Harbor Freight Non Contact Infrared Thermometer With Laser Targeting Product Manual

: Harbor-Freight Harbor-Freight-Non-Contact-Infrared-Thermometer-With-Laser-Targeting-Product-Manual-723512 harbor-freight-non-contact-infrared-thermometer-with-laser-targeting-product-manual-723512 harbor-freight pdf

Open the PDF directly: View PDF .
Page Count: 8

Download
Open PDF In Browser	View PDF

WARNING SYMBOLS AND DEFINITIONS
This is the safety alert symbol. It is used to alert you to
potential personal injury hazards. Obey all safety messages
that follow this symbol to avoid possible injury or death.
SAFETY

Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Addresses practices not related to personal injury.

SETUP
OPERATION
MAINTENANCE
Page 2

For technical questions, please call 1-888-866-5797.

Item 61894

Read all safety warnings and instructions. Failure to follow
the warnings and instructions may result in serious injury.

3. Avoid direct Eye exposure.
4. Do not expose the tool to
rain or wet conditions.
5. Stay alert, watch what you are doing and
use common sense when operating the
tool. Do not use while you are tired or
under the influence of drugs, alcohol
or medication. A moment of inattention
may result in serious personal injury.

10. Have your tool serviced by a qualified
repair person using only identical
replacement parts. This will ensure that
the safety of the tool is maintained.
11. Position batteries in proper polarity and
do not install batteries of different types,
charge levels, or capacities together.

6. Do not use the tool if the Trigger does
not turn it on and off. Any tool that cannot
be controlled with the Trigger is
dangerous and must be repaired.

12. Maintain labels and nameplates on the tool.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.

7. Disconnect the battery before making
any adjustments, changing accessories,
or storing the tool. Such preventive
safety measures reduce the risk of
activating the Laser accidentally.

13. This product is not a toy.
Keep it out of reach of children.

8. Maintain the tool. Check for misalignment
or binding of parts, breakage of parts and
any other condition that may affect the
tool’s operation. If damaged, have the
tool repaired before use. Many accidents
are caused by poorly maintained tools.

14. The warnings, precautions, and instructions
discussed in this instruction manual cannot
cover all possible conditions and situations
that may occur. It must be understood by
the operator that common sense and caution
are factors which cannot be built into this
product, but must be supplied by the operator.
15. People with pacemakers should
consult their physician(s) before use.
Electromagnetic fields in close proximity to
heart pacemaker could cause pacemaker
interference or pacemaker failure.

For technical questions, please call 1-888-866-5797.

MAINTENANCE

SAVE THESE INSTRUCTIONS.

Item 61894

SETUP

2. Do not open the housing other
than battery compartment.

9. Use the tool in accordance with these
instructions, taking into account the
working conditions and the work
to be performed. Use of the tool for
operations different from those intended
could result in a hazardous situation.

OPERATION

1. Do not use for medical purposes.

SAFETY

IMPORTANT SAFETY INFORMATION

Page 3

Specifications

SAFETY

Measurement
Range

-36.4ºF to 968ºF
(-38ºC to 520ºC)

Accuracy

± 2% above 32ºF
± 4.5% below 31ºF

Response Time

1 Sec

Spot Size Ratio

8:1 (Distance : Spot size)

Needed Batteries 2 AAA (not included)

LASER LIGHT

AVOID DIRECT EYE EXPOSURE

Max Output: < 1 mW,
Wavelength: 650 nm

CLASS II LASER PRODUCT

This product complies with 21 CFR
1040.10 and 1040.11 - Diode Mfr.: # 44,
Ge Xin Road, Z hen Shi New Industrial
Z one, Z hang Mu Tou Town, Dong Guan
City, Guang Dong Province, China

WARNING

To prevent serious injury:
do not use for medical purposes.
Serial:

14b

Setup - Before Use:
SETUP

Read the ENTIRE IMPORTANT SAFETY INFORMATION section
at the beginning of this manual including all text under
subheadings therein before set up or use of this product.

Installing the Battery
Remove the battery cover and insert two AAA batteries into the unit,
following indicated polarity. Replace the battery cover.

Functions
OPERATION

Laser Beam
LCD
ºF/ºC Button

ON/OFF
Trigger

MAINTENANCE

Battery
Cover

Page 4

For technical questions, please call 1-888-866-5797.

Item 61894

Operating Instructions

SAFETY

Read the ENTIRE IMPORTANT SAFETY INFORMATION section
at the beginning of this manual including all text under
subheadings therein before set up or use of this product.

General Operating Instructions

2. Push the ºF/ºC button to toggle between
Fahrenheit to Celsius, and to recover
the last reading when in OFF mode.
3. Squeeze the Trigger and move the
laser to see a constant temperature
reading and max reading.
4. Release the Trigger to display the
most recent temperature reading, or to
allow 15 seconds for auto shut off.

2" diameter at
16" distance

3" diameter at
24" distance

Distance to Spot Size = 8:1
Field of View

7. When finished, release the Trigger.
The last temperature will display for 15
seconds, then the unit will shut off.
8. Clean the lens with dry compressed air
and wipe the rest of the unit down with a
soft, damp cloth, then store the product
indoors out of children’s reach.
9. To prevent accidents, turn off the
tool and disconnect its power supply
after use. Clean, then store the tool
indoors out of children’s reach.

MAINTENANCE

5. Non-reflective surfaces will yield a more
accurate reading than reflective surfaces.
Duct tape (sold separately) can be applied
to reflective surfaces in order to get a better
measurement. Allow sufficient time for the
tape to match the temperature of the surface
it is applied to before trying to get a reading.

1" diameter at
8" distance

SETUP

1. Squeeze the Trigger to activate the
Laser and temperature reading.

Distance

OPERATION

Note: When moving the Thermometer to an area
with significantly different ambient temperature,
allow the unit to adjust to the new ambient
temperature for 30 minutes before use.

6. The object being tested should be
larger than the size calculated by the
Field of View diagram, below.

Spot Center

Note: Do not expose this product to strong
electromagnetic fields, such as those generated
by an arc welder, induction heater, etc.

Item 61894

For technical questions, please call 1-888-866-5797.

Page 5

Maintenance and Servicing

SAFETY

Procedures not specifically explained in this manual must
be performed only by a qualified technician.

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Release the Trigger and remove the batteries from the Laser Thermometer
before performing any inspection, maintenance, or cleaning procedures.
TO PREVENT SERIOUS INJURY FROM TOOL FAILURE:
Do not use damaged equipment. If damage is noted, have
the problem corrected before further use.

Cleaning, Maintenance, and Lubrication
SETUP

1. BEFORE EACH USE, inspect the general
condition of the tool. Check for:
•

2. AFTER USE, wipe external surfaces
of the tool with clean cloth.

loose hardware,
•

misalignment or binding of parts,
•

cracked or broken parts,
•

damaged electrical wiring, and
•

any other condition that may
affect its safe operation.

OPERATION
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.

PLEASE READ THE FOLLOWING CAREFULLY
MAINTENANCE

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER
OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE
BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR
THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE
MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS
REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS,
AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF
HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO,
OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Page 6

For technical questions, please call 1-888-866-5797.

Item 61894

Parts List and Diagram
Description

Front Cover
Trigger
Battery Cover
Front Mass
RMASS (Aluminium Alloy)
Laser Holder-B

Qty
1
1
1
1
1
1

Part
7
8
9
10
11
12

Description

TPI RMASS
PCB
LCD
LCD
Rear Cover
Switch Button

Qty
1
1
1
1
1
1

MAINTENANCE

OPERATION

SETUP

1
2
3
4
5
6

SAFETY

Part

Item 61894

For technical questions, please call 1-888-866-5797.

Page 7

Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality
and durability standards, and warrants to the original purchaser that this product is free from
defects in materials and workmanship for the period of 90 days from the date of purchase. This
warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or
accidents, repairs or alterations outside our facilities, criminal activity, improper installation,
normal wear and tear, or to lack of maintenance. We shall in no event be liable for death,
injuries to persons or property, or for incidental, contingent, special or consequential damages
arising from the use of our product. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation of exclusion may not apply to
you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the complaint
must accompany the merchandise. If our inspection verifies the defect, we will either repair or
replace the product at our election or we may elect to refund the purchase price if we cannot
readily and quickly provide you with a replacement. We will return repaired products at our
expense, but if we determine there is no defect, or that the defect resulted from causes not
within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also
have other rights which vary from state to state.

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Create Date                     : 2014:02:11 11:52:46-08:00
Creator                         : Adobe InDesign CC (Macintosh)
Modify Date                     : 2014:02:11 11:53:46-08:00
Has XFA                         : No
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Instance ID                     : uuid:996aba09-35a3-0147-bc13-8657d5dbd4ee
Original Document ID            : adobe:docid:indd:2947f79c-bab0-11df-a4dc-d1b6dbadcc65
Document ID                     : xmp.id:8579e585-1a4a-4e6e-80cb-9da56e3a824b
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:ee679ff9-9bd2-42bd-9bd0-98f7fa0dc91a
Derived From Document ID        : xmp.did:e7adf3e0-122b-42a4-89b3-6e5ff327834b
Derived From Original Document ID: adobe:docid:indd:2947f79c-bab0-11df-a4dc-d1b6dbadcc65
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC (Macintosh)
History Changed                 : /
History When                    : 2014:02:11 11:52:46-08:00
Metadata Date                   : 2014:02:11 11:53:46-08:00
Creator Tool                    : Adobe InDesign CC (Macintosh)
Format                          : application/pdf
Producer                        : Adobe PDF Library 11.0
Trapped                         : False
Page Count                      : 8

EXIF Metadata provided by EXIF.tools