Harbor Freight Folding Pet Kennel Crate With Tray Product Manual

Manual for the 96341 Folding Pet Kennel Crate with Tray 96341 Folding Pet Kennel Crate with Tray

2015-05-27

: Harbor-Freight Harbor-Freight-Folding-Pet-Kennel-Crate-With-Tray-Product-Manual-724116 harbor-freight-folding-pet-kennel-crate-with-tray-product-manual-724116 harbor-freight pdf

Open the PDF directly: View PDF PDF.
Page Count: 4

Page 2
For technical questions, please call 1-800-444-3353.
Item 96341
IMPORTANT SAFETY INFORMATION
Assembly Precautions
1.
Assemble only according to these instructions.
assembly can
create hazards.
2.
Wear ANSI-approved safety
goggles and
heavy-duty
work
gloves during assembly.
3.
Avoid sharp edges when assembling kennel crate.
4.
Keep assembly area clean and well lit.
5.
Keep bystanders out of the area during
assembly.
6.
Do not assemble when tired or when under the
influence of alcohol, drugs or medication.
Use Precautions
1.
Check kennel lock and assembly latches before use.
2.
Use extreme caution when transporting animal
in Kennel Crate. Do not carry Crate with
animal inside. Animal may be injured.
3.
For small animals only. Maximum weight should not
exceed 40 Lb. Do not use to shelter wild animals.
4.
For temporary use only. Do not use Kennel
Crate as a permanent pet shelter.
5.
Do not leave kennel with a pet inside locked in hot
car. Leave water and food inside Crate for pets.
6.
This product is not a toy. Do not allow
children to play with or near this item.
7.
Use as intended only.
8.
Inspect before every use; do not use
if parts are loose or damaged.
Assembly Instructions
Read the
ENTIRE
IMPORTANT SAFETY INFORMATION
section at the beginning of this document
including all text under subheadings therein before set up or use of this product.
Note:
The Folding Kennel Crate comes collapsed
The Folding Kennel Crate comes collapsed
for ease of transportation and storage.
1.
Unlock the Hook Latch (6) on the side of the Crate.
Hook
Latch (6)
Figure
A
2.
Unfold the Crate’s Top Panel (12) and then pull up.
Figure
B
3.
Once the Kennel Crate frame is upright, raise the
Back Panel (9) and snap it into place against the Side
Door Frame (4), Side Panel (10) and Top Panel (12).
Figure
C
4.
Lift Front Door Frame (3) with Front Door (1)
and snap into Latch (2) and snap it into place
against the Side Door Frame (4), Side
Panel
(10)
and Top Panel (12). The Front Door (1) is
equipped with a Hook Latch (6) that can be
turned to lock the Door (1) in place.
Latch (2)
Figure
D
5.
Check that Door (1) is properly closed and locked
after placing a pet inside the Kennel Crate.
Page 3
For technical questions, please call 1-800-444-3353.
Item 96341
Specifications
Dimensions
24-1/4″ L x 18-13/32″ W x 20-7/8″ H (assembled)
24-1/4″ L x 18-13/32″ W x 3-1/2″ H (folded)
Maintenance
1.
Keep all parts clean and dry.
The Kennel Crate can be hosed off to clean.
2.
Periodically check to see that all hardware is in place.
Parts List and Diagram
Part
Description
Qty
1
Front Door
1
2
Latch
2
3
Front Door Frame
1
4
Side Door Frame
1
5
Bottom Panel
1
6
Hook Latch
1
Part
Description
Qty
7
Side Door
1
8
Tray
1
9
Back Panel
1
10
Side Panel
1
11
Handle
2
12
Top Panel
1
Record Serial Number Here:
Note:
If product has no serial number, record
If product has no serial number, record
month and year of purchase instead.
Note:
Some parts are listed and shown for
Some parts are listed and shown for
illustration purposes only, and are not available
individually as replacement parts.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS DOCUMENT AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS
THERETO.
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

Navigation menu