Harbor Freight Air Grease Gun With 6 In Extension Product Manual
Manual for the 219 Air Grease Gun 00219 Air Grease Gun - Save on this Pneumatic Air Grease Gun
2015-05-27
: Harbor-Freight Harbor-Freight-Air-Grease-Gun-With-6-In-Extension-Product-Manual-723430 harbor-freight-air-grease-gun-with-6-in-extension-product-manual-723430 harbor-freight pdf
Open the PDF directly: View PDF 
.
Page Count: 11
| Download | |
| Open PDF In Browser | View PDF |
AIR GREASE GUN Model 00219 ASSEMBLY and OPERATING INSTRUCTIONS Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Distributed exclusively by Harbor Freight Tools®. 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result in serious injury. Save this manual. Copyright© 2004 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions or replacement parts, please call 1-800-444-3353. REV 11h Specifications Air Inlet Maximum Air Pressure Capacity Flex Hose Length Air Consumption Recommended Hose Size Stiff Nozzle Length Canister Dimensions Air Inlet Screen Spout Tip Dimensions 1/4” - 18 NPT Female 100 PSI 400 cc Bulk, 14 oz. Canister 9” L 4 CFM @ 90 PSI 3/8” 6” 10-7/8” x 2-1/4” Dia. 20 Mesh 1-1/2” L x 9/16” Dia. Save This Manual You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep the manual and invoice in a safe and dry place for future reference. Safety Warnings and Precautions WARNING: When using tool, basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment. Read all instructions before using this tool! 1. Keep work area clean. Cluttered areas invite injuries. 2. Observe work area conditions. Do not use machines or power tools in damp or wet locations. Don’t expose to rain. Keep work area well lit. 3. Keep children away. Children must never be allowed in the work area. Do not let them handle machines, tools, extension cords, or air hoses. 4. Store idle equipment. When not in use, tools must be stored in a dry location to inhibit rust. Always lock up the Air Grease Gun and the grease, in a location that is out of reach of children. 5. Use the right tool for the job. Do not attempt to force a small tool or attachment to do the work of a larger industrial tool. There are certain applications for which this tool was designed. It will do the job better and more safely at the rate for which it was intended. Do not modify this tool and do not use this tool for a purpose for which it was not intended. 6. Dress properly. Do not wear loose clothing or jewelry as they can be caught in moving parts. Protective, electrically non-conductive clothes and non-skid footwear are recommended when working. Wear restrictive hair covering to contain long hair. REV 05g SKU 00219 For technical questions, please call 1-800-444-3353. Page 2 7. Use eye and ear protection. Always wear ANSI approved impact safety goggles. Wear an ANSI approved dust mask or respirator when working around chemical dusts and mists. 8. Do not overreach. Keep proper footing and balance at all times. Do not reach over or across running machines or air hoses. 9. Maintain tools with care. Keep tools clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords and air hoses periodically and, if damaged, have them repaired by an authorized technician. The handles must be kept clean, dry, and free from oil and grease at all times. 10. Disconnect air supply. Disconnect air hose and turn off the compressor when not in use. 11. Remove adjusting keys and wrenches. Check that keys and adjusting wrenches are removed from the tool or machine work surface before plugging it in. 12. Avoid unintentional starting. Do not carry any tool with your finger on the trigger, whether it is connected to the air compressor or not. 13. Stay alert. Watch what you are doing, use common sense. Do not operate any tool when you are tired. 14. Check for damaged parts. Before using any tool, any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment and binding of moving parts; any broken parts or mounting fixtures; and any other condition that may affect proper operation. Any part that is damaged should be properly repaired or replaced by a qualified technician. Do not use the tool if any switch does not turn On and Off properly. 15. Guard against electric shock. Prevent body contact with grounded surfaces such as pipes, radiators, ranges, and refrigerator enclosures. 16. Replacement parts and accessories. This product is to be repaired and serviced only by a qualified technician. When this product is serviced, only identical replacement parts should be used. Use of any other parts will void the warranty. Only use accessories intended for use with this tool. Approved accessories are available from Harbor Freight Tools. 17. Do not operate tool if under the influence of alcohol or drugs. Read warning labels if taking prescription medicine to determine if your judgement or reflexes are impaired while taking drugs. If there is any doubt, do not operate the Grease Gun. 18. Use proper size and type extension cord. If an extension cord is required, it must be of the proper size and type to supply the correct current to the air compressor without heating up. Otherwise, the extension cord could melt and catch fire, or cause electrical damage to the tool. Check your air compressor’s manual for the appropriate size cord. 19. Maintenance. The maintenance outlined in the maintenance section should be performed regularly. For your safety, this product should be serviced or repaired regularly only by a qualified technician. 20. Compressed air only. Never use combustible gas as a power source. SKU 00219 For technical questions, please call 1-800-444-3353. Page 3 21. Check hoses carefully. Never use the Grease Gun if the hoses are cracked, frayed, or kinked. Avoid problems by not severely bending the hoses. If hoses appear damaged, have them replaced. 22. This Grease Gun is designed only to hold and dispense grease. Never use it to hold and dispense any other material. Note: Performance of the compressor (if powered by line voltage) may vary depending on variations in local line voltage. Extension cord usage may also affect tool performance. Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Unpacking When unpacking, check to make sure the parts listed on page 9 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. Operation Grease Gun 1/4”-18 NPT Female For best service you should incorporate an oiler, regulator, and inline filter, as shown in the diagram above. Hoses, couplers, oilers, regulators, and filters are all available at Harbor Freight Tools. 1. If desired, for quick tool connection, you will need to prepare a 1/4” quick air connector (not included) to connect to the air source hose. First, wrap the 1/4” quick air connector (not included) with pipe thread seal tape (not included) before threading it onto the 3/8” air source hose. Then, connect the 1/4” quick air connector to the Air Inlet (2) on the Grease Gun. Note: If you are not using an automatic oiler system, before operation, add a few drops of Pneumatic Tool Oil to the airline connection. Add a few drops more after each hour of continual use. 2. To check your air system, set the air pressure on your compressor to 90 PSI. Do not exceed the testing air pressure of 90 PSI. 3. Check the air connection for leaks. After test is complete, disconnect from the air supply until grease is loaded into the Air Grease Gun. SKU 00219 For technical questions, please call 1-800-444-3353. Page 4 FIGURE A Front Housing (7) Rear Housing (1) Joint (8) Air Inlet (2) Rigid Coupler Assy. (9) Trigger (3) Handle (21) Flexible Hose Assy. (9b) Follower Rod (19) Tube (18) FIGURE B FIGURE C Top of Tube (18) on the Head (7) Locking Plate (20) Air Vent (11) Fill Nozzle (10) Handle (21) REV 05g SKU 00219 For technical questions, please call 1-800-444-3353. Page 5 Grease Loading Instructions Warning!! Make sure the Grease Gun is not attached to the air source hose when loading grease. Grease can be loaded into the Grease Gun by loading with a filler pump (FIGURE 1), using suction filling (FIGURE 2), or loading with a cartridge (FIGURE 3). Loading a grease cartridge (not included). See the Assembly Drawing on page 10, Figures A, B, and C on page 5 and FIGURE 3 below. 1. 2. Remove the Tube (18) from the top of the Front Housing (7). Pull back on the Handle (21) until it is fully extended. Lock it into place with the Locking Plate (20). 3. Remove the caps/lids from both ends of the cartridge (not included). Insert the cartridge into the Tube (18) in the orientation indicated on the cartridge, making sure that it is in as far as possible. 4. Reassemble the Tube (18) to the top on the Front Housing (7). Press the Locking Plate (20) and release the Handle (21). Press the Handle (21) in as far as it will go. FIGURE 1 FIGURE 2 FIGURE 3 Cartridge Filler Hose with Plug on the Pump (not included) enters the Nozzle (10) Nozzle (10) Tube (18) Filler Pump Filling Suction Filling Cartridge Filling Suction Filling (FIGURE 2) See the Assembly Drawing on page 10, Figures A, B, and C on page 5 and FIGURE 2 above. 1. 2 3. 4. Remove the Tube (18) from the top of the Front Housing (7). Submerge the open end of the Tube (18) approximately 2 inches into the grease container (not included). Slowly, pull back and fully extend the Handle (21) to draw grease upward into the Tube (18). When the Handle (21) is fully extended, lock it into place with the Locking Plate (20). Carefully, reassemble the Tube (18) to the top on the Head (7). Press the Locking Plate (20) and release the Handle (21). Press the Handle (21) in as far as it will go. REV 05g SKU 00219 For technical questions, please call 1-800-444-3353. Page 6 Loading with a Filler Pump (not included) See the Assembly Drawing on page 10, Figures A, B, and C on page 5 and FIGURE 1 on page 6. 1. 2. 3. 4. 5. Slowly, pull back and fully extend the Handle (21). Lock it into place with the Locking Plate (20). Insert the Filler Plug on the end of the hose of the Filler Pump (not included) into the Nozzle (10). Follow the instructions provided in the Filler Pump manual (not included) to operate the Filler Pump until the Tube (18) is full. Disconnect the Grease Gun from the Filler Pump (not included). Press the Locking Plate (20) and release the Handle (21). Press the Handle (21) in as far as it will go. Operating the Grease Gun Note: If your application requires the Flexible Hose (9b), attach it to the Rigid Coupler (9). Note: If your Grease Gun fails to work, it is usually because air pockets have formed in the Gun. To remove them, disconnect the Grease gun from the air supply. Pull back and fully extend the Handle (21). Now push the Handle forward into the Grease Tube while depressing the Air Vent Valve (11). Reconnect the air supply to the Grease gun and then squeeze and release the Trigger (3) several times until the trapped air is expelled. Repeat as needed. See FIGURE C on page 5. Before every use, prime the Grease Gun by operating the Gun (see below) until grease flows from the tip. If it does not prime properly, follow the directions above for venting trapped air. 1. Attach the Grease Gun to the air source hose following the directions on page four. Set the air compressor to 30 - 100 PSI. Squeeze the Trigger (3) to inject a small amount of grease. Release and squeeze the trigger repeatedly to inject more grease. Disconnect from the air source hose before refilling the Grease Gun. Turn off the air compressor. Warning!! The Grease Gun may still have air pressure after disconnected from the air source. Point the Grease Gun into a suitable receptacle and fire it until all of the air is expended. 2. 3. SKU 00219 For technical questions, please call 1-800-444-3353. rev 05i; 06g Page 7 Troubleshooting If the Grease Gun does not operate: 1. 2. Check that gun is properly connected to the air source and the air compressor is set to 30 - 100 PSI. If it still doesn’t operate, take it to an qualified service technician to check the Springs (6 and 17), and the Piston Assembly (5). If the Grease Gun cycles and does not pump grease: 1. 2. 3. Repeat priming operation on page 7. Check to see if you are out of grease. Disconnect any extensions and prime until grease flows. If the Grease Gun continues to lose prime: 1. 2. 3. Release trapped air. Refill the Grease Gun and repeat priming. Have an qualified service technician check the position on the Follower Assembly. If the Grease Gun still doesn’t operate, contact a qualified service technician. Maintenance Always disconnect from the air source hose before attempting any maintenance. 1. 2. 3. After each use, clean leftover grease from the Tube (18). Make sure the Nozzle (10) and the tip of the Grease Gun are clear of dirt, grease, or any debris. Wipe down the unit with a lint free cloth. SKU 00219 For technical questions, please call 1-800-444-3353. REV 09b Page 8 Parts List Part Description Q’ty 1 Rear Housing 1 2 Air Inlet 1 3 Trigger Assembly 1 4 Pan HD Screw 4 5 Piston Assembly 1 6 Spring 1 7 Front Housing 1 8 Joint 1 9 Rigid Coupler Assembly 1 9b Flexible Hose Assembly 1 10 Fill Nozzle 1 11 Air Vent Valve 1 12 Gasket 1 13 Lock Nut 1 14 Plunger 1 15 O-Ring 1 16 Backlash Gasket 1 17 Large Spring 1 18 Tube 1 19 Follower Rod 1 20 Locking Plate 1 21 Handle 1 PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. rev 05g; 06g SKU 00219 For technical questions, please call 1-800-444-3353. Page 9 Assembly Drawing REV 05g SKU 00219 For technical questions, please call 1-800-444-3353. Page 10 90 day warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. This warranty is expressly in lieu of all other warranties, express or implied, including the warranties of merchantability and fitness. To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. 3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353 SKU 00219 For technical questions, please call 1-800-444-3353. REV 11h Page 11
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 4.1-c037 46.282696, Mon Apr 02 2007 18:36:42 Instance ID : uuid:2e6623a7-e004-4e7e-aaeb-52c39572ac4e Document ID : adobe:docid:indd:48b3aa43-6d52-11dc-a7bb-e880d5d6e95a Rendition Class : proof:pdf Manifest Link Form : DirectStream, DirectStream, DirectStream, DirectStream Manifest Placed X Resolution : 72.00, 72.00, 299.91, 299.91 Manifest Placed Y Resolution : 72.00, 72.00, 299.91, 299.91 Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches Manifest Reference Instance ID : uuid:33f4e2e5-96a1-11d8-a315-aff6b4adb132, uuid:cbc035b1-96a4-11d8-a315-aff6b4adb132, uuid:cd3162ff-fdeb-11d9-bdf9-85977da3aeef, uuid:20149665-fdef-11d9-bdf9-85977da3aeef Manifest Reference Document ID : adobe:docid:photoshop:33f4e2e4-96a1-11d8-a315-aff6b4adb132, adobe:docid:photoshop:cbc035b0-96a4-11d8-a315-aff6b4adb132, adobe:docid:photoshop:cd3162fd-fdeb-11d9-bdf9-85977da3aeef, adobe:docid:photoshop:f8f004fa-fd33-11d9-822a-b05622f04bfc Create Date : 2011:08:08 08:35:37-07:00 Modify Date : 2011:08:08 08:35:39-07:00 Metadata Date : 2011:08:08 08:35:39-07:00 Creator Tool : Adobe InDesign CS3 (5.0.4) Thumbnail Format : JPEG Thumbnail Width : 256 Thumbnail Height : 256 Thumbnail Image : (Binary data 9916 bytes, use -b option to extract) Format : application/pdf Producer : Adobe PDF Library 8.0 Trapped : False Page Count : 11 Creator : Adobe InDesign CS3 (5.0.4)EXIF Metadata provided by EXIF.tools