Harbor Freight Adjustable Steel Welding Table Product Manual

Manual for the 61369 Adjustable Steel Welding Table 61369 Adjustable Steel Welding Table

: Harbor-Freight Harbor-Freight-Adjustable-Steel-Welding-Table-Product-Manual-724256 harbor-freight-adjustable-steel-welding-table-product-manual-724256 harbor-freight pdf

Open the PDF directly: View PDF .
Page Count: 8

Page 2 For technical questions, please call 1-888-866-5797. Item 61369

Specifications

Table Top Dimensions 30" x 19-7/8"

Table Height 32-7/8"

Maximum Weight Capacity 350 lb

IMPORTANT SAFETY INFORMATION

Assembly Precautions

1. Assemble only according to these instructions.

Improper assembly can create hazards.

2. Wear ANSI-approved safety goggles and

heavy-duty work gloves during assembly.

3. Keep assembly area clean and well lit.

4. Keep bystanders out of the area during assembly.

5. Do not assemble when tired or when under the

influence of alcohol, drugs or medication.

6. Weight capacity and other product capabilities apply

to properly and completely assembled product only.

Use Precautions

1. This product is not a toy. Do not allow

children to play with or near this item.

2. Use as intended only. Do not sit or stand on Table.

3. Inspect before every use; do not use

if parts are loose or damaged.

4. Use only on flat, level, hard surface.

5. Do not exceed listed weight capacity. Tighten

all knobs securely before applying load.

Be aware of dynamic loading!

Sudden load movement may briefly create

excess load causing product failure.

6. Maintain product labels and nameplates.

These carry important safety information.

If unreadable or missing, contact

Harbor Freight Tools for a replacement.

Assembly Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document

including all text under subheadings therein before set up or use of this product.

Note: For additional information regarding the parts listed in the following pages,

refer to the Assembly Diagram near the end of this manual.

Unwrap and separate all parts on a clear work area.

Vertical Post – Angle Bracket Assembly

Attach the two Angle Brackets (6) to the Vertical

Posts (20) using one Washer (7), Nut (8) and

Bolt (9) per Post-Bracket assembly.

See Figure A.

Vertical Post (20)

Angle Bracket (6)

Bolt (9)

Nut (8)

Washer (7)

Figure A

Page 3For technical questions, please call 1-888-866-5797.Item 61369

Support Leg Assembly

Attach the two Vertical Post-Angle Bracket

assemblies from the previous step to the two

Support Legs (13) using four Washers (7),

Nuts (8) and Bolts (12). See Figure B.

Vertical Post – Angle Bracket

Assemblies

Support Legs (13)

Figure B

Bolt (12)

Nut (8)

Washer (7)

Tool Hanger – Support Brace – Angle Handle Assembly

1. Attach the Tool Hanger (16)

to the Support Leg which has

four threaded holes using four

Bolts (15). See Figure C.

2. Attach the Support Brace (21) to the

Vertical Posts using two Washers (7),

Nuts (8) and Bolts (22). See Figure C.

3. Insert a Bolt (12) through the back of

each of the two Angle Adjustment

Handles (10). Slide a Washer (11) over

each Bolt with the cupped side of the

Washer against the Handle. Insert the

Bolts through the Angle Brackets and

thread into the nut welded to the Vertical

Post. See Figure C.

Support Leg (13)

Figure C

Welded nut for

Handle Bolt

Support

Brace (21)

Tool

Hanger

(16)

Angle

Adjustment

Handle (10)

Bolt (12)

Bolt (22)

Bolt (15)

Nut (8)

Washer

(11) Washer (7)

Page 4 For technical questions, please call 1-888-866-5797. Item 61369

Table Top Bracket Assembly

Attach the two Table Top Brackets (4)

to the bottom of the Table Top (1) using

four Washers (2), Nuts (5) and

Bolts (19). Note that the Washers are

placed between the Table Top and the

Table Top Brackets. See Figure D.

Table Top (1)

Table Top

Bracket

(4)

Figure D

Bolt (19)

Nut (5)

Washer

(2)

Attaching the Table Top

The two Angle Brackets each have

five positive stop positions which

allow the Table Top, once attached,

to be positioned at five different

angles. Prior to attaching the Table

Top, ensure that the Brackets are

set in the middle position and that

the Angle Adjustment Handles are

tightened securely. See Figure E.

1. With assistance, lift the Table

Top and place in position over

the upright table stand.

2. Insert four Bolts (3) through the Angle

Brackets and Table Top Brackets

and secure in place using four

Washers (7) and Nuts (8). Tighten

all hardware. See Figure E.

Angle

Adjustment

Handle (10)

Bolt (3)

Washer (7)

Table Top

Bracket

(4) Table

Top

(1)

Angle

Bracket

(6)

Nut (8)

Figure E

Page 5For technical questions, please call 1-888-866-5797.Item 61369

Installing the Guide Rails

1. Place four Washers (2)

on the shafts of the four

Lever Bolts (17).

2. Attach the Short Guide Rail (23)

and the Long Guide Rail (18) in

the desired position on the Table

Top using the four Lever Bolts

and Washers. See Figure F.

Maintenance

Inspection, Maintenance, and Cleaning

1. BEFORE EACH USE, inspect the general

condition of the Welding Table. Check for:

• loose hardware

• misalignment or binding of parts

• cracked or broken parts

• any other condition that may

affect its safe operation.

2. AFTER USE, wipe external surfaces

of the Table with clean cloth.

Lever Bolt (17) Short Guide

Rail (23)

Long Guide

Rail (18)

Table Top (1)

Figure F

Washer (2)

Page 6 For technical questions, please call 1-888-866-5797. Item 61369

Part Description Qty

1Table Top 1

2Washer Ø6.5 x 1.5 mm 8

3 Bolt M8 x 20 mm 4

4Table Top Bracket 2

5 Nut M5 mm 8

6 Angle Bracket 2

7Washer Ø8.5 x 1.2 mm 12

8 Nut M8 mm 12

9 Bolt M8 x 45 mm 2

10 Angle Adjustment Handle 2

11 Washer Ø8.5 x 1.8 mm 2

12 Bolt M8 x 50 mm 6

Part Description Qty

13 Support Leg 2

14 Plastic Foot 4

15 Bolt M6 x 20 mm 4

16 Tool Hanger 1

17 Lever Bolt M6 x 12 mm 4

18 Long Guide Rail 1

19 Bolt M5 x 10 mm 4

20 Vertical Post 2

21 Support Brace 1

22 Bolt M8 x 65 mm 2

23 Short Guide Rail 1

Record Serial Number Here:

Note: If product has no serial number, record month and year of purchase instead.

Note: Some parts are listed and shown for illustration purposes only, and

are not available individually as replacement parts.

Parts List and Diagram

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM

IN THIS DOCUMENT AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR

MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS

QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE

ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY

STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND

LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY

ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS

THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Parts List

Page 7For technical questions, please call 1-888-866-5797.Item 61369

Assembly Diagram

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,

and warrants to the original purchaser that this product is free from defects in materials and workmanship for the

period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,

to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper

installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries

to persons or property, or for incidental, contingent, special or consequential damages arising from the use of

our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the

above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER

WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with transportation charges

prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.

If our inspection verifies the defect, we will either repair or replace the product at our election or we may

elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will

return repaired products at our expense, but if we determine there is no defect, or that the defect resulted

from causes not within the scope of our warranty, then you must bear the cost of returning the product.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797