Harbor Freight 69730 Owner S Manual

: Harbor-Freight Harbor-Freight-69730-Owner-S-Manual harbor-freight-69730-owner-s-manual harbor-freight pdf

Open the PDF directly: View PDF .
Page Count: 24

Page 2 For technical questions, please call 1-800-520-0882. ITEM 69727

69730

Table of Contents

Specifications ............................................. 2

Safety ......................................................... 3

Setup .......................................................... 6

Operation .................................................... 8

Maintenance .............................................. 12

Troubleshooting ......................................... 16

Warranties ................................................. 18

Parts Lists and Diagrams .......................... 20

Specifications

Displacement 212cc

Engine Type

Horizontal Single Cylinder

4 stroke OHV

69727: Meets EPA phase III and

CARB emissions standards

69730: Meets EPA phase III

emissions standards

Cooling System Forced air cooled

Fuel Type 87+ octane unleaded gasoline

Capacity 0.9 Gallon (3.6 Liter)

Engine Oil Type SAE 10W-30 above 32° F

5W-30 at 32° F or below

Capacity 0.5 Quart

Run Time @ 50% Load

with full tank 3 hr.

Sound Level at 22 feet 104 dB

Bore x Stroke 70 mm x 55 mm

Compression Ratio 8.5:1

Rotation viewed from PTO

(power takeoff - the output shaft) Counterclockwise

Shaft

Shaft 3/4″ x 2.43″

Keyway 3/16″ (4.76 mm)

End Tapped 5/16″ - 24 UNF

Spark Plug Type NGK® BP-6ES

NHSP® / Torch® F6TC

Gap 0.7 - 0.8 mm

Valve Clearance Intake 0.10 - 0.15 mm

Exhaust 0.15 - 0.20 mm

Speed Idle 1,800 ± 50 RPM

SAFETY OPERATION MAINTENANCESETUP

Page 3For technical questions, please call 1-800-520-0882.ITEM 69727

69730

WARNING SYMBOLS AND DEFINITIONS

This is the safety alert symbol. It is used to alert you to potential personal injury hazards.

Obey all safety messages that follow this symbol to avoid possible injury or death.

Indicates a hazardous situation which, if not avoided,

will result in death or serious injury.

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

Addresses practices not related to personal injury.

Symbol Definitions

Symbol Property or Statement

RPM Revolutions Per Minute

HP Horsepower

WARNING marking concerning

Risk of Eye Injury. Wear ANSI-approved

safety goggles with side shields.

Read the manual before set-up and/or use.

WARNING marking concerning

Risk of Hearing Loss.

Wear hearing protection.

Symbol Property or Statement

WARNING marking concerning

Risk of Respiratory Injury.

Operate engine OUTSIDE and far away

from windows, doors, and vents.

WARNING marking concerning

Risk of Fire while handling fuel.

Do not smoke while handling fuel.

WARNING marking concerning

Risk of Fire.

Do not refuel while operating.

Keep flammable objects away from engine.

Safety Warnings

WARNING! Read all instructions.

Failure to follow all instructions listed below may result in fire, serious injury and/or DEATH.

The warnings and precautions discussed in this manual cannot cover all possible conditions and

situations that may occur. It must be understood by the operator that common sense and caution

are factors which cannot be built into this product, but must be supplied by the operator.

SAVE THESE INSTRUCTIONS

SAFETYOPERATIONMAINTENANCE SETUP

Page 4 For technical questions, please call 1-800-520-0882. ITEM 69727

69730

Set up Precautions

1. Gasoline fuel and fumes are flammable, and

potentially explosive. Use proper fuel storage

and handling procedures. Do not store fuel

or other flammable materials nearby.

2. Have multiple ABC class fire extinguishers nearby.

3. Operation of this equipment may create sparks

that can start fires around dry vegetation. A spark

arrestor may be required. The operator should

contact local fire agencies for laws or regulations

relating to fire prevention requirements.

4. Set up and use only on a flat, level,

well-ventilated surface.

5. Wear ANSI-approved safety goggles, heavy-duty

work gloves, and dust mask/respirator during set up.

6. Use only lubricants and fuel recommended

in the Specifications chart of this manual.

Operating Precautions

1. CARBON MONOXIDE HAZARD

Using an engine indoors CAN KILL

YOU IN MINUTES.

Engine exhaust contains carbon

monoxide. This is a poison you cannot

see or smell.

NEVER use inside a home or garage,

EVEN IF doors and windows are open.

Only use OUTSIDE and far away from windows,

doors, and vents.

2. Keep children away from the equipment,

especially while it is operating.

3. Keep all spectators at least six feet

from the Engine during operation.

4. Fire Hazard! Do not fill gas tank while engine is

running. Do not operate if gasoline has been spilled.

Clean spilled gasoline before starting engine.

Do not operate near pilot light or open flame.

5. Do not touch engine during use.

Let engine cool down after use.

6. Never store fuel or other flammable

materials near the engine.

7. Only use a suitable means of transport and

lifting devices with sufficient weight bearing

capacity when transporting the Engine.

8. Secure the Engine on transport vehicles to

prevent the tool from rolling, slipping, and tilting.

9. Industrial applications must follow

OSHA requirements.

10. Do not leave the equipment unattended when it is

running. Turn off the equipment (and remove safety

keys, if available) before leaving the work area.

11. Engine can produce high noise levels.

Prolonged exposure to noise levels

above 85 dBA is hazardous to hearing.

Always wear ear protection when operating or

working around the gas engine while it is operating.

12. Wear ANSI-approved safety glasses, hearing

protection, and NIOSH-approved dust mask/

respirator under a full face shield along

with steel-toed work boots during use.

13. People with pacemakers should consult their

physician(s) before use. Electromagnetic fields in

close proximity to a heart pacemaker could cause

pacemaker interference or pacemaker failure.

Caution is necessary when near the

engine’s magneto or recoil starter.

14. Use only accessories that are recommended

by Harbor Freight Tools for your model.

Accessories that may be suitable for one

piece of equipment may become hazardous

when used on another piece of equipment.

15. Do not operate in explosive atmospheres,

such as in the presence of flammable

liquids, gases, or dust. Gasoline-powered

engines may ignite the dust or fumes.

16. Stay alert, watch what you are doing and

use common sense when operating this

piece of equipment. Do not use this piece of

equipment while tired or under the influence

of drugs, alcohol or medication.

17. Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the equipment in unexpected situations.

18. Use this equipment with both hands

only. Using equipment with only one hand

can easily result in loss of control.

19. Dress properly. Do not wear loose clothing or

jewelry. Keep hair, clothing and gloves away

from moving parts. Loose clothes, jewelry or

long hair can be caught in moving parts.

SAFETY OPERATION MAINTENANCESETUP

Page 5For technical questions, please call 1-800-520-0882.ITEM 69727

69730

20. Parts, especially exhaust system components,

get very hot during use. Stay clear of hot parts.

21. Do not cover the engine or

equipment during operation.

22. Keep the equipment, engine, and

surrounding area clean at all times.

23. Use the equipment, accessories, etc., in accordance

with these instructions and in the manner intended for

the particular type of equipment, taking into account

the working conditions and the work to be performed.

Use of the equipment for operations different from

those intended could result in a hazardous situation.

24. Do not operate the equipment with known

leaks in the engine’s fuel system.

25. This product contains or, when used, produces a

chemical known to the State of California to cause

cancer and birth defects or other reproductive harm.

(California Health & Safety Code § 25249.5, et seq.)

26. When spills of fuel or oil occur, they must be

cleaned up immediately. Dispose of fluids and

cleaning materials as per any local, state, or

federal codes and regulations. Store oil rags in

a bottom-ventilated, covered, metal container.

27. Keep hands and feet away from moving parts. Do

not reach over or across equipment while operating.

28. Before use, check for misalignment or binding of

moving parts, breakage of parts, and any other

condition that may affect the equipment’s operation.

If damaged, have the equipment serviced

before using. Many accidents are caused

by poorly maintained equipment.

29. Use the correct equipment for the application.

Do not modify the equipment and do not use the

equipment for a purpose for which it is not intended.

Service Precautions

1. Before service, maintenance, or cleaning:

a. Turn the engine switch to its “OFF” position.

b. Allow the engine to completely cool.

c. Then, remove the spark plug

cap from the spark plug.

2. Keep all safety guards in place and in

proper working order. Safety guards include

muffler, air cleaner, mechanical guards,

and heat shields, among other guards.

3. Do not alter or adjust any part of the

equipment or its engine that is sealed by the

manufacturer or distributor. Only a qualified

service technician may adjust parts that may

increase or decrease governed engine speed.

4. Wear ANSI-approved safety goggles, heavy-duty

work gloves, and dust mask/respirator during service.

5. Maintain labels and nameplates on the equipment.

These carry important information.

If unreadable or missing, contact

Harbor Freight Tools for a replacement.

6. Have the equipment serviced by a qualified repair

person using only identical replacement parts.

This will ensure that the safety of the equipment

is maintained. Do not attempt any service or

maintenance procedures not explained in this

manual or any procedures that you are uncertain

about your ability to perform safely or correctly.

7. Store equipment out of the reach of children.

8. Follow scheduled engine and

equipment maintenance.

Refueling:

1. Do not smoke, or allow sparks, flames,

or other sources of ignition around the

equipment, especially when refuelling.

2. Do not refill the fuel tank while the

engine is running or hot.

3. TO PREVENT FUEL LEAKAGE AND

FIRE HAZARD, do not fill fuel above

the bottom of fuel strainer.

Max Fuel

DO NOT OVERFILL!

4. Do not fill fuel tank to the top. Leave a little

room for the fuel to expand as needed.

5. Refuel in a well-ventilated area only.

6. Wipe up any spilled fuel and allow excess

to evaporate before starting engine.

To prevent FIRE, do not start the engine

while the smell of fuel hangs in the air.

SAVE THESE INSTRUCTIONS.

Operating Precautions (cont.)

SAFETYOPERATIONMAINTENANCE SETUP

Page 6 For technical questions, please call 1-800-520-0882. ITEM 69727

69730

Set Up

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual

including all text under subheadings therein before set up or use of this product.

TO PREVENT SERIOUS INJURY:

Operate only with proper spark arrestor installed.

Operation of this equipment may create sparks that

can start fires around dry vegetation.

A spark arrestor may be required.

The operator should contact local fire

agencies for laws or regulations relating

to fire prevention requirements.

At high altitudes, the engine’s carburetor, governor

(if so equipped), and any other parts that control

the fuel-air ratio will need to be adjusted by a

qualified mechanic to allow efficient high-altitude

use and to prevent damage to the engine and

any other devices used with this product.

For item 69727: The emission control system for this

Engine is warranted for standards set by the U.S.

Environmental Protection Agency and by the California Air

Resources Board (also known as CARB). For warranty

information, refer to the last pages of this manual.

For item 69730: The emission control system for

this Engine is warranted for standards set by the

U.S. Environmental Protection Agency. For warranty

information, refer to the last pages of this manual.

WARNING! DO NOT INSTALL THIS

ENGINE ON A VEHICLE.

SAFETY OPERATION MAINTENANCESETUP

Page 7For technical questions, please call 1-800-520-0882.ITEM 69727

69730

Engine

Switch

Engine Controls

Starter

Handle

Oil Drain Plug

Air Filter

Fuel Valve

Choke

Fuel Cap

Throttle

Muffler

Dipstick

SAFETYOPERATIONMAINTENANCE SETUP

Page 8 For technical questions, please call 1-800-520-0882. ITEM 69727

69730

Operation

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual

including all text under subheadings therein before set up or use of this product.

Pre-Start Checks

Inspect engine and equipment looking for damaged, loose, and missing parts before set up

and starting. If any problems are found, do not use equipment until fixed properly.

Checking and Filling Engine Oil

NOTICE: Your Warranty is VOID if the engine’s

crankcase is not properly filled with oil before

each use. Before each use, check the oil level.

Do not run the engine with low or no engine oil.

Running the engine with no or low engine oil

WILL permanently damage the engine.

1. Make sure the engine is stopped and is level.

2. Close the Fuel Valve.

3. Clean the top of the Dipstick and the area around it.

Remove the Dipstick by threading it counterclockwise,

and wipe it off with a clean lint free rag.

4.

Full level

Full level

Reinsert the Dipstick without threading it in and

remove it to check the oil level. The oil level

should be up to the full level as shown above.

5. If the oil level is at or below the low mark add the

appropriate type of oil until the oil level is at the

proper level. SAE 10W-30 oil is recommended

for general use. (The SAE Viscosity Grade chart

on page 13 in the Service section shows other

viscosities to use in different average temperatures.)

6. Thread the dipstick back in clockwise.

NOTICE: Do not run the engine with too little oil.

The engine will be permanently damaged.

SAFETY OPERATION MAINTENANCESETUP

Page 9For technical questions, please call 1-800-520-0882.ITEM 69727

69730

Checking and Filling Fuel

WARNING! TO PREVENT SERIOUS

INJURY FROM FIRE:

Fill the fuel tank in a well-ventilated area

away from ignition sources. If the engine is

hot from use, shut the engine off and wait

for it to cool before adding fuel.

Do not smoke.

1. Clean the Fuel Cap and the area around it.

2. Unscrew and remove the Fuel Cap.

3. If needed, fill the Fuel Tank to about 1 inch

under the fill neck of the Fuel Tank with

87 octane or higher unleaded gasoline.

Note: Do not use gasoline containing more than

10% ethanol (E10). Do not use E85 ethanol.

Note: Do not use gasoline that has been stored in a

metal fuel container or a dirty fuel container. It can

cause particles to enter the carburetor, affecting

engine performance and/or causing damage.

4. Then replace the Fuel Cap.

5. Wipe up any spilled fuel and allow excess

to evaporate before starting engine.

To prevent FIRE, do not start the engine

while the smell of fuel hangs in the air.

Starting the Engine

Before Starting the Engine

Before starting the engine:

a. Follow the Set Up Instructions in the equipment manual to prepare the equipment.

b. Inspect the equipment and engine.

c. Fill the engine with the proper amount and type of both fuel and oil.

d. Read the Equipment Operation section in the equipment manual.

SAFETYOPERATIONMAINTENANCE SETUP

Page 10 For technical questions, please call 1-800-520-0882. ITEM 69727

69730

Manual Start

1. To start a cold engine, move the Choke to the

CHOKE position.

To restart a warm engine, leave the Choke in the

RUN position.

2. Open the Fuel Valve.

3. Slide the Throttle or Speed Control Lever to 1/3

away from the SLOW position (the “turtle”).

Note: Some tools have a Speed Control Lever located

elsewhere on the tool which functions the same as the

Throttle. Use the Speed Control Lever in place of the Throttle

when the tool is so equipped.

4. Turn the Engine Switch on.

5. Grip the Starter Handle of the Engine loosely and pull

it slowly several times to allow the gasoline to flow into

the Engine’s carburetor. Then pull the Starter Handle

gently until resistance is felt. Allow Cable to retract fully

and then pull it quickly. Repeat until the engine starts.

Note: Do not let the Starter Handle snap back against the engine.

Hold it as it recoils so it doesn't hit the engine.

CHOKE RUN

1

2

3

ON

OFF

OI

ON

4

5

SAFETY OPERATION MAINTENANCESETUP

Page 11For technical questions, please call 1-800-520-0882.ITEM 69727

69730

6. Allow the Engine to run for several seconds.

Then, if the Choke lever is in the CHOKE position,

move the Choke Lever very slowly to its RUN position.

Note: Moving the Choke Lever too fast could stall the engine.

IMPORTANT: Allow the engine to run at no load for five minutes with no

load after each start-up so that the engine can stabilize.

7. Adjust the Throttle as needed.

8. Break-in Period:

a. Breaking-in the engine will help to ensure proper equipment and engine operation.

b. The operational break-in period will last about 3 hours of use. During this period:

• Do not apply a heavy load to the equipment.

• Do not operate the engine at its maximum speed.

c. The maintenance break-in period will last about 20 hours of use. After this period:

• Change the engine oil.

Under normal operating conditions subsequent maintenance follows the schedule

explained in the MAINTENANCE AND SERVICING section.

Stopping the Engine

1. To stop the engine in an emergency,

turn the Engine Switch off.

2. Under normal conditions, use the following procedure:

a. Slide the Throttle or Speed Control

Lever to SLOW (the “turtle”).

b. Turn the Engine Switch off.

c. Close the Fuel Valve.

CHOKE RUN

6

OI

OFF

SAFETYOPERATIONMAINTENANCE SETUP

Page 12 For technical questions, please call 1-800-520-0882. ITEM 69727

69730

Maintenance

WARNING

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL STARTING:

Turn the Power Switch of the equipment to its “OFF” position, wait for the engine to cool, and disconnect

the spark plug cap before performing any inspection, maintenance, or cleaning procedures.

TO PREVENT SERIOUS INJURY FROM EQUIPMENT FAILURE:

Do not use damaged equipment. If abnormal noise, vibration, or excess

smoking occurs, have the problem corrected before further use.

Follow all service instructions in this manual. The engine may fail critically if not serviced properly.

Many maintenance procedures, including any not detailed in this manual, will need to be

performed by a qualified technician for safety. If you have any doubts about your ability to safely

service the equipment or engine, have a qualified technician service the equipment instead.

Cleaning, Maintenance, and Lubrication Schedule

Note: This maintenance schedule is intended solely as a general guide. If performance decreases or if

equipment operates unusually, check systems immediately. The maintenance needs of each piece of equipment

will differ depending on factors such as duty cycle, temperature, air quality, fuel quality, and other factors.

Note: The following procedures are in addition to the regular checks and maintenance

explained as part of the regular operation of the engine and equipment.

Procedure Before

Each Use

Monthly or

every 20

hr. of use

Every 3 mo. or

50 hr. of use

Every 6 mo. or

100 hr. of use

Yearly or

every 300

hr. of use

Every

2 Years

Brush off outside of engine

Check engine oil level

Check air cleaner

Check deposit cup

Change engine oil

Clean/replace air cleaner *

Check and clean spark plug

1. Check/adjust idle speed

2. Check/adjust valve clearance

3. Clean fuel tank, strainer

and carburetor

4. Clean carbon build-up from

combustion chamber

** **

Replace fuel line if necessary **

*Service more frequently when used in dusty areas.

**These items should be serviced by a qualified technician.

SAFETY OPERATION MAINTENANCESETUP

Page 13For technical questions, please call 1-800-520-0882.ITEM 69727

69730

Checking and Filling Fuel

WARNING! TO PREVENT SERIOUS

INJURY FROM FIRE:

Fill the fuel tank in a well-ventilated area

away from ignition sources. If the engine is

hot from use, shut the engine off and wait

for it to cool before adding fuel.

Do not smoke.

1. Clean the Fuel Cap and the area around it.

2. Unscrew and remove the Fuel Cap.

3. If needed, fill the Fuel Tank to about 1 inch under

the fill neck of the Fuel Tank with 87 octane or

higher unleaded gasoline. Fill to the bottom

of the fuel strainer ONLY, see below.

Max Fuel

DO NOT OVERFILL!

WARNING! TO PREVENT FUEL

LEAKAGE AND FIRE HAZARD, do not fill

fuel above the bottom of fuel strainer.

Note: Do not use gasoline containing more than

10% ethanol (E10). Do not use E85 ethanol.

Note: Do not use gasoline that has been stored in a

metal fuel container or a dirty fuel container. It can

cause particles to enter the carburetor, affecting

engine performance and/or causing damage.

4. Then replace the Fuel Cap.

5. Wipe up any spilled fuel and allow excess

to evaporate before starting engine.

To prevent FIRE, do not start the engine

while the smell of fuel hangs in the air.

Engine Oil Change

CAUTION! Oil is very hot during operation and can

cause burns. Wait for engine to cool before changing oil.

1. Make sure the engine is stopped and is level.

2. Close the Fuel Valve.

3. Place a drain pan (not included) underneath

the crankcase’s drain plug.

4. Remove the drain plug and, if possible,

tilt the crankcase slightly to help drain

the oil out. Recycle used oil.

5. Replace the drain plug and tighten it.

6. Clean the top of the Dipstick and the area around it.

Remove the Dipstick by threading it counterclockwise,

and wipe it off with a clean lint free rag.

7.

Full level

Full level

Add the appropriate type of oil until the oil level is at

the full level. SAE 10W-30 oil is recommended for

general use.

The SAE Viscosity Grade chart shows other

viscosities to use in different average temperatures.

10W-30

30

5W-30

-20 0 20 40 60 80 100°F

SAE Viscosity Grades

Average outdoor temperature

8. Thread the dipstick back in clockwise.

CAUTION! Do not run the engine with too little oil.

The engine will be permanently damaged.

SAFETYOPERATIONMAINTENANCE SETUP

Page 14 For technical questions, please call 1-800-520-0882. ITEM 69727

69730

Air Filter Element Maintenance

1. Remove the air filter cover and the

air filter elements and check for dirt.

Clean or replace as described below.

2. Cleaning:

• For “paper” filter elements:

To prevent injury from dust and debris,

wear ANSI-approved safety goggles,

NIOSH-approved dust mask/respirator, and

heavy-duty work gloves. In a well-ventilated

area away from bystanders, use pressurized

air to blow dust out of the air filter.

If this does not get the filter clean, replace it.

• For foam filter elements:

Wash the element in warm water and

mild detergent several times. Rinse.

Squeeze out excess water and allow it to dry

completely. Soak the filter in lightweight oil

briefly, then squeeze out the excess oil.

3. Install the new filter or the cleaned filter.

Secure the Air Cleaner Cover before use.

Spark Plug Maintenance

1.

Spark

Plug

Cap

Disconnect spark plug cap from end of plug.

Clean out debris from around spark plug.

2. Using a spark plug wrench, remove the spark plug.

3. Inspect the spark plug:

If the electrode is oily, clean it using a clean, dry rag.

If the electrode has deposits on it, polish it using

emery paper. If the white insulator is cracked or

chipped, the spark plug needs to be replaced.

Recommended Spark Plugs

NGK®BP-6ES

NHSP® / TORCH®F6TC

NOTICE: Using an incorrect spark

plug may damage the engine.

4. When installing a new spark plug, adjust the

plug’s gap to the specification on the Technical

Specifications chart. Do not pry against the

electrode, the spark plug can be damaged.

5. Install the new spark plug or the cleaned spark plug

into the engine. Gasket-style: Finger-tighten until the

gasket contacts the cylinder head, then tighten about

1/2-2/3 turn more.

Non-gasket-style: Finger-tighten until the plug

contacts the head, then tighten about 1/16 turn more.

NOTICE: Tighten the spark plug properly.

If loose, the spark plug will cause the engine to overheat.

If overtightened, the threads in the

engine block will be damaged.

6. Apply dielectric spark plug boot protector

(not included) to the end of the spark

plug and reattach the wire securely.

SAFETY OPERATION MAINTENANCESETUP

Page 15For technical questions, please call 1-800-520-0882.ITEM 69727

69730

Storage

When the equipment is to remain idle for longer than

20 days, prepare the engine for storage as follows:

1. CLEANING:

Wait for engine to cool, then clean engine with

dry cloth. NOTICE: Do not clean using water.

The water will gradually enter the engine

and cause rust damage. Apply a thin coat

of rust preventive oil to all metal parts.

2. FUEL:

WARNING! TO PREVENT SERIOUS

INJURY FROM FIRE:

Drain the fuel tank in a well-ventilated area

away from ignition sources. If the engine is

hot from use, shut the engine off and wait

for it to cool before draining fuel.

Do not smoke.

a. Place a funnel leading to a proper gasoline

container below the carburetor.

b.

Drain Plug

Sediment Cup

(some engines)

Remove the drain bolt from the bottom of the

carburetor bowl and allow the fuel to drain.

c. Remove the small sediment cup next to the bowl

and allow the fuel to drain from there as well.

d. Open the fuel valve. After all fuel has

drained, reinstall the drain bolt and sediment

cup (if equipped). Tighten securely.

3. LUBRICATION:

a. Change engine oil.

b. Clean out area around spark plug. Remove

spark plug and pour one tablespoon of engine

oil into cylinder through spark plug hole.

c. Replace spark plug, but leave spark

plug cap disconnected.

d. Pull Starter Handle to distribute oil in cylinder.

Stop after one or two revolutions when you

feel the piston start the compression stroke

(when you start to feel resistance).

4. BATTERY:

Disconnect battery cables (if equipped).

Recharge batteries monthly while in storage.

5. STORAGE AREA:

Cover and store in a dry, level, well-ventilated

area out of reach of children. Storage area

should also be away from ignition sources, such

as water heaters, clothes dryers, and furnaces.

6. AFTER STORAGE:

Before starting the engine after storage, keep in

mind that untreated gasoline will deteriorate quickly.

Drain the fuel tank and change to fresh fuel if

untreated gasoline has been sitting for a month,

if treated gasoline has been sitting beyond

the fuel stabilizer’s recommended time

period, or if the engine does not start.

SAFETYOPERATIONMAINTENANCE SETUP

Page 16 For technical questions, please call 1-800-520-0882. ITEM 69727

69730

Troubleshooting

Problem Possible Causes Probable Solutions

Engine will not start FUEL RELATED:

1. No fuel in tank or fuel valve closed.

2. Choke not in CHOKE position, cold engine.

3. Gasoline with more than 10% ethanol

used. (E15, E20, E85, etc.)

4. Low quality or deteriorated, old gasoline.

5. Carburetor not primed.

6. Dirty fuel passageways.

7. Carburetor needle stuck.

Fuel can be smelled in the air.

8. Too much fuel in chamber. This can be

caused by the carburetor needle sticking.

9. Clogged Fuel Filter.

FUEL RELATED:

1. Fill fuel tank and open fuel valve.

2. Move Choke to CHOKE position.

3. Clean out ethanol rich gasoline from fuel

system. Replace components damaged

by ethanol. Use fresh 87+ octane

unleaded gasoline only.

Do not use gasoline with more than

10% ethanol (E15, E20, E85, etc.).

4. Use fresh 87+ octane unleaded gasoline.

Do not use gasoline with more than

10% ethanol (E15, E20, E85, etc.).

5. Pull on Starter Handle to prime.

6. Clean out passageways using

fuel additive. Heavy deposits

may require further cleaning.

7. Gently tap side of carburetor float

chamber with screwdriver handle.

8. Turn Choke to RUN position.

Remove spark plug and pull the start

handle several times to air out the

chamber. Reinstall spark plug and

set Choke to CHOKE position.

9. Replace Fuel Filter.

IGNITION (SPARK) RELATED:

1. Spark plug cap not connected securely.

2. Spark plug electrode wet or dirty.

3. Incorrect spark plug gap.

4. Spark plug cap broken.

5. Circuit breaker tripped

(electric start models only).

6. Incorrect spark timing or

faulty ignition system.

IGNITION (SPARK) RELATED:

1. Connect spark plug cap properly.

2. Clean spark plug.

3. Correct spark plug gap.

4. Replace spark plug cap.

5. Reset circuit breaker. Check wiring and

starter motor if breaker continues to trip.

6. Have qualified technician diagnose/

repair ignition system.

COMPRESSION RELATED:

1. Cylinder not lubricated. Problem after long

storage periods.

2. Loose or broken spark plug. (Hissing

noise will occur when trying to start.)

3. Loose cylinder head or damaged

head gasket. (Hissing noise will

occur when trying to start.)

4. Engine valves or tappets

mis-adjusted or stuck.

COMPRESSION RELATED:

1. Pour tablespoon of oil into spark

plug hole. Crank engine a few

times and try to start again.

2. Tighten spark plug. If that does not work,

replace spark plug. If problem persists,

may have head gasket problem, see #3.

3. Tighten head. If that does not remedy

problem, replace head gasket.

4. Have qualified technician diagnose/

repair ignition system.

Follow all safety precautions whenever diagnosing or servicing the equipment or engine.

SAFETY OPERATION MAINTENANCESETUP

Page 17For technical questions, please call 1-800-520-0882.ITEM 69727

69730

Problem Possible Causes Probable Solutions

Engine misfires 1. Spark plug cap loose.

2. Incorrect spark plug gap or

damaged spark plug.

3. Defective spark plug cap.

4. Old or low quality gasoline.

5. Incorrect compression.

1. Check wire connections.

2. Re-gap or replace spark plug.

3. Replace spark plug cap.

4. Use only fresh 87+ octane

unleaded gasoline.

Do not use gasoline with more than

10% ethanol (E15, E20, E85, etc.).

5. Diagnose and repair compression.

(Use Engine will not start:

COMPRESSION RELATED section.)

Engine stops

suddenly

1. Low oil shutdown.

2. Fuel tank empty or full of impure or low

quality gasoline.

3. Defective fuel tank cap creating

vacuum, preventing proper fuel flow.

4. Faulty magneto.

5. Disconnected or improperly

connected spark plug cap.

1. Fill engine oil to proper level. Check

engine oil before EVERY use.

2. Fill fuel tank with fresh 87+ octane

unleaded gasoline.

Do not use gasoline with more than

10% ethanol (E15, E20, E85, etc.).

3. Test/replace fuel tank cap.

4. Have qualified technician service magneto.

5. Secure spark plug cap.

Engine stops when

under heavy load

1. Dirty air filter

2. Engine running cold.

1. Clean or replace element.

2. Allow engine to warm up prior

to operating equipment.

Engine knocks 1. Old or low quality gasoline.

2. Engine overloaded.

3. Incorrect spark timing, deposit

buildup, worn engine, or other

mechanical problems.

1. Fill fuel tank with fresh 87+ octane

unleaded gasoline.

Do not use gasoline with more than

10% ethanol (E15, E20, E85, etc.).

2. Do not exceed equipment’s load rating.

3. Have qualified technician

diagnose and service engine.

Engine backfires 1. Impure or low quality gasoline.

2. Engine too cold.

3. Intake valve stuck or overheated engine.

4. Incorrect timing.

1. Fill fuel tank with fresh 87+ octane

unleaded gasoline.

Do not use gasoline with more than

10% ethanol (E15, E20, E85, etc.).

2. Use cold weather fuel and oil

additives to prevent backfiring.

3. Have qualified technician

diagnose and service engine.

4. Check engine timing.

Follow all safety precautions whenever diagnosing or servicing the equipment or engine.

SAFETYOPERATIONMAINTENANCE SETUP

Page 18 For technical questions, please call 1-800-520-0882. ITEM 69727

69730

Warranties

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,

and warrants to the original purchaser that this product is free from defects in materials and workmanship for the

period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,

to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper

installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries

to persons or property, or for incidental, contingent, special or consequential damages arising from the use of

our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the

above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER

WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with transportation charges

prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.

If our inspection verifies the defect, we will either repair or replace the product at our election or we may

elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will

return repaired products at our expense, but if we determine there is no defect, or that the defect resulted

from causes not within the scope of our warranty, then you must bear the cost of returning the product.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

Emission Control System Warranty

California and United States Emission Control

Defects Warranty Statement

(for Model 68727)

The California Air Resources Board (herein CARB), the United

States Environmental Protection Agency (herein EPA), and Harbor

Freight Tools (herein HFT) are pleased to explain the emission control

system warranty on your 1995 and later Small Off-Road Engine (herein

engine). In California, the engine must be designed, built and equipped

to meet the State’s stringent anti-smog standards. Elsewhere within

the United States, new off-road, spark-ignition engines certified for

model year 1997 and later, must meet similar standards set forth by

the EPA. HFT must warrant the emission control system on your

engine for the periods of time described below, provided there has

been no abuse, neglect or improper maintenance of your engine.

Your emission control system may include parts

such as the carburetor or fuel-injection system, and

the ignition system. Also included may be hoses, belts,

connectors and other emission-related assemblies.

Where a warrantable condition exists, HFT will repair your

engine at no cost to you including diagnosis, parts and labor.

United States Emission Control Defects

Warranty Statement

(for Model 68730)

The United States Environmental Protection Agency (herein EPA)

and Harbor Freight Tools (herein HFT) are pleased to explain the

emission control system warranty on your 1997 and later Small Off-

Road Engine (herein engine). Within the United States, new off-road,

spark-ignition engines certified for model year 1997 and later, must be

designed, built and equipped to meet the stringent anti-smog standards

set forth by the EPA. HFT must warrant the emission control system on

your engine for the periods of time described below, provided there has

been no abuse, neglect or improper maintenance of your engine.

Your emission control system may include parts such as the

carburetor or fuel-injection system, and the ignition system. Also

included may be hoses, belts, connectors and other emission-related

assemblies.

Where a warrantable condition exists, HFT will repair your engine

at no cost to you including diagnosis, parts and labor.

Manufacturer’s Warranty Coverage

The 1995 and later engines are warranted for two

(2) years. If any emission-related part on your engine is

defective, the part will be repaired or replaced by HFT.

SAFETY OPERATION MAINTENANCESETUP

Page 19For technical questions, please call 1-800-520-0882.ITEM 69727

69730

Harbor Freight Tools Emission Control

Defects Warranty Coverage

Engines are warranted for a period of two (2) years relative

to emission control parts defects, subject to the provisions

set forth below. If any emission related part on your engine is

defective, the part will be repaired or replaced by HFT.

Owner’s Warranty Responsibilities

• As the engine owner, you are responsible for the performance

of the required maintenance listed in your Owner’s Manual.

HFT recommends that you retain all receipts covering

maintenance on your engine, but HFT cannot deny warranty

solely for the lack of receipts or for your failure to ensure

the performance of all scheduled maintenance.

• As the engine owner, you should, however, be aware

that HFT may deny you warranty coverage if your engine

or a part has failed due to abuse, neglect, improper

maintenance, or unapproved modifications.

• You are responsible for shipping your engine to a HFT warranty

station as soon as a problem exists. Contact the HFT Customer

Service department at the number below to make shipping

arrangements. The warranty repairs should be completed

in a reasonable amount of time, not to exceed 30 days.

If you have any questions regarding your warranty

rights and responsibilities, you should contact the

Harbor Freight Tools Customer Service Department at 1-800-520-0882.

Harbor Freight Tools Emission Control

Defects Warranty Provisions

1. Length of Coverage

HFT warrants to a first retail purchaser and each

subsequent purchaser that the engine is free from

defects in materials and workmanship that cause the

failure of warranted parts for a period of two (2) years

after the date of delivery to the first retail purchaser.

2. No Charge Repair or Replacement

Repair or replacement of any warranted part will be performed at

no charge to the owner if the work is performed through a warranty

station authorized by HFT. For emissions warranty service,

contact the HFT Customer Service Department at 1-800-520-0882.

3. Consequential Damages Coverage

Coverage under this warranty shall also extend to the failure

of any engine components caused by the failure of any

warranted part while it is still covered under this warranty.

4. Coverage Exclusions

Warranty claims shall be filed in accordance with the provisions

of the HFT warranty policy explained in the box at the top of the

previous page. HFT shall not be liable for any loss of use of

the engine, for any alternative usage, for any damage to goods,

loss of time, or inconvenience. Warranty coverage shall also be

excluded for any part which fails, malfunctions, or is damaged

due to failure to follow the maintenance and operating instructions

set forth in the Owner’s Manual including, but not limited to:

a) Use of parts which are not authorized by HFT

b) Improper installation, adjustment or repair of the engine or of

any warranted part unless performed by an authorized warranty

center

c) Failure to follow recommendations on fuel use contained in the

Owner’s Manual

d) Improper or inadequate maintenance of any warranted parts

e) Repairs performed outside of the authorized warranty

service dealers

f) Alterations by changing, adding to or removing parts from

the engine.

5. Service and Maintenance

Component parts which are not scheduled for replacement

as required maintenance or are scheduled only for regular

inspection to the effect of “repair or replace as necessary”

are warranted for the warranty period. Any warranted part

which is scheduled for replacement as required maintenance

is warranted for the period of time up to the first scheduled

replacement point for that part. Any replacement part, provided

it is equivalent in durability and performance, may be used

in performance of maintenance or repairs. The owner is

responsible for commissioning a qualified technician/mechanic

to perform all required maintenance, as outlined in the

Inspection, Cleaning, and Maintenance section in this manual.

6. Warranted Parts

1) Fuel Metering System

i) Carburetor and its internal parts.

ii) Fuel pump (if so equipped).

iii) Cold start enrichment system.

2) Air Induction System

i) Intake pipe/manifold.

ii) Air cleaner.

3) Ignition System

i) Spark plug.

ii) Magneto ignition system.

4) Catalyst System (if so equipped)

i) Exhaust pipe stud.

ii) Muffler.

iii) Catalytic converter (if so equipped).

5) Miscellaneous Items Used in Above Systems

i) Vacuum, temperature and time sensitive valves and

switches.

ii) Hoses, belts, connectors, and assemblies.

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM

IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR

MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS

QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE

ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY

STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND

LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY

ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS

THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

SAFETYOPERATIONMAINTENANCE SETUP

Page 20 For technical questions, please call 1-800-520-0882. ITEM 69727

69730

Parts Lists and Diagrams

69727 Parts List

Part Description Qty

1 Gasket, Cylinder Head 1

2 Cover Subassembly, Cylinder Head 1

3 Gasket, Cylinder Head Cover 1

4 Tube, Breather 1

5 Bolt 4

6 Stud 1

7 Stud 1

8 Stud 2

9 Pin 2

10 Bolt, Cylinder Head 4

11 Plug, Spark 1

12 Head Subassembly, Cylinder 1

13 Crankcase Subassembly 1

14 Sensor, Engine Oil 1

15 Gear Asm., Governor 1

16 Arm, Governor 1

17 Bolt, Drain Plug 2

18 Washer 2

19 Bearing 1

20 Seal, Oil 1

21 Washer 1

22 Pin 1

23 Bolt 2

24 Cover, Crankcase 1

25 Bearing 1

26 Seal, Oil 1

27 Gasket, Crankcase 1

28 Pin 2

29 Dipstick Subassembly, Oil 1

30 Plug Subassembly, Engine Oil 1

31 Bolt 6

32 Crankshaft Asm. 1

33 Clip, Piston Pin 2

34 Piston 1

35 Pin, Piston 1

36 Rod, Connecting 1

37 Ring, Primary 1

38 Ring, Secondary 1

39 Ring Set, Oil 1

40 Camshaft Asm. 1

41 Valve, Exhaust 1

42 Valve, Intake 1

43 Seat, Valve Spring 1

44 Retainer, Exhaust Valve 1

45 Rotator, Valve 1

46 Guide, Seal 1

47 Tappet, Valve 1

48 Lifter, Valve 2

49 Plate Subassembly, Lifter Stopper 2

50 Bolt, Valve Adjusting 1

51 Rocker, Valve 2

52 Nut, Valve Adjusting 2

53 Nut, Valve Lock 2

54 Spring, Valve 2

55 Starter Asm., Recoil 1

56 Bolt 3

Part Description Qty

57 Shroud 1

58 Shroud, Cylinder Body 1

59 Shield,Lower 1

60 Protector, Oil 1

61 Switch Subassembly, Stop Engine 1

62 Bolt 2

63 Bolt 1

64 Collar 1

65 Bolt 1

66 Bolt 4

67 Carburetor Asm. 1

68 Gasket, Air Cleaner 1

69 Gasket, Carburetor 1

70 Plate, Carburetor Insulator 1

71 Gasket, Carburetor Insulator 1

72 Nut 2

73 Cleaner, Air 1

75 Gasket, Exhaust Outlet 1

76 Nut 2

77 Muffler Asm. 1

78 Bolt 2

79 Gasket, Secondary Supply

Air Valve Flange 1

80 Valve, Muffler Secondary Supply Air 1

81 Tank, Fuel 1

82 Strainer, Fuel 1

83 Cover, Fuel Tank 1

84 Outlet Subassembly, Fuel Tank Oil 1

85 Clamp 4

86 Tube, Fuel 1

87 Bolt 1

88 Nut 2

90 Hose, Vapor Rubber 1

92 Collector, Vapor 1

93 Clamp 1

94 Hose, Air Cleaner Rubber 1

95 Nut, Flywheel 1

96 Pulley, Starter 1

97 Impeller 1

98 Flywheel Subassembly 1

99 Bolt 2

100 Coil, Ignition 1

101 Control Asm., Throttle 1

102 Bolt 2

103 Spring, Governor 1

104 Rod, Governor 1

105 Spring, Throttle Valve Returning 1

106 Bolt, Governor Support 1

107 Nut 1

108 Support Subassembly, Governor 1

109 Valve, One Way 1

110 Clamp 1

111 Cover, Fuel Vapor Collector 1

112 Bolt 2

113 Jacket, Rubber 1

SAFETY OPERATION MAINTENANCESETUP

Page 21For technical questions, please call 1-800-520-0882.ITEM 69727

69730

52

45

49

50

50

44

46

43 54

54 41

42

51

52

53

53

39

33 34

35

36

33

37 38

47

48

47

48

51

16

21

22

15

14

17 18

18

17

20

23

23

19

13

32

56

56

56

55

11

1

4

23

56

8

10

10

10

10

8

7

9

9

5

5

12

40

101

102

102 103

104

105

106

107

108

95

97

99

99

596

98

100

30

31

31

31 31

31

31

24

29

26

25

28

28

27

68

69

70

71

67

57

58

59

60

63

64

61

62

62

65

72

72

73

75

76

76

77

78 78

79

80

66

66

66

66

82

81

84 85

86

85

87

88 88

83

90

85

85

92

93

94

109

112

110

111

112

113

69727 Assembly Diagram

Record Product’s Serial Number Here:

Note: If product has no serial number,

record month and year of purchase instead.

Note: Some parts are listed and shown

for illustration purposes only, and are not

available individually as replacement parts.

SAFETYOPERATIONMAINTENANCE SETUP

Page 22 For technical questions, please call 1-800-520-0882. ITEM 69727

69730

69730 Parts List

Part Description Qty

1 Gasket, Cylinder Head 1

2 Cover Subassembly, Cylinder Head 1

3 Gasket, Cylinder Head Cover 1

4 Tube, Breather 1

5 Bolt 4

6 Stud 1

7 Stud 1

8 Stud 2

9 Pin 2

10 Bolt, Cylinder Head 4

11 Plug, Spark 1

12 Head Subassembly, Cylinder 1

13 Crankcase Subassembly 1

14 Sensor, Engine Oil 1

15 Gear Assy, Governor 1

16 Arm, Governor 1

17 Bolt, Drain Plug 2

18 Washer 2

19 Bearing 1

20 Seal, Oil 1

21 Washer 1

22 Pin 1

23 Bolt 2

24 Cover, Crankcase 1

25 Bearing 1

26 Seal, Oil 1

27 Gasket, Crankcase 1

28 Pin 2

29 Dipstick Subassembly, Oil 1

30 Plug Subassembly, Engine Oil 1

31 Bolt 6

32 Crankshaft Assy. 1

33 Clip, Piston Pin 2

34 Piston 1

35 Pin, Piston 1

36 Rod, Connecting 1

37 Ring, Primary 1

38 Ring, Secondary 1

39 Ring Set, Oil 1

40 Camshaft Assy. 1

41 Valve, Exhaust 1

42 Valve, Intake 1

43 Seat, Valve Spring 1

44 Retainer, Exhaust Valve 1

45 Rotator, Valve 1

46 Guide, Seal 1

47 Tappet, Valve 2

48 Lifter, Valve 2

49 Plate Subassembly, Lifter Stopper 1

50 Bolt, Valve Adjusting 2

51 Rocker, Valve 2

Part Description Qty

52 Nut, Valve Adjusting 2

53 Nut, Valve Lock 2

54 Spring, Valve 2

55 Starter Assy, Recoil 1

56 Bolt 3

57 Shroud 1

58 Shroud, Cylinder Body 1

59 Shield,Lower 1

60 Protector, Oil 1

61 Switch Subassembly, Stop Engine 1

62 Bolt 2

63 Bolt 1

64 Collar 1

65 Bolt 1

66 Bolt 4

67 Carburetor Assy. 1

68 Gasket, Air Cleaner 1

69 Gasket, Carburetor 1

70 Plate, Carburetor Insulator 1

71 Gasket, Carburetor Insulator 1

72 Nut 2

73 Cleaner, Air 1

74 Jacket, Rubber 1

75 Gasket, Exhaust Outlet 1

76 Nut 2

77 Muffler Assy 1

78 Tank, Fuel 1

79 Strainer, Fuel 1

80 Cover, Fuel Tank 1

81 Outlet Subassembly, Fuel Tank Oil 1

82 Clamp 3

83 Tube, Fuel 1

84 Bolt 1

85 Nut 2

86 Nut, Flywheel 1

87 Pulley,Starter 1

88 Impeller 1

89 Flywheel Subassembly 1

90 Bolt 2

91 Coil, Ignition 1

92 Control Assy, Throttle 1

93 Bolt 2

94 Spring, Governor 1

95 Rod, Governor 1

96 Spring, Throttle Valve Returning 1

97 Bolt, Governor Support 1

98 Nut 1

99 Support Subassembly, Governor 1

100 Valve, One Way 1

101 Clamp 1

102 Hose, Fuel Steam Rubber 1

SAFETY OPERATION MAINTENANCESETUP

Page 23For technical questions, please call 1-800-520-0882.ITEM 69727

69730

69730 Assembly Diagram

52

45

49

50

50

44

46

43 54

54 41

42

51

52

53

53

39

33 34

35

36

33

37 38

47

48

47

48

51

16

21

22

15

14

17 18

18

17

20

23

23

19

13

32

56

56

56

55

27

27

37

11

1

4

23

56

8

10

10

10

10

8

7

9

9

5

5

21

40

92

93

93 94

95

96

97

98

99

86

88

90

90

5

75

76 76 77

87

89

91

30

31

31

31 31

31

31

24

29

26

25

28

28

27

75

66

66

66

66

58

62

62

65

63

06

64

59

61

86

96

07

17

76

87

18

28

28

97

80

38

48

58

58

101

201

28 001

47

SAFETYOPERATIONMAINTENANCE SETUP

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 520-0882

Mounting Hole Diagram

6.38 in. / 162mm

2.6 in. / 66mm

1.6 in. / 40.5mm

2.97 in. / 75.5mm

3.17 in. / 80.5mm

Power Take-Off Diagram

2.43 in. / 61.7mm

1.79 in. / 45.5mm

0.67 in.

/ 17mm

5/16-24UNF

Ø0.75 in. / 19.05mm

0.64 in.

/ 16.36mm

0.1875 in. / 4.78mm

4x5/16-24UNF

5/16-24UNF

4.17 in. / 106mm

Ø3.625 in. / 92mm

Note: Not to scale.