Harbor Freight Digital Inspection Camera Product Manual
Manual for the 61839 Digital Inspection Camera 61839 Digital Inspection Camera
2015-05-27
: Harbor-Freight Harbor-Freight-Digital-Inspection-Camera-Product-Manual-723513 harbor-freight-digital-inspection-camera-product-manual-723513 harbor-freight pdf
Open the PDF directly: View PDF 
.
Page Count: 12
| Download | |
| Open PDF In Browser | View PDF |
Owner’s Manual & Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference. ITEM 61839 REV 14e Visit our website at: http://www.harborfreight.com Email our technical support at: productsupport@harborfreight.com ITEM 61839 When unpacking, make sure that the product is intact and undamaged. If any parts are missing or broken, please call 1-888-866-5797 as soon as possible. Copyright© 2014 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included. Read this material before using this product. Failure to do so can result in serious injury. SAVE THIS MANUAL. Important Safety Information Work Area Safety 1. Keep your work area clean and well lit. Cluttered benches and dark areas may cause accidents. 6. This product is not a toy. Do not allow children to play with or near this item. 2. Operate the Camera in a well-ventilated work area. 8. Inspect before every use; do not use if parts are loose or damaged. 7. Use as intended only. 3. Do not operate the Camera in explosive 9. Maintain product labels and atmospheres, such as in the presence of nameplates. These carry flammable liquids, gases, or heavy dust. important safety information. 4. Keep a fire extinguisher suitable for If unreadable or missing, contact gasoline/chemical/electrical fires nearby. Harbor Freight Tools for a replacement. 5. Keep bystanders, children and visitors away while operating the Camera. Electrical Safety 1. Before inspecting walls, shut off the circuit breakers to the whole house. 2. 3. 4. 5. 6. Do not expose the Handheld Display Unit to rain or wet conditions. Water entering the Handheld Before inspecting pipes that may Display Unit will increase the contain an electric charge, have them risk of electric shock. checked by a qualified electrician. 7. Do not place the Imager Head Before inspecting an engine, and Cable into any place that may turn off the automobile. contain a live electric charge or Do not use the Camera moving parts, which increases while standing in water. the risk of electric shock. Avoid body contact with grounded 8. Make sure your hands are dry surfaces such as pipes, radiators, before operating the Camera ranges and refrigerators. or charging the battery. Page 2 For technical questions, please call 1-888-866-5797. Item 61839 Camera Safety 1. The Handheld Display Unit is not waterproof. The Imager Head and Cable are rated to IP67. See “Specifications” on page 4. 5. Do not use excessive force to insert or withdraw the Imager Head and Cable. 2. Do not use the Camera if condensation forms in the Imager Head. Let condensation evaporate before use. 7. Do not place the Camera on any unstable cart or surface. 3. Do not submerge the Imager Head and Cable into corrosive substances, such as drain cleaner. 4. Do not get gasoline or oil on the Imager Head and Cable. 6. Do not use the Camera near moving machinery. 8. Handle the Camera with care. If the Camera is dropped, check for breakage and any other conditions that may affect its operation. 9. Store the Camera, cables and accessories in a locked area out of the reach of children. Personal Safety 1. Wear ANSI-approved safety goggles during use. 2. Do not wear loose clothing or jewelry. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts. 3. Do not use the Camera while tired or under the influence of drugs, alcohol, or medications. A moment of interruption can result in serious personal injury. 4. Do not over-reach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the Camera in unexpected situations. 5. Do not use the Camera for personal inspection or medical use in any way. This is not a medical camera. 6. WARNING: Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling. (California Health & Safety Code § 25249.5, et seq.) 7. People with pacemakers should consult their physician(s) before use. Electromagnetic fields in close proximity to heart pacemaker could cause pacemaker interference or pacemaker failure. 8. The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Service There are no user serviceable parts. Camera service must be performed only by qualified repair personnel. Item 61839 For technical questions, please call 1-888-866-5797. Page 3 Specifications Battery Type Display Screen Handheld Display Unit Operating Temperature Imager Head Imager Head Lights Image Sensor Imager Head Ingress Protection Rating Imager Head and Cable Operating Temperature Video Output Page 4 4 x AA 1.5V Alkaline (sold separately) 2.4" TFT LCD (320 x 240) 32°F to 113°F 8.5mm (0.3") 4 x Adjustable LED 1/6" VGA CMOS IP67 - Protected against the effect of immersion between 15cm and 1m 14°F to 176°F RCA Cable For technical questions, please call 1-888-866-5797. Item 61839 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Item 61839 For technical questions, please call 1-888-866-5797. Page 5 Setup- Before Use: Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document including all text under subheadings therein before set up or use. Components RCA Video Out Port Cable Connector Display Screen Cable Handheld Display Unit Imager Head with Light Hook Mirror Magnet RCA Cable Figure A Page 6 For technical questions, please call 1-888-866-5797. Item 61839 Installing Batteries CAUTION: Position batteries in proper polarity and do not install batteries of different types, charge levels, or capacities together. 2. Slide the battery case back in and replace the Battery Cover. The battery compartment is located on the bottom of the handle. 1. Slide the Battery Cover off, remove the battery case, insert four AA batteries (not included). Figure B: Battery Cover Tool Set Up TO PREVENT SERIOUS INJURY FROM ELECTRICAL SHOCK: Make sure that the Camera is OFF before performing any procedure in this section. 1. Connecting Cable: 3. Attaching Accessories: a. Carefully push Cable’s key into Cable Connector’s slot. b. Turn Cable Connector counterclockwise until the Cable and Cable Connector are securely attached. 2. Disconnecting Cable: a. Hold the accessory against the Imager Head, placing the Hook in the hole. b. Match the slot on the Sleeve to the accessory, then slide the Sleeve down the Imager Head until it covers the Hook. a. Turn Cable Connector clockwise until the Cable and Cable Connector are detached. b. Remove Cable. Slot Sleeve Accessory Hook Key Imager Head Cable Figure D 4. Connecting to External Monitor with RCA Cable: Cable Connector Figure C Item 61839 Plug one end into the RCA Video Out Port on Camera, then plug other end into RCA Video In Port on monitor. For technical questions, please call 1-888-866-5797. Page 7 Operating Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document including all text under subheadings therein before set up or use of this product. TO PREVENT SERIOUS INJURY AND DEATH: Always wear eye protection. Wear ANSI-approved safety goggles during use. Before inspecting walls, shut off the circuit breakers to the whole house. Before inspecting pipes that may contain an electric charge, have them checked by a qualified electrician. Before inspecting an engine, turn off the automobile. Handheld Display Unit Controls Power Brighten Light Flip Image Dim Light Figure E Page 8 For technical questions, please call 1-888-866-5797. Item 61839 General Operating Instructions Live Viewing View on Display Screen or use RCA cable to view on external monitor. 1. Press the Power button to turn the Camera on. 2. Adjusting Light: Press Left button to dim and turn off light. Press Right button to turn on light and increase brightness. Item 61839 3. Flip Image: Press the Flip Image button to flip image horizontally and vertically. 4. When finished, press the Power button to turn the Camera off, then clean and store according to “Inspection and Maintenance” on page 10. For technical questions, please call 1-888-866-5797. Page 9 Inspection and Maintenance Procedures not specifically explained in this manual must be performed only by a qualified technician. TO PREVENT SERIOUS INJURY FROM ELECTRICAL SHOCK: Make sure that the Camera is OFF before performing any procedure in this section. TO PREVENT SERIOUS INJURY FROM TOOL FAILURE: Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use. Inspection 1. BEFORE EACH USE, inspect the general condition of the tool. Check for: • cracked or broken parts, and • any other condition that may affect its safe operation. • condensation in Imager Head, • cracked or damaged Cable, Cleaning and Storage 1. AFTER USE, use a mild detergent on a clean cloth to remove any oil, grease or dirt from the Camera, especially on the buttons and ports, being careful to not put excessive pressure on the Display Screen. 2. Remove batteries before storage. 3. Store the Camera, cables and accessories in a locked area out of the reach of children. Troubleshooting Problem Possible Causes Display is on, but does not show image. Likely Solutions 1. Cable connection loose. 1. Check that cable is connected. 2. Imager Head is dirty. 2. Clean Imager Head. Low Batteries. Replace Batteries. 1. Light is dim at maximum brightness. 2. Display turns itself off. 3. Camera will not turn on. Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect power supply before service. Page 10 For technical questions, please call 1-888-866-5797. Item 61839 PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST IN THIS DOCUMENT AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. Parts List Part 1 2 3 4 5 6 7 Description Handheld Display Unit Cable with 8.5mm Imager Head RCA Cable 45° Mirror Accessory Hook Accessory Magnet Accessory Storage Case Qty 1 1 1 1 1 1 1 Record Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Item 61839 For technical questions, please call 1-888-866-5797. Page 11 Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS. To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. 3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : Yes Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.5-c021 79.154911, 2013/10/29-11:47:16 Instance ID : uuid:73bccd74-d753-5e42-a22c-2b9b8b747894 Original Document ID : adobe:docid:indd:3d8405b6-7ee1-11df-9488-aa083f618b49 Document ID : xmp.id:245c49a8-eb5a-45b1-89f2-ab19e18f859d Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:ddde2da0-5b71-439b-9a3d-be1a392b78d9 Derived From Document ID : xmp.did:16584962-eb80-47ca-919f-714fa11d920f Derived From Original Document ID: adobe:docid:indd:3d8405b6-7ee1-11df-9488-aa083f618b49 Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CC (Macintosh) History Changed : / History When : 2014:05:02 11:24:06-07:00 Create Date : 2014:05:02 11:24:06-07:00 Modify Date : 2014:05:02 11:24:07-07:00 Metadata Date : 2014:05:02 11:24:07-07:00 Creator Tool : Adobe InDesign CC (Macintosh) Format : application/pdf Creator : Adobe Rights : Copyright©2014 by Harbor Freight Tools®. All rights reserved. No portion of this document or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Subject : 02.02.09.05 Web Statement : http://www.harborfreight.com Marked : True Producer : Adobe PDF Library 11.0 Trapped : False Page Count : 12 Author : AdobeEXIF Metadata provided by EXIF.tools