Harbor Freight Windmill Mole Chaser Product Manual 47987

: Harbor-Freight Harbor-Freight-Windmill-Mole-Chaser-Product-Manual-724142 harbor-freight-windmill-mole-chaser-product-manual-724142 harbor-freight pdf

Open the PDF directly: View PDF .
Page Count: 5

MOLE CHASER

WINDMILL

ASSEMBLY and OPERATING

INSTRUCTIONS

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our Web site at http://www.harborfreight.com

For technical questions and replacement parts, please call 1-800-444-3353

Model 47987

Copyright© 2002 by Harbor Freight Tools®. All rights reserved. No portion of this

manual or any artwork contained herein may be reproduced in any shape or form

without the express written consent of Harbor Freight Tools .

Page 2

SKU 47987

Specifications

Save This Manual

You will need the manual for the safety warnings and precautions, assembly instructions,

operating and maintenance procedures, parts list and diagram. Keep your invoice with this

manual. Write the invoice number on the inside of the front cover. Keep the manual and

invoice in a safe and dry place for future reference.

Safety Warnings and Precautions

WARNING: When using tools and this product, basic safety precautions should always

be followed to reduce the risk of personal injury and damage to equipment.

Read all instructions before using this tool!

1. Keep work area clean. Cluttered areas invite injuries.

2. Observe work area conditions. Keep work area well lighted.

3. Keep children away. Children must never be allowed in the work area. Do not let

them handle Windmill.

4. Use the right product for the job. There are certain applications for which this

Windmill was designed. Do not modify this Windmill and do not use this Windmill for

a purpose for which it was not intended .

5. Dress properly. Do not wear loose clothing or jewelry as they can be caught in

moving parts. Protective, electrically nonconductive clothes and nonskid footwear are

recommended when working. Wear restrictive hair covering to contain long hair.

6. Use eye protection. Always wear ANSI approved impact safety goggles during

assembly.

7. Do not overreach. Keep proper footing and balance at all times.

8. Maintain tools with care. Keep Windmill clean for better and safer performance.

Follow instructions for lubricating.

9. Stay alert. Watch what you are doing, use common sense. Do not assemble the

Windmill when you are tired.

10. Check for damaged parts. Before using Windmill, any part that appears damaged

should be carefully checked to determine that it will operate properly and perform its

intended function. Check for alignment and binding of moving parts; any broken parts

or mounting fixtures; and any other condition that may affect proper operation. Any

part that is damaged should be properly repaired or replaced by a qualified technician.

Overall Dimensions 19-1/2” L x 18-1/2” W

Blade Dimensions 18” L x 2-1/2” W

Weight 2.3 Lbs.

Page 3

SKU 47987

11. Replacement parts and accessories. When servicing, use only identical

replacement parts. Use of any other parts will void the warranty. Only use accessories

intended for use with this tool.

12. Do not assemble Windmill if under the influence of alcohol or drugs. Read

warning labels on prescriptions to determine if your judgment or reflexes are impaired

while taking drugs. If there is any doubt, do not assemble the tool.

13. Maintenance. For your safety, maintenance should be performed regularly by a

qualified technician.

14. Location. Choose a safe location away from power lines to install the Windmill.

Caution: If setting up the Windmill on a roof surface, extreme care must be taken

when working on a sloped, slippery roof surface; this type of work on a roof should

only be done by an experienced worker who is capable of handling the physical de-

mands of this type of job.

15. Extreme Weather Conditions. Be aware that the Windmill is not designed to withstand

extreme weather conditions; the product may break or fail under extreme weather conditions

resulting in property damage and/or personal injury. Locate the product in an area that is clear

of passing people or animal traffic.

Warning: The warnings, cautions, and instructions discussed in this instruction manual

cannot cover all possible conditions and situations that may occur. It must be under-

stood by the operator that common sense and caution are factors which cannot be

built into this product, but must be supplied by the operator.

Unpacking

When unpacking, check to make sure the parts listed on page 5 are included. If any parts

are missing or broken, please call Harbor Freight Tools at the number on the cover of this

manual as soon as possible.

Page 4

SKU 47987

Refer to FIGURE 1 below, and the Assembly Drawing on page 5.

Warning!! Before setting this Windmill in the ground, contact your local utility company to

make sure there are no buried cables or pipes in the desired location. If locating the Windmill

on a rooftop, read and adhere to the warnings on page 3.

1. Stack the Blades (3) so that they resemble the pattern in the box in FIGURE 1, making

sure the fins face out, toward the wind. Lay number 2 over number 1 so that the holes

match. Then, lay number 3 over number 2 so that all four holes match evenly.

2. Lubricate the Bearing Assembly (4) prior to assembly, using a lightweight grease.

3. Using three Bolts (8) and three star Washers (10), attach the blade assembly to the

Bearing Assembly (4) and secure with three Nuts (6).

4. Attach the Directional Finder (2) to the Tube Frame (1) with two Self-tapping Screws

(5). Thread in the Bolt (9) to secure the Bearing Assembly (4). See Figure 1.

5. Tap Extension Tube (B) into the ground. Make sure it is securely in place and insert

Extension Tube (A) onto Tube (B).

Operation Notes:

1. A rattling sound in the tube is normal.

2. Just a few turns in a 24 hour period will effectively rid the area of moles.

3. Keep the unit lubricated. See Maintenance section below.

Assembly and Operation

Maintenance

1. The Bearing Assembly (4) is not grease-packed, it will require lubricating periodically.

2. Check the pole stability periodically. If it seems loose, remove the Windmill and pound in

the pole. Replace the Windmill.

3. Keep the Blades (3) clean of dirt and debris.

REV 11/04, 01/07, 02/07

123

Stacked blade assembly.

Close-up of matched

holes after all 3

blades are stacked.

Directional

Finder (2)

Self-tapping Screws (5)

Blades (3)

Bolts/Star washers

(8)/(10) Bearing (4)Tube Frame (1)

Nuts (6)

FIGURE 1

Bolts (9)

Extension

Tube (A)

Page 5

SKU 47987

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS

MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBU-

TOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE

OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS

QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER

AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS

SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE

BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER

REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING

OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

NOTE: Some parts are listed and shown for illustration purposes only and are not available indi-

vidually as replacement parts.

REV 01/07; 02/07

Parts List and Assembly Drawing

Part No. Description Qty

1 Tube Frame 1

2 Direction Finder 1

3 Blade 3

4 Bearing Assembling 1

5 Self-tapping screw 3

6 Nut 3

7 Washer 1

8 Bolt 3

9 Bolt 1

10 Star-washer 3

A Extension Tube 1

B Extension Tube 1

y