Harbor Freight Solar Decorative Led Lights 3 Pc Product Manual

Harbor-Freight-60561-Owner-S-Manual harbor-freight-60561-owner-s-manual

Manual for the 60561 Solar Decorative LED Lights - 3 Piece 60561 Solar Garden Light Set - Dragonfly, Hummingbird & Butterfly

: Harbor-Freight Harbor-Freight-Solar-Decorative-Led-Lights -3-Pc-Product-Manual-724203 harbor-freight-solar-decorative-led-lights---3-pc-product-manual-724203 harbor-freight pdf

Open the PDF directly: View PDF .
Page Count: 8

Page 2 For technical questions, please call 1-800-444-3353. Item 60561

Specifications

Battery Type AA NiCd rechargeable

Battery Rating 300mAh

Running time when

fully charged 8 hours

Important Safety Information

1. Assemble only according to these

instructions. Improper assembly

can create hazards.

2. Wear ANSI-approved safety goggles

during assembly.

3. Keep assembly area clean and well lit.

4. Keep bystanders out of the

area during assembly.

5. Do not assemble when tired

or when under the influence

of drugs or medication.

6. Position battery in proper polarity and

do not install batteries of different types,

charge levels, or capacities together.

7. WARNING: The brass components of

this product contain lead, a chemical

known to the State of California

to cause birth defects (or other

reproductive harm). (California Health

& Safety code § 25249.5, et seq.)

8. This product is not a toy. Do not allow

children to play with or near this item.

9. Use as intended only.

10. Inspect before every use; do not use

if parts are loose or damaged.

11. Maintain product labels and

nameplates. These carry

important safety information.

If unreadable or missing, contact

Harbor Freight Tools for a replacement.

Page 3For technical questions, please call 1-800-444-3353.Item 60561

Assembly Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the

beginning of this document including all text under subheadings therein

before set up or use of this product.

Note: For additional information regarding the parts listed in the following

pages, refer to the Assembly Diagram near the end of this manual.

Assembly

1. Unthread the two screws on the battery cover and remove the battery cover.

2. Insert the AA battery into the battery housing paying attention to the polarity.

3. Replace the Battery cover and secure with the screws.

4. Set one of the Decorative LED Shapes (2) onto the Top Tube (3). Slide the Top

Tube (3), into the Bottom Tube (4). Slide the Stake (5) onto the Bottom Tube (4).

5. Repeat steps 1 - 3 for the other two light sets.

Functions

Decorative LED Shape (2)

Top Tube (3)

Bottom Tube (4)

Stake (5)

Solar Panel (1)

Battery Cover (9)

(On back of Solar Panel)

Power Switch (7)

(On back of Solar Panel)

Figure A

Page 4 For technical questions, please call 1-800-444-3353. Item 60561

Operating Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the

beginning of this manual including all text under subheadings therein

before set up or use of this product.

Tool Set Up

1. Decide where you want to place the Solar Light Set. Choose a

location that receives full, direct sunlight a minimum of six hours a day.

The location should not be near nighttime light sources such as porch lights

or streetlights as this will cause the Solar Light Set to remain off.

Note: During the day, the Solar Panel converts sunlight into electricity, recharging the

battery. The amount of light the Solar Panel receives depends on placement of the

Solar Light, geographic location and weather. If the weather is cloudy and the panel

did not receive a full charge, the Solar Garden Light may not achieve the full hours

of operating time. It will catch up on its own after two to three days of full sun.

2. Make certain that the path of the Stake (5) is clear of lines, cables and conduits.

3. Push the Stake (5) directly into the ground.

Charging

1. The Solar Light Set will need to charge for at least twelve

hours before using it for the first time.

2. Set the Power Switch to “Auto”.

3. Allow to charge for two sunny days before use.

General Operating Instructions

1. Move the Power Switch to “Auto” to activate the Solar Light.

2. The Light will automatically turn ON during the night. After the initial charge

is set, check to see that the Light (2) is on by viewing the light at night or in a

dark location. If the Light (2) is not lit, check the position of the Power Switch

and check that the Solar Panel has had full sunlight for 6 to 12 hours.

Page 5For technical questions, please call 1-800-444-3353.Item 60561

Maintenance

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the

beginning of this document including all text under subheadings therein

before set up or use of this product.

TO PREVENT SERIOUS INJURY FROM TOOL FAILURE:

Do not use damaged equipment. If abnormal noise or vibration

occurs, have the problem corrected before further use.

1. Clean regularly with a damp towel. Do

not use any type of solvent for cleaning.

Do not put too much pressure on the

Light, Solar Panel or accessories

while cleaning. Dry thoroughly.

2. WARNING! Make sure the Power

Switch is in its “Off” position

before performing any inspection,

maintenance, or cleaning procedures.

3. BEFORE EACH USE, inspect the

general condition of the tool. Check for:

• leaking, swollen, or cracked battery,

• loose hardware,

• misalignment or binding of parts,

• cracked or broken parts, and

• any other condition that may

affect its safe operation.

4. AFTER USE, wipe external surfaces

of the tool with clean cloth.

5. Replace the battery every 12 months.

a. Unscrew the screws holding

the Battery Cover (9) in place

and remove the Battery Cover

from the Solar Panel (1).

b. Remove the old battery.

c. NiCd BATTERY MUST BE

RECYCLED OR DISPOSED OF

PROPERLY.

Do not short, incinerate

or open battery.

d. Install a new NiCd AA, 300mAh

battery into the Battery

Compartment. Check that the

battery is placed according

to the correct polarity.

e. Replace the cover and secure

in place with the Screws.

Troubleshooting

Problem Possible Causes Probable Solutions

Light will

not turn on

1. Power Switch (7) not set to “Auto”.

2. Battery not allowed time for recharging

via Solar Panel.

3. Solar Light is set near nighttime

light sources such as porch

lights or street lights.

4. Solar Panel is dirty and

covered with dirt or dust.

1. Check position of Power Switch.

2. Check that Solar Panel has direct

access to sunlight. Allow one

to two days for a full charge.

3. Move Solar Light or change

Solar Panel position.

4. Clean Solar Panel with a soft cloth.

Page 6 For technical questions, please call 1-800-444-3353. Item 60561

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY

DIAGRAM IN THIS DOCUMENT AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER

OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE

BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR

THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE

MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS

REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS,

AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF

HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO,

OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Page 7For technical questions, please call 1-800-444-3353.Item 60561

1

3

4

5

Parts List and Diagram

Part Description Qty

1 Solar Panel 3

2 Decorative LED Shape 3

3Top Tube 3

4Bottom Tube 3

5 Stake 3

Part Description Qty

6 Battery 3

7 Power Switch 3

8 Screw 6

9 Battery Cover 3

Record Serial Number Here:

Note: If product has no serial number, record month and year of purchase instead.

Note: Some parts are listed and shown for illustration purposes only,

and are not available individually as replacement parts.

6

7

8

9

2

Page 8 For technical questions, please call 1-800-444-3353. Item 60561

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality

and durability standards, and warrants to the original purchaser that this product is free from

defects in materials and workmanship for the period of 90 days from the date of purchase.

This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence

or accidents, repairs or alterations outside our facilities, criminal activity, improper installation,

normal wear and tear, or to lack of maintenance. We shall in no event be liable for death,

injuries to persons or property, or for incidental, contingent, special or consequential damages

arising from the use of our product. Some states do not allow the exclusion or limitation of

incidental or consequential damages, so the above limitation of exclusion may not apply to you.

THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR

IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with transportation

charges prepaid. Proof of purchase date and an explanation of the complaint must accompany

the merchandise. If our inspection verifies the defect, we will either repair or replace

the product at our election or we may elect to refund the purchase price if we cannot readily

and quickly provide you with a replacement. We will return repaired products at our expense,

but if we determine there is no defect, or that the defect resulted from causes not within

the scope of our warranty, then you must bear the cost of returning the product.

This warranty gives you specific legal rights and you may also

have other rights which vary from state to state.

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353