Havis Shields Dome Light Kr Dl Users Manual INST 9 05

KR-DL to the manual 39065087-86f0-4a81-aa66-e73a845f0b2b

: Havis-Shields Havis-Shields-Dome-Light-Kr-Dl-Users-Manual-564404 havis-shields-dome-light-kr-dl-users-manual-564404 havis-shields pdf

Open the PDF directly: View PDF .
Page Count: 2

Download
Open PDF In Browser	View PDF

Dome Light KR-DL
Installation Instructions
Warning: Please read all instructions and warnings prior to installation of the Dome Light.
TOOLS REQUIRED:
Phillips Screw Driver

Wire Cutter

HARDWARE: (Supplied in Kit)
Qty.
2
2

Description
#8-32 Machine Screw
#8 KEP Nut

Qty.
2
2

Description
#8 Fender Washer
#8 Sheet Metal Screw

INSTALLATION:
1. Mounting:
•

A drill template is provided on the back of this instruction sheet. Detach the
template, position it on the desired location for installation, and mark drill locations.
Caution: Before drilling holes, ensure that the mounting surfaces are clear and that the
screws will not damage the internal parts of the vehicle.
Caution: Ensure that the Dome Light is installed in areas recommended by the vehicle
manufacturer.

•
•
•

Drill the mounting holes.
Connect the power leads using wire splices.
Remove the template prior to installing the fixture. Secure the base of the fixture in
position using the supplied machine screws, washers, and nuts.
Caution: Thread forming screws are supplied for alternate installations. If the fixture needs to
be mounted with thread forming screws, please note that it may not always be sufficiently
secured. It is at the sole discretion of the installer to determine the suitability of using threadforming screws for a particular installation.

•
•

The fixture is supplied with two clear lenses and two red lenses. Install two lenses
suitable for the vehicle.
Test the fixture for proper operation.

Caution: The Dome Light uses bulbs which can be VERY HOT! Do not touch a bare bulb
when it is lighted.
2. Operation:
•
•

The fixture has two switches, which control each of the two lamps independently.
Pressing each switch once turns the lamp on, and pressing it a second time turns the
lamp off.

3. Troubleshooting:
•
•
•
•

In the event of improper operation, first check that the switches are turned on.
Second, check the each bulb and replace if burned out.
Third, check the fuse (if installed) and replace if necessary.
Finally, use a voltmeter to ensure that the fixture is receiving adequate power. The
light requires nominally 12 VDC for correct operation. Voltage must be measured
using the fixture power leads, not the vehicle chassis. Correct any faults found.

REPLACEMENT PARTS:
Part #
KRM89073-17

Description
Automotive Type 918 Replacement Lamp, 7 Watt, 12 VDC

Clip Here

Clip Here

∅0.17 (11/64” Drill)
Mounting Holes

TEMPLATE:
Wireway

5-5/16”
KR-DL-INST-9-05



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Create Date                     : 2006:01:11 16:06:52-05:00
Modify Date                     : 2006:01:11 16:06:52-05:00
Page Count                      : 2
Creation Date                   : 2006:01:11 21:06:52Z
Mod Date                        : 2006:01:11 21:06:52Z
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Author                          : moleary
Metadata Date                   : 2006:01:11 21:06:52Z
Creator                         : moleary
Title                           : Microsoft Word - KR-DL-INST-9-05.doc

EXIF Metadata provided by EXIF.tools