed quickly.

4. Depending on the tool which you will be

using with this compressor, you may need to

incorporate additional components, such as an

in-line oiler, a filter, or a dryer (all sold separately),

as shown on Figure B on page 8 and

Figure C on page 9. Consult your air

tool’s manual for needed accessories.

Page 8 For technical questions, please call 1-800-444-3353. Item 69269

SAFETY OPERATION MAINTENANCESETUP

Figure B: Portable Air Supply Setup

G

A

E

E H

F

B

Non-lubricated

Tools

Lubricated

Tools

A

B

C

C

DA

Description Function

A Air Hose Connects air to tool

B Filter Prevents dirt and condensation from damaging tool or work piece

C Regulator Adjusts air pressure to tool

D Lubricator (optional) For air tool lubrication

E Coupler and Plug Provides quick connection and release

F Leader Hose (optional) Increases coupler life

G Air Cleaner / Dryer (optional) Prevents water vapor from damaging work piece

H Air Adjusting Valve (optional) For fine tuning airflow at tool

Page 9For technical questions, please call 1-800-444-3353.Item 69269

SAFETYOPERATIONMAINTENANCE SETUP

Figure C: Stationary Air Supply Setup

N

L

L O

M

C

C

Non-lubricated

Tools

Lubricated

Tools

H

I

I

J

JKH

F

G

E

Slope

F

F

B B

A A

CD

Description Function

A Vibration Pads For noise and vibration reduction

B Anchor Bolts Secures air compressor in place

C Ball Valve Isolates sections of system for maintenance

D Isolation Hose For vibration reduction

EMain Air Line - 3/4″ minimum recommended Distributes air to branch lines

F Ball Valve To drain moisture from system

GBranch Air Line -1/2″ minimum recommended Brings air to point of use

H Air Hose Connects air to tool

I Filter Prevents dirt and condensation from damaging tool or work piece

J Regulator Adjusts air pressure to tool

K Lubricator (optional) For air tool lubrication

L Coupler and Plug Provides quick connection and release

M Leader Hose (optional) Increases coupler life

N Air Cleaner / Dryer (optional) Prevents water vapor from damaging work piece

O Air Adjusting Valve (optional) For fine tuning airflow at tool

Page 10 For technical questions, please call 1-800-444-3353. Item 69269

SAFETY OPERATION MAINTENANCESETUP

Operating Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this

manual including all text under subheadings therein before set up or use of this product.

Compressor Area Set Up

1. Designate a work area that is clean and well-lit.

The work area must not allow access by

children or pets to prevent injury.

2. Locate the Compressor on a flat level surface to

ensure proper pump lubrication and to prevent

damage to the unit. Keep at least 12″ of space

around the unit to allow air circulation.

3. Route the power cord from the compressor

to the grounded wall outlet, along a safe path

without creating a tripping hazard or exposing

the power cord to possible damage.

General Operation

1. Close the Drain Valve.

2. Close the in-line Shutoff Valve between

the compressor and the air hose.

3. Plug the Air Compressor Power Cord into

a grounded 120 V~ electrical outlet.

4. Turn the Power Switch ON.

5. Allow the Air Compressor to build

up pressure until it cycles off.

Note: At the beginning of the day’s first use of the

Air Compressor, check for air leaks by applying soapy

water to connections while the Air Compressor is

pumping and after pressure cut-out. Look for air bubbles.

If air bubbles are present at connections, tighten

connections. Do not use the Air Compressor

unless all connections are air tight, the extra air

leaking out will cause the compressor to operate

too often, increasing wear on the compressor.

Note: As long as the Power Switch is ON, the operation

of the Air Compressor is automatic, controlled by an

internal pressure switch. The Compressor will turn on

automatically when the air pressure drops to 85 PSI,

and will turn off automatically when the

air pressure reaches 100 PSI.

WARNING! TO PREVENT SERIOUS

INJURY AND DEATH FROM EXPLOSION:

Do not adjust the internal

pressure switch. Any change to the

automatic pressure levels may cause

excess pressure to accumulate,

causing a hazardous situation.

6. Adjust the Air Compressor’s Pressure Regulator

so that the air output is enough to properly

power the tool, but the output will not exceed

the tool’s maximum air pressure at any time.

Turn the knob clockwise to increase the pressure

and counter-clockwise to decrease pressure.

Adjust the pressure gradually, while checking

the air output gauge to set the pressure.

7. Make sure the air tool’s throttle or switch is in the

off position. Connect the air tool to the air hose.

8. Open the in-line Shutoff Valve.

9. Use the air tool as needed.

10. After the job is complete, turn the Power Switch OFF.

11. Unplug the Air Compressor.

12. Close the in-line Shutoff Valve.

13. Bleed air from the tool then disconnect the tool.

14. Turn the Drain Valve, at the bottom of the Tank,

two turns to release any built-up moisture and the

internal tank pressure. Close the valve after moisture

has drained out. Do not remove the Drain Valve.

15. Clean, then store the Air Compressor indoors.

Page 11For technical questions, please call 1-800-444-3353.Item 69269

SAFETYOPERATIONMAINTENANCE SETUP

Emergency Depressurization

If it is necessary to quickly depressurize the Compressor, turn the Power Switch OFF.

Then, pull on the ring on the Safety Valve to quickly release stored air pressure.

Automatic Shut off System

1. If the Compressor automatically shuts off

before reaching its normal cutoff pressure:

a. Shut off all tools.

b. Wait until the Compressor cools down

(about 10 minutes);

c. If the unit does not start up again on its own,

press the Reset Button to start the compressor;

d. Resume operation.

2. Possible causes of repeated automatic

shut off of the compressor are:

a. Using an extension cord that is too long or narrow;

b. An air leak or open hose causing the compressor

to cycle too often and build up heat.

3. Correct any issues before further use to

avoid damage to the compressor.

Page 12 For technical questions, please call 1-800-444-3353. Item 69269

SAFETY OPERATION MAINTENANCESETUP

Maintenance and Servicing

Procedures not specifically explained in this manual must

be performed only by a qualified technician.

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:

Turn the Power Switch “OFF” and unplug the Compressor from its electrical outlet

before performing any inspection, maintenance, or cleaning procedures.

TO PREVENT SERIOUS INJURY FROM COMPRESSOR FAILURE:

Do not use damaged equipment. If abnormal noise or vibration occurs,

have the problem corrected before further use.

Cleaning, Maintenance, and Lubrication

1. BEFORE EACH USE, inspect the general

condition of the Air Compressor.

Check for loose hardware, misalignment or binding

of moving parts, damaged belts, cracked or broken

parts, damaged electrical wiring, and any other

condition that may affect its safe operation.

2. AFTER USE, wipe external surfaces of

the compressor with a clean cloth.

3. WARNING! If the supply cord of this

compressor is damaged, it must be replaced

only by a qualified service technician.

Maintenance Schedule

Following are general guidelines for maintenance checks of the Air Compressor.

Note: The environment in which the compressor is used, and the frequency of use can affect how often

you will need to check the Air Compressor components and perform maintenance procedures.

Daily:

a. Make sure all nuts and bolts are tight.

b. Drain moisture from air tank.

c. Check for abnormal noise or vibration.

d. Check for air leaks.*

e. Wipe off any oil or dirt from the compressor.**

* To check for air leaks, apply soapy water to joints while

the Air Compressor is pressurized. Look for air bubbles.

** To clean the compressor surface, wipe with

a damp cloth, using a mild detergent or mild solvent.

Monthly:

Inspect Safety Valve.

Draining Moisture from the Tank

The Drain Valve is located under the Tank. It must be accessed daily to release all trapped air and

moisture from the Tank. This will eliminate condensation which can cause tank corrosion.

CAUTION! Do not open the Drain Valve so that more than four threads are showing.

1. Turn the Power switch of the compressor off.

2. Place a collection pan under the Drain Valve.

3. Unthread the Drain Valve two or three turns ONLY.

4. When all the pressure and moisture is released,

close the Drain Valve.

Page 13For technical questions, please call 1-800-444-3353.Item 69269

SAFETYOPERATIONMAINTENANCE SETUP

Troubleshooting

Problem Possible Causes Likely Solutions

Compressor does

not start or restart

1. Tank(s) already pressurized.

2. Power cord not plugged in properly.

3. Incorrect power supply.

4. No power at outlet.

5. Thermal overload switch tripped.

6. Building power supply circuit tripped or

blown fuse.

7. Cord wire size is too small or cord is too

long to properly power compressor.

8. Compressor needs service.

1. No problem. Compressor will start when needed.

2. Check that cord is plugged in securely.

3. Check that circuit matches compressor requirements.

4. Reset circuit breaker, or have outlet

serviced by a qualified technician.

5. Turn off Compressor and wait for it to cool down.

Press reset button. Resume operation.

6. Reset circuit or replace fuse. Check for low voltage

conditions. It may be necessary to disconnect

other electrical appliances from the circuit or

move the compressor to its own circuit.

7. Use larger diameter or shorter extension cord or

eliminate extension cord. See Recommended Wire

Gauge for Extension Cords in Safety section.

8. Have unit inspected by a qualified technician.

Compressor builds

pressure too slowly

1. Incorrect power supply.

2. Working environment too cold.

3. Safety valve leaking.

4. Loose fittings.

1. Check that circuit matches compressor requirements.

2. Move compressor to a warmer location.

Check that recommended oil is in crankcase.

3. Listen for air leaking from valve.

If leaking, replace with identical valve with same rating.

DO NOT SEAL OR TAMPER WITH SAFETY VALVE.

4. Reduce air pressure, then check all fittings with

a soap solution for air leaks and tighten as needed.

Do not overtighten.

Compressor not

building enough

air pressure

1. Air filters need cleaning/replacing.

2. Check Valve needs service.

3. Compressor not large enough for job.

4. Loose fittings.

5. Hose or hose connections too narrow.

6. High altitude reducing air output.

1. Check inlet and outlet filters.

Clean and/or replace as needed.

2. Have technician clean or replace, as needed.

3. Check if accessory CFM is met by Compressor.

If Compressor cannot supply enough air flow (CFM),

you need a larger Compressor.

4. Reduce air pressure, then check all fittings with

a soap solution for air leaks and tighten as needed.

Do not overtighten.

5. Replace with wider hose and/or hose connections.

6. Higher altitudes require compressors with greater output.

Overheating 1. Unusually dusty environment.

2. Extension cord used.

3. Unit not on level surface.

1. Clean and/or replace filters more often or

move unit to cleaner environment.

2. Eliminate extension cord.

3. Reposition unit on a level surface.

Compressor

starts and stops

excessively

1. Loose fittings.

2. Compressor not large enough for job.

1. Reduce air pressure, then check all fittings with a soap

solution for air leaks and tighten as needed.

Do not overtighten.

2. Check if accessory CFM is met by Compressor.

If Compressor doesn’t reach accessory

CFM, you need a larger Compressor.

Excessive noise 1. Loose fittings.

2. Unit not on level surface.

1. Reduce air pressure, then check all fittings with a soap

solution for air leaks and tighten as needed.

Do not overtighten.

2. Reposition unit on a level surface.

Moisture in

discharge air

Too much moisture in air. Install inline air filter/dryer, and/or relocate

to less humid environment.

Safety Valve “pops” Safety valve needs service. Pull on test ring of safety valve. If it still pops, replace.

Air leaks from

pump or fittings

Loose fittings. Reduce air pressure, then check all fittings with a soap

solution for air leaks and tighten as needed.

Do not overtighten.

Follow all safety precautions whenever diagnosing or servicing the compressor.

Disconnect power supply before service.

Page 14 For technical questions, please call 1-800-444-3353. Item 69269

SAFETY OPERATION MAINTENANCESETUP

Parts List and Diagram

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN

THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY

REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS

TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE

MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD

BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES

ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT

PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Parts List

Record Product’s Serial Number Here:

Note: If product has no serial number, record month and year of purchase instead.

Note: Some parts are listed and shown for illustration purposes only,

and are not available individually as replacement parts.

Part Description Qty

1 Motor 1

2 Crank 1

3 Screw 1

4 Bearing (608-2RS) 1

5 Connecting Rod 1

6 Silica Gel Ring (21.2 x 2.5) 1

7 Piston Ring 1

8 Paper Pad 1

9 Hoop 1

10 Cylinder 1

11 Cylinder Washer 1

12 Silica Gel Ring (31 x 2) 1

13 Cylinder Head 1

14 Connector 2

15 Silica Gel Ring (31.5 x 1.8) 1

16 Screw (M4 x 40) 4

17 Flat Washer 5

18 Spring Washer 5

19 Fan 1

20 Screw (M4 x 10) 1

23 Tube 1

24 Pressure Regulator 1

25 Safety Valve 1

26 Tank Pressure Gauge 1

27 Coupler 1

28 Four Way Block 1

29 Muffler Board 1

30 Screw (M3 x 6) 4

31 Copper Connector Rod 2

32 Copper Hoop 2

33 Screw (M6 x 25) 4

34 Damping Pad 1

Part Description Qty

35 Power Cord 1

36 Motor Cover 1

37 Circuit Board 1

38 Screw (M4 x 8) 2

39 Washer 1

40 Wire Clip 1

41 Screw (M4 x 15) 2

42 Nut 4

43 Fuse (3 Amp) 1

44 Fuse Box 1

45 ON/OFF Power Switch 1

46 Screw (M5 x 16) 2

47 Handle 1

48 Handle Soft Grip 1

49 Wire 1

50 Flat Washer 1

51 Zip Tie 1

52 Rubber Sheath 1

53 Air Tank 1

54 Drain Valve 1

55 Rubber Foot 4

56 Pressure switch 1

57 Ball 1

58 Spring 1

59 Screw (M6 x 15) 4

60 Flat Washer 6

61 Copper Tube 1

62 Screw (M6 x 20) 4

70 Regulated Pressure Gauge 1

71 Air Flow Valve (not shown) 1

72 1/4″ Connector (not shown) 1

Page 15For technical questions, please call 1-800-444-3353.Item 69269

SAFETYOPERATIONMAINTENANCE SETUP

Assembly Diagram

36

52

62

14

31

61

57

58

48

26

24

27

25

28

46

47

53

54

55

59

60

42

37

9

51

23

35

3

5

6

32

4

8

21

10

11

13

17

18

16

43

45

44

32

33

56

41

70

20 17 19

50

31

38

15

49

14

30

29

39

34

20

12

7

40

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,

and warrants to the original purchaser that this product is free from defects in materials and workmanship for the

period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,

to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper

installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries

to persons or property, or for incidental, contingent, special or consequential damages arising from the use of

our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the

above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER

WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with transportation charges

prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.

If our inspection verifies the defect, we will either repair or replace the product at our election or we may

elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will

return repaired products at our expense, but if we determine there is no defect, or that the defect resulted

from causes not within the scope of our warranty, then you must bear the cost of returning the product.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353