Harbor Freight Steel Floor Jack Cross Beam Product Manual

Manual for the 60762 Steel Floor Jack Cross Beam 60762 Steel Floor Jack Cross Beam

68056 60762

: Harbor-Freight Harbor-Freight-Steel-Floor-Jack-Cross-Beam-Product-Manual-723701 harbor-freight-steel-floor-jack-cross-beam-product-manual-723701 harbor-freight pdf

Open the PDF directly: View PDF .
Page Count: 4

Page 2 For technical questions, please call 1-800-444-3353. Item 60762

Specifications

Rated Capacity 4,000 lb.

Compatibility Pittsburgh® item 68048, 68049, 68050,

68056, 60678, 60688, 60706, or 69227

Important Safety Information

Failure to heed these markings may result in personal injury and/or property damage:

1. Study, understand, and follow all

instructions before operating this device.

2. Do not exceed 4,000 lb. rated capacity.

3. Assure load is secured to the device.

4. To be used only with the following:

Pittsburgh® item 68048, 68049, 68050,

68056, 60678, 60688, 60706, or 69227.

5. Release load locking devices

(if employed) slowly and carefully.

6. No alterations shall be

made to this product.

7. Adjust pads to keep bar

level during lifting.

8. Only use with included safety

chains properly connected to

prevent overextension.

9. Install and use aligned perpendicular

to floor jack body only.

10. Also, study, understand, and

follow all floor jack instructions

before operating this device.

11. Wear ANSI-approved safety goggles

and heavy-duty work gloves during use.

12. Do not move or dolly the vehicle

while on the cross beam.

13. Use as intended only.

Do not use for lifting human weight.

Keep clear of raised load.

Do not use for aircraft purposes.

14. Lift vehicle only at

manufacturer-recommended locations.

15. Inspect before every use;

do not use if parts loose or damaged.

16. Lifting device only.

Immediately after lifting, support the

vehicle with appropriate means.

Assembly Instructions

1. Remove saddle mounting bolt

and saddle from Floor Jack.

2. Place Cross Beam on Floor Jack.

3. For 2 or 2.5 ton floor jacks,

slide Spacer onto Mounting Bolt

before installing it.

4. Install Cross Beam’s Mounting Bolt

and tighten it securely in place

while keeping Cross Beam aligned

perpendicular to Floor Jack body.

Page 3For technical questions, please call 1-800-444-3353.Item 60762

Operation Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the

beginning of this document including all text under subheadings therein

before set up or use of this product.

1. Lower both Saddle Pads completely.

2. Align each Saddle Pad

under a vehicle lifting point.

Center the vehicle’s weight

over the Floor Jack.

WARNING! Lift vehicle only at

manufacturer-recommended locations.

3. Use Floor Jack to raise Cross Beam

until one of the Saddle Pads is about to

contact one of the vehicle lifting points.

4. Turn the Saddle Pads to

adjust each one until they both

contact the lifting points.

5. Stay clear of vehicle, Jack and

Cross Beam while slowly raising the

vehicle until it is at the desired height.

WARNING! While lifting, make sure

that the Cross Beam remains level and

the load is centered over the Floor Jack.

6. Place two Jack Stands at

manufacturer-recommended support

points and adjust until they almost

contact each support point.

7. Stay clear while lowering the vehicle

onto the Jack Stands. Lower the

vehicle’s weight completely onto

Jack Stands before working under it.

Parts List and Diagram

Part Description Qty

1 Housing 1

2 Extension 2

3 Saddle 2

4 Saddle Pad 2

Part Description Qty

5 Bolt 8

6 Chain 2

7 Washer 2

8 Spring Washer 2

Part Description Qty

9 Chain Bolt 2

10 Mounting Bolt 1

11 Spacer* 1

*For 2 and 2.5 ton jack mounting.

10

11

1

2 3

4

5

678

9

Record Serial Number Here:

Note: If product has no serial number,

record month and year of purchase instead.

Note: Some parts are listed and shown for illustration purposes

only, and are not available individually as replacement parts.

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY

DIAGRAM IN THIS DOCUMENT AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER

OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE

BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR

THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE

MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS

REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS,

AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF

HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO,

OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality

and durability standards, and warrants to the original purchaser that this product is free from

defects in materials and workmanship for the period of 90 days from the date of purchase.

This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence

or accidents, repairs or alterations outside our facilities, criminal activity, improper installation,

normal wear and tear, or to lack of maintenance. We shall in no event be liable for death,

injuries to persons or property, or for incidental, contingent, special or consequential damages

arising from the use of our product. Some states do not allow the exclusion or limitation of

incidental or consequential damages, so the above limitation of exclusion may not apply to you.

THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR

IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with transportation

charges prepaid. Proof of purchase date and an explanation of the complaint must accompany

the merchandise. If our inspection verifies the defect, we will either repair or replace

the product at our election or we may elect to refund the purchase price if we cannot readily

and quickly provide you with a replacement. We will return repaired products at our expense,

but if we determine there is no defect, or that the defect resulted from causes not within

the scope of our warranty, then you must bear the cost of returning the product.

This warranty gives you specific legal rights and you may also

have other rights which vary from state to state.

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353