Harbor Freight Bigfoot Panel Wagon Product Manual

Manual for the 60570 Bigfoot Panel Wagon 60570 Bigfoot Panel Wagon

: Harbor-Freight Harbor-Freight-Bigfoot-Panel-Wagon-Product-Manual-724176 harbor-freight-bigfoot-panel-wagon-product-manual-724176 harbor-freight pdf

Open the PDF directly: View PDF .
Page Count: 4

Page 2 For technical questions, please call 1-800-444-3353. Item 60570

Specifications

Tires 10″ Pneumatic

Age Range 5 and up

Weight Capacity 330 lb.

Deck Size 33-5/8″ x 15-3/4″ x 5-1/2″

Inside Dimensions 31-7/8″ x 13-3/4″ x 4″

Replacement Wheels Harbor Freight Item 30900

IMPORTANT SAFETY INFORMATION

Read all safety warnings and instructions.

Failure to follow the warnings and instructions may result in serious injury.

Save all warnings and instructions for future reference.

1. AGES 5 AND UP ONLY.

Do not allow younger children to use.

2. WEAR PROPER SAFETY HELMET AND

COMPLETE SAFETY GEAR WHEN RIDING.

Responsible adult must supervise during use.

Use as intended only.

Rider must stay seated at all times during use.

Do not allow more than one child

to play with tricycle at once.

3. Do not use in unstable or dangerous area.

Tipping over can cause injury.

Do not use in areas where vehicles may be present,

such as parking areas, driveways, or roads.

4. Wear ANSI-approved safety goggles

and work gloves during assembly.

5. Read manual before assembly and/or use.

6. Do not exceed 330 lb. capacity.

7. Inspect before every use;

do not use if parts loose or damaged.

Check and tighten hardware periodically.

8. Assemble completely according to instructions

before allowing a child to play with this product.

Assembly

Note: For additional information regarding the parts listed in the following

pages, refer to the Assembly Diagram on facing page.

Note: Do not overtighten hardware.

1. With the Tray (A) upside down so the bottom is facing

upward, place it over saw horses or sturdy cartons.

2. Attach the Rear Axle Assembly (H) to the

Tray (A) using two 1/2″ Bolts. Line up the

Rear Axle Assembly with the holes located at the

very back of the Wagon. Insert the Bolt so that the

small washers, small lock washers and cap nuts

are screwed on from the underside of the wagon.

3. Slide each of the Rear Axle Braces (I) over the end

of each Rear Axle until they sit firmly to the inside

of the Rear Axle Assembly (H). Line up the end of

the Braces with the holes in the wagon. Using two

1/2″ Bolts, insert the bolts from the top of the wagon

so that the small washers, lock washers and the

nut are secured on the underside of the wagon.

4. Attach the Turntable (D) to the Steering Assembly (J).

Attach the Steering Assembly to the Turntable

using the 1-1/8″ Bolt with Hole. Slide the Bolt

through the underside of the Steering Assembly (J)

and into the Turntable (D). Secure it from inside

the Turntable with the 7/8″ Washer, the Large

Lock Washer and the Hex Nut. Loosely thread

the Hex Nut onto the Bolt. Insert the Cotter Pin

through the hole and spread it open.

5. Attach both parts (now one assembled unit as

shown in Step 4) – the Steering Assembly (J) and

the Turntable (D), to the Tray (A). Insert each of the

four 1/2″ Bolts from the top of the wagon and tighten

it into place from the bottom of the Tray with four (4)

small washers, four small lock washers and four nuts.

Page 3For technical questions, please call 1-800-444-3353.Item 60570

6. Slide each of the four Wheels (C) onto

an axle with the Air Valve facing out.

Slide one 1-1/4″ Washer onto each axle.

7. Attach each of the four Axle Caps to the Axles.

8. Insert the lower part of the Handle (B) into the

Steering Assembly (J). Slide the 2-5/8″ Bolt into

the Assembly and through the Handle so that it

exits the other side of the Assembly. Tighten the

Bolt into place with a Small Washer and Nut Cap.

9. Turn the Wagon upright. Attach one (1) of the

Long Side Panels (E) to the wagon with the

three 1-3/4″ Bolts going through both the Tray

and each vertical slat. The top of the Bolts

should be on the inside of the Tray. Tighten

each into place with a washer then a Nut Cap.

Note: The Short Front Panel (G) is the one

with a downward curved front slat.

10. Attach the Short Rear Panel (F) to the wagon

with two 1-3/4″ Bolts going through the Tray (A)

and each vertical slat. Tighten into place by

sliding on the washer followed by the Nut Cap.

11. Attach the second Long Side Panel (E) as in step 9.

Attach the Short Front Panel (G) with two 1-3/4″

Bolts. Tighten into place with the Washer

and Nut Cap as previously described.

Parts List and Diagram

Part Description Qty

A Tray 1

BHandle 1

C Wheel 4

D Turntable 1

E Long Side Panel 2

F Short Rear Panel 1

G Short Front Panel 1

HRear Axle Assembly 1

IRear Axle Braces 2

JSteering Assembly 1

Part Description Qty

K Assembly Hardware set contains: -

1-3/4″ M6 Round Head Bolt Set* 10

2-5/8″ M6 Round Head Bolt Set* (handle) 1

1/2″ M6 Bolt Set* (axle, steering yoke) 8

Axle Washer 4

Axle Caps 4

1-1/8″ Bolt with hole 1

Bolt Cotter Pin 1

7/8″ Turntable Washer 1

Turntable Lock Washer 1

Turntable Nut 1

*Bolts include flat washer and nut.

Record Product’s Serial Number Here:

Note: If product has no serial number,

record month and year of purchase instead.

Note: Some parts are listed and shown

for illustration purposes only and are not

available individually as replacement parts.

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353

Operation

Your Wagon has a long handle mounted at the front.

Use the handle to pull the wagon to your destination,

as well as transporting loads to and from your destination.

Turning the Handle (B) will cause the front wheels on

the wagon to turn. Turn the Handle in the direction

that you wish the wagon to go. The Handle can be

raised for steering from inside the wagon, or lowered

so that the wagon can be pulled from in front.

Maintenance

1. Periodically check tire inflation

(maximum tire inflation is: 30 PSI for rear tires,

35 PSI for front tire).

2. Periodically lubricate wheel axles.

3. Check and tighten hardware periodically.

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM

IN THIS DOCUMENT AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR

MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS

QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE

ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY

STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND

LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY

ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS

THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original

purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty

does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal

activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or

property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion

or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY

IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of

purchase date and an explanation of the complaint must accompany the merchandise. If our inspection verifies the defect, we will

either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly

provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that

the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state.