Harbor Freight Motorcycle Wheel Balancing Stand Product Manual

: Harbor-Freight Harbor-Freight-Motorcycle-Wheel-Balancing-Stand-Product-Manual-723598 harbor-freight-motorcycle-wheel-balancing-stand-product-manual-723598 harbor-freight pdf

Open the PDF directly: View PDF .
Page Count: 4

Motorcycle Wheel Balancing Stand

Item 98488

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

When unpacking, make sure that the product is intact and undamaged.

If any parts are missing or broken, please call 1-800-444-3353 as soon as possible.

Visit our website at: http://www.harborfreight.com

Copyright© 2008 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape

or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing

improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included.

Manual Revised 11e

Shown in use with Wheel and

Tire (both not included).

SKU 98488 For technical questions, please call 1-800-444-3353. Page 2

Specications

Dual purpose stand to balance mounted tires.

Accepts up to 13-7/8” W tires, 12-1/2” wide

hubs and 1.59”/15 mm to 1.46”/37 mm axles.

The following Adapters (not included) are

available from Harbor Freight Tools:

SKU 98489

Balance Adapter to

be used for Ducati

® Motorcycles

SKU 98490

Balance Adapter to

be used for BMW®

Motorcycles

SKU 98493

Balance Adapter to

be used for Harley

Davidson® Motorcycles

SKU 65079

Balancer adapter to

be used for Honda®

motorcycles.

SKU 623 1” Travel Machinist’s

Dial Indicator

SKU 33675 1’’ Dial Indicator

SKU 5645 Multipositional

Magnetic Base with

Fine Adjustment

IMPORTANT SAFETY

INFORMATION

Assembly Precautions

1. Assemble only according

to these instructions.

Improper assembly can create hazards.

2. Wear ANSI-approved safety goggles and

heavy-duty work gloves during assembly.

3. Keep assembly area clean and well lit.

4. Keep bystanders out of the

area during assembly.

5. Do not assemble when tired or when under

the inuence of drugs or medication.

Use Precautions

1. This product is not a toy. Do not allow

children to play with or near this item.

2. Use for intended purpose only.

3. Inspect before use; do not use if

parts are loose or damaged.

4. Maintain product labels and nameplates.

These carry important safety information.

If unreadable or missing, contact

Harbor Freight Tools for a replacement.

Assembly Instructions

Read the ENTIRE IMPORTANT

SAFETY INFORMATION section at the

beginning of this document including

all text under subheadings therein

before set up or use of this product.

Assembly

1.

Side

Frame (2)

Socket Head Screw (9)

Figure 1

Attach each Side Frame (2) to the Base (1):

With the face of the Side Frame (2) facing

inward, insert two Socket Head Screw

(9) down through the Side Frame and

through the Base (1). Secure in place

with two Lock Nuts (10)-see Figure 1.

Below are accessories needed for wheel aligning.

(All not included)

REV 08f

SKU 98488 For technical questions, please call 1-800-444-3353. Page 3

2.

Axle (5)

Roller (6)

Figure 2

Set the Axle (5) onto the Rollers (6)

as shown in Figure 2.

Operating Instructions

1. Prior to use check to make

certain that the Axle is straight,

without any bends or damage.

2. Back off both Socket Set Screw (12) and

slide off one of the Centering Cones (4) from

Axle (5). Support the wheel of the motorcycle

in an upright position and slide the Axle (5)

through the wheel hub and replace the

Cone. Center the wheel on the Axle and

slide both Cones securely against the hub.

Tighten the Socket Cap Screws (12).

3. Lift the wheel and position the Axle over

the Rollers (6). Gently spin the wheel. The

heavier side would roll to the bottom. With

a chalk mark the tire at the upper most

location (across from the heavy side).

4. Lift the wheel assembly from the

stand and place on the oor. Attach a

balancing weight (not supplied) to the

inner edge of the rim and reposition the

wheel assembly over the Rollers (6).

NOTE: Use lightest possible weights.

With try and error, you should be able to

establish approximate required weights.

5. Gently spin the tire. Repeat steps 3 and 4

placing balancing weights on

alternative sides of the tire rim.

6. Continue to counter balance the wheel until

it spins evenly and does not repeatedly

stop at any specic point of its rotation.

7. Once the wheel is balanced, remove the

assembly and place on the oor, back off

one Socket Set Screw (12) and remove

the Centering Cone (4). Remove the Axle,

replace the Cone and tighten the screw.

Place the axle on the rollers.

Maintenance

1. Before each use, inspect the general

condition of the Balancing Stand.

Check for loose screws, misalignment

or binding of moving parts, cracked or

broken parts, and any other condition

that may affect its safe operation.

2. Periodically lubricate contact points

and Rollers with grease.

Replacing Rollers

1. Rollers (6) and Bearings (7) can be replaced

by removing Socket Head Screw (11) and

pulling Rollers off of the Balancing Stand.

2. Replace with new Rollers (6) and

Bearings (7) and secure with Socket

Set Screw (11). See Figure 2.

3. When not in use, store in a safe

location away from children.

PLEASE READ THE

FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR

HAS PROVIDED THE PARTS LIST AND

ASSEMBLY DIAGRAM IN THIS DOCUMENT AS

A REFERENCE TOOL ONLY. NEITHER THE

MANUFACTURER OR DISTRIBUTOR MAKES

ANY REPRESENTATION OR WARRANTY OF

ANY KIND TO THE BUYER THAT HE OR SHE

IS QUALIFIED TO MAKE ANY REPAIRS TO THE

PRODUCT, OR THAT HE OR SHE IS QUALIFIED

TO REPLACE ANY PARTS OF THE PRODUCT.

IN FACT, THE MANUFACTURER AND/OR

DISTRIBUTOR EXPRESSLY STATES THAT

ALL REPAIRS AND PARTS REPLACEMENTS

SHOULD BE UNDERTAKEN BY CERTIFIED

AND LICENSED TECHNICIANS, AND NOT

BY THE BUYER. THE BUYER ASSUMES ALL

RISK AND LIABILITY ARISING OUT OF HIS OR

HER REPAIRS TO THE ORIGINAL PRODUCT

OR REPLACEMENT PARTS THERETO, OR

ARISING OUT OF HIS OR HER INSTALLATION

OF REPLACEMENT PARTS THERETO.

SKU 98488 For technical questions, please call 1-800-444-3353. Page 4

Parts List and Assembly Diagram

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to

assure that its products meet high quality and

durability standards, and warrants to the original

purchaser that this product is free from defects in

materials and workmanship for the period of 90

days from the date of purchase. This warranty does

not apply to damage due directly or indirectly, to

misuse, abuse, negligence or accidents, repairs or

alterations outside our facilities, criminal activity,

improper installation, normal wear and tear, or

to lack of maintenance. We shall in no event be

liable for death, injuries to persons or property, or

for incidental, contingent, special or consequential

damages arising from the use of our product.

Some states do not allow the exclusion or limitation

of incidental or consequential damages, so the

above limitation of exclusion may not apply to

you. THIS WARRANTY IS EXPRESSLY IN LIEU

OF ALL OTHER WARRANTIES, EXPRESS

OR IMPLIED, INCLUDING THE WARRANTIES

OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product

or part must be returned to us with transportation

charges prepaid. Proof of purchase date and an

explanation of the complaint must accompany the

merchandise. If our inspection veries the defect,

we will either repair or replace the product at our

election or we may elect to refund the purchase

price if we cannot readily and quickly provide

you with a replacement. We will return repaired

products at our expense, but if we determine

there is no defect, or that the defect resulted from

causes not within the scope of our warranty, then

you must bear the cost of returning the product.

This warranty gives you specic legal

rights and you may also have other

rights which vary from state to state.

3491 Mission Oaks Blvd. • PO Box 6009

Camarillo, CA 93011 • (800) 444-3353

Part Description Qty.

1 Base 1

2 Side Frame 2

3 Mounting Plate 2

4 Centering Cone 2

5 Axle 1

6 Roller 4

7 Bearing 4

8 Sleeve 4

9 Socket Head Screw M8 x 20 4

10 Lock Nut M8 4

11 Socket Set Screw M8 x 25 4

12 Socket Head Screw M6 x 15 2

Note: Some parts are listed and

shown for illustration purposes only,

and are not available individually

as replacement parts.