Harmar Mobility Al001 Users Manual

AL001 to the manual e023b649-08fd-4a04-8936-5c655b04ea9d

2015-02-09

: Harmar-Mobility Harmar-Mobility-Al001-Users-Manual-563996 harmar-mobility-al001-users-manual-563996 harmar-mobility pdf

Open the PDF directly: View PDF PDF.
Page Count: 10

DownloadHarmar-Mobility Harmar-Mobility-Al001-Users-Manual- Harmar-mobility-al001-users-manual
Open PDF In BrowserView PDF
AL001

your

AL001 Users Manual
Harmar Mobility
Rev.1 June 2008

Please read the manual before using.

WARNING!
A
warning
indicates
a
potentially
dangerous
situation,
which
if
not
avoided,
could
result
in
death
or
serious
injury.
1. Read all instructions and save them for future
reference.
2. Follow all warnings and instructions marked on the
product.
3. Do not ride any vehicle while loading onto the carrier.
4. Do not stand on the carrier.
5. Never exceed vehicle tongue weight ratings.
6. Always store the carrier in a safe place.
7. Only use the carrier with Class 2, 3 or larger hitch.
8. Improper use, storage or installation of carrier could
result in death or serious injury.

9. Do not put the product on any kinds of trailers.
10. Carrying capacity is limited to 500 lbs. max.
Assembly Instructions
Tools Need:
 5/8” wrench
 1/2” wrench
 3/4” wrench
 9/16” wrench
 Phillips screwdriver
Step.1
Insert the hitch into the carrier rack. See the figure

Step.2
Insert four 3/8”x7/8” bolts on the bottom of your carrier tube.
Tighten bolts firm with a wrench. See the figure.

Step.3
Screw spring pull pin into carrier. Add reflectors. See the figure.

Step.4
Screw spring pull pin into jam nut. Screw spring pull pin into ramp
bracket. Bolt bracket to frame. Secure with nuts and lock washers.
See the figure.
NOTE! To prevent loosening of the spring pull pin, torque the jam
nut tightly against the ramp bracket.

When in use:
Use safety pin to adjust the hitch. See the figure.

Insert the spring pull pin into the hole on the ramp when you stand
the ramp. See the figure.

ATTENTION!
For the first installation of the anti-tilt lock bracket insert the
carrier into the hitch receiver. Do not insert the hitch pin at this
point. Now slide the carrier toward the vehicle until it holds the antitilt lock bracket while an additional person holds the carrier
securely against the hitch receiver.

BE SURE TO TORQUE THE BOLTS TO 35-40FT
LBS.

Next loosen the bolts on the anti-tilt lock bracket. (There
should be grooves where the bolts were tightened against the hitch
receiver)
This procedure is required only during the initial installation of
the anti-tilt lock bracket as for the grooves will ensure repeated
relocating of the anti-tilt lock bracket. Now pull the carrier out to its
final location and install the hitch pin. Return the anti-tilt lock
bracket to the location securely against the hitch receiver and
torque the bolts.

THE BOLTS SHOULD FALL INTO THE
GROOVES CREATED EARLIER IN THIS
PROCEDURE.

ATTENTION:
Large chain loops on trailer hitches will not accept the anti-tilt
locking device. In this case you will be unable to use the
supplied anti-tilt locking devise.

Assembly

Index
1

Parts List
Description
ramp

Quantity
1

2
3
4
5

ramp bolt sets
Carriage bolt sets
Ramp bracket
Spring pull pin

2
2
1
2

6
7
8
9
10
11
12
13

reflector
carrier tray
gear
hitch pin
M12x70 bolt
adjust bolt
M10x30 bolt
anti tilt lock bracket

2
1
1
1
1
1
3
1

14

lock bolt

4

YOU MUST HAND WASH
OR USE A TOUCHLESS
AUTOMATIC CAR WASH
TO PREVENT LIFT DAMAGE.

IF YOU HAVE ANY QUESTIONS REGARDING
WASHING A CAR EQUIPPED WITH A HARMAR
LIFT PLEASE CALL THE HARMAR TECHNINCAL
SERVICES DEPARTMENT
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:08:23
Modify Date                     : 2009:03:30 11:27:48-04:00
Create Date                     : 2009:03:30 11:27:48-04:00
Metadata Date                   : 2009:03:30 11:27:48-04:00
Creator Tool                    : Adobe Acrobat 8.0 Combine Files
Format                          : application/pdf
Document ID                     : uuid:60b96677-7736-8840-9a2b-f170214a1f0c
Instance ID                     : uuid:6e87f179-a1fe-274b-ba47-42101ce8cec8
Producer                        : Adobe Acrobat 8.0
Page Count                      : 10
Creator                         : Adobe Acrobat 8.0 Combine Files
EXIF Metadata provided by EXIF.tools

Navigation menu