Hayter Mowers 13 30 Users Manual F 050732L

!! Hayter-4 Hayter Lawn Mower Manuals - Lawn Mower Manuals – The Best Lawn Mower Manuals Collection

1330 to the manual 90f24996-1e53-4aa6-9bbe-f351d43e2a7e

2015-02-09

: Hayter-Mowers Hayter-Mowers-13-30-Users-Manual-564489 hayter-mowers-13-30-users-manual-564489 hayter-mowers pdf

Open the PDF directly: View PDF .
Page Count: 40

F-050732L

13/30

HERITAGE TRACTOR

CODE131C

INSTRUCTION BOOK

FROM SERIAL NO:131C001001 MANUAL PART NO: 131010(REV.0.)

F-050732L

4 (17x195)

7 (17x192)

5 (30x49)

4 (17x47)

5 (1001054)

6 (17x146)

4 (25x3)

6 (2x82)

7 (14x79)

6 (1x121)

7 (15x116)

F-050732L

11 8

14 9

F-050732L

115

17 18

F-050732L

226

F-050732L

12 3 4567

MAX 90N

+MAX 150N

11 12

13 14

1234567

10 11 12 13 14 15

1001054

2x82 14x79

17x47

20729

17x195

17x192

25x3

17x146

1x121

15x116 30x49

F-050732L

LIMITED WARRANTY

Hayter Limited warrants to the original user / purchaser that this unit shall be free from defects in material and

workmanship under normal use and service for a period of three years from the date of purchase. The manufac-

turers of the engine and battery pack system (where applicable) furnish their own warranty and services are pro-

vided through their authorised network (Refer to “Engine/Battery Pack Warranty Statement”). To qualify for the

full benefit of the warranty, the warranty registration card must be returned within 60 days of purchase. Subject to

the conditions and exclusions noted in this limited warranty, we shall at our option, repair or replace any war-

ranted part during the applicable period. If you are in doubt or experience any difficulty, please consult a Hayter

Authorised Service Dealer for clarification..

To qualify for the extended warranty (second and third year) of the three year limited warranty, the machine must

have annual services carried out by an Authorised Hayter Service Dealer. These chargeable services should be

carried out within 12 and 24 months of the date of purchase.

Excluded from the extended warranty period are those items which are subject to normal wear and tear e.g. tyres,

wheels, cutterbars, cables, batteries and other consumable wearing parts.

All consumer machines which are fitted with a genuine Hayter friction disc as original equipment, before use, are

covered by a Lifetime Warranty against the engine crankshaft bending. Note: friction washers, blade brake

units and other such devices are not applicable. Only machines fitted with a genuine Hayter friction disc, which

are used in accordance with the recommended operating and maintenance procedures, are covered.

This warranty does not apply to any unit that has been tampered with, altered, misused, abused or used for hire,

and will become invalid if non genuine Hayter parts are fitted. This warranty does not cover minor mechanical

adjustments unless they are due to defective materials or workmanship. Consult the Owner’s Handbook or a

Hayter Authorised Service Dealer for assistance when making these adjustments.

A warranty period of 90 days applies to machines used for commercial purposes.

To make a warranty claim, return the unit to a Hayter authorised dealer along with proof of purchase stating the

machine serial number and date of purchase. The service receipt(s) or this Owner’s Handbook with the 1st/2nd

year service boxes fully completed, must be produced as proof of entitlement to the extended warranty period.

Subject to the conditions and exclusions in this limited warranty, the authorised dealer will, at our option, repair or

replace any warranted part within the duration of the warranty period.

This limited warranty gives you specific legal rights and is in addition to any statutory rights to which you may be

entitled and your statutory rights are not affected by this warranty. If you need additional information concerning

this written warranty, or assistance in obtaining services, please write to:

HAYTER LIMITED, Service Department, Spellbrook, Bishop’s Stortford, Hertfordshire. CM23 4BU.

UK ONLY: Details of your local Hayter authorised dealer are contained in Yellow Pages or contact: Freephone 0800 616298.

1st

Year

Service

Record

2nd

Year

Service

Record

Date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Signed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Signed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

F-050732L

CONTENTS

LIMITED WARRANTY 10

INTERNATIONAL PICTORIALS 11

OWNER’S INFORMATION 12

SAFE OPERATION PRACTICES 12

ASSEMBLY 13

OPERATION 14

MAINTENANCE 15

TROUBLE SHOOTING CHART 19

INTERNATIONAL PICTORIALS

IMPORTANT: The following pictorials are lo-

cated on your unit or on literature supplied

with the product. Before you operate the

unit, learn and understand the purpose for

each pictorial.

NOTE: Illustrations and pictorials begin

on page 2.

Safety Warning Pictorials (Figure 37)

1WARNING

2IMPORTANT: Read Owner’s Manual

Before Operating This Machine.

3WARNING: Thrown Objects. Keep

Bystanders Away. Read User Instructions

Before Operating This Machine.

4WARNING: Do Not Use This Machine On

Slopes Greater Than 10 Degrees.

5DANGER: Keep People, Especially

Children, Away From Unit.

6DANGER: No Step.

7DANGER: Keep Feet And Hands Away

From Rotating Blade.

8Declared airborne sound power level of 100

dB(A) is in accordance with Directive

2000/14/EC.

9DANGER: Disconnect Spark Plug Wire

Before Servicing Unit.

10 WARNING: Hot Surface.

11 WARNING: Use Caution When Connecting

Or Disconnecting Accessories.

12 WARNING: Crushed Fingers.

13 IMPORTANT: Follow Instructions In

Owner’s Manual To Level The Deck.

14 WARNING: Stay Clear Of Mower Blade As

Long As Engine Is Running.

Control And Operating Pictorials

(Figure 38)

1Engine Start

2Lights

3Engine Run

4Engine Stop

5Engine Run

6Brake

7Parking Brake

8Clutch

9Slow

10 Fast

11 Choke

12 Oil

13 Blade Rotation Control

14 Raise

15 Fuel

Declared vibration emission values in accordance with Directive 98/37/EC.

Vibration Emission according to BS EN 1032: Seat 1,64 m/s2,

Right Running Board 2,19 m/s2, Left Running Board 2,90 m/s2

Vibration Emission according to BS EN 1033: Steering Wheel 4,39 m/s2

Values determined with operator in operating position when the machine was

operated stationary on a concrete surface at 2850 min-1.

Declared airborne noise emissions in accordance with Directive 2000/14/EC,

Annex VIII.

Sound Pressure Level at operator position 86 dB.

Values determined at ear according to the specifications of EN ISO 11201.

2850

MADE IN USA BY MURRAY INC.,

LAWRENCEBURG, TENNESSEE

F-050732L

OWNER’S INFORMATION

Know your product: If you understand the unit

and how the unit operates, you will get the best

performance. As you read this manual, compare

the illustrations to the unit. Learn the location

and the function of the controls. To help prevent

an accident, follow the operating instructions

and the safety rules. Keep this manual for future

reference.

WARNING: Look for this symbol to indicate

important safety precautions. This symbol

indicates: “Attention! Become Alert! Your

Safety Is At Risk.”

Responsibility Of The Owner

WARNING: This cutting machine is

capable of amputating hands and

feet and throwing objects. Failure

to observe the following safety instructions

could result in serious injury or death to

the operator or bystanders.

The responsibility of the owner is to

follow the instructions below.

SAFE OPERATION PRACTICES

For Ride-On (Riding)

Rotary Mower Machines

Training

1. Read the instructions carefully. Be familiar

with the controls and the proper use of the

equipment.

2. Never allow children or people unfamiliar

with these instructions to use the mower.

Local regulations may restrict the age of

the operator.

3. Never mow while people, especially

children, or pets are nearby.

4. Keep in mind that the operator or user is

responsible for accidents or hazards occur-

ring to other people or their property.

5. Do not carry passengers.

6. All drivers should seek and obtain pro-

fessional and practical instruction. Such

instruction should emphasize:

a. the need for care and concentration

when working with ride-on machines;

b. control of a ride-on machine sliding

on a slope will not be regained by the

application of the brake. The main

reasons for loss of control are:

linsufficient wheel grip;

lbeing driven too fast;

linadequate braking

lthe type of machine is unsuitable

for its task;

llack of awareness of the effect of

ground conditions, especially

slopes;

lincorrect hitching and load dis-

tribution.

Preparation

1. While mowing, always wear substantial

footwear and long trousers. Do not operate

the equipment when barefoot or wearing

open sandals.

2. Thoroughly inspect the area where the

equipment is to be used and remove all ob-

jects which may be thrown by the machine.

3. WARNING - Petrol is highly flammable.

a. Store fuel in containers specifically de-

signed for this purpose.

b. Refuel outdoors only and do not

smoke while refuelling.

c. Add fuel before starting the engine.

Never remove the cap of the fuel tank

or add petrol while the engine is run-

ning or when the engine is hot.

d. If petrol is spilled, do not attempt to

start the engine but move the machine

away from the area of spillage and

avoid creating any source of ignition

until petrol vapours have dissipated.

e. Replace all fuel tanks and container

caps securely.

4. Replace faulty silencers.

5. Before using, always visually inspect to see

that the blades, blade bolts and cutter as-

sembly are not worn or damaged. Replace

worn or damaged blades and bolts in sets

to preserve balance.

6. On multi-blade machines, take care as ro-

tating one blade can cause other blades to

rotate.

Operation

1. Do not operate the engine in a confined

space where dangerous carbon monoxide

fumes can collect.

2. Mow only in daylight or in good artificial

light.

3. Before attempting to start the engine, dis-

engage all blade attachment clutches and

shift into neutral.

4. Do not use on slopes of more than 10 de-

grees.

5. Remember there is no such thing as a

“safe” slope. Travel on grass slopes re-

quires particular care. To guard against

overturning:

a. do not stop or start suddenly when

going up or downhill;

b. engage clutch slowly, always keep

machine in gear, especially when tra-

velling downhill;

c. machine speeds should be kept low

on slopes and during tight turns;

d. stay alert for humps and hollows and

other hidden hazards;

e. never mow across the face of the

slope, unless the mower is designed

for this purpose.

6. Use care when pulling loads or using heavy

equipment.

a. Use only approved drawbar hitch

points.

b. Limit loads to those you can safely

control.

c. Do not turn sharply. Use care when

reversing.

d. Use counterweight(s) or wheel

weights when suggested in the In-

struction Book.

7. Watch out for traffic when crossing or near

roadways.

8. Stop the blades rotating before crossing

surfaces other than grass.

9. When using any attachments, never direct

discharge of material toward bystanders

nor allow anyone near the machine while in

operation.

10. Never operate the mower with defective

guards or shields, or without safety protec-

tive devices in place.

11. Do not change the engine governor set-

tings or overspeed the engine. Operating

an engine at excessive speed may in-

crease the hazard of personal injury.

12. Before leaving the operator’s position

a. disengage the power take-off and

lower the attachments;

b. change into neutral and set the park-

ing brake;

c. stop the engine and remove the key.

13. Disengage drive to attachments, stop the

engine, and disconnect the spark plug

wire(s) or remove the ignition key

a. before cleaning blockages or unclog-

ging chute;

b. before checking, cleaning or working

on the mower;

c. after striking a foreign object. Inspect

the mower for damage and make re-

pairs before restarting and operating

the equipment;

d. if the machine starts to vibrate abnor-

mally (check immediately).

14. Disengage drive to attachments when

transporting or not in use.

15. Stop the engine and disengage drive to at-

tachment

a. before refuelling;

b. before removing the grass catcher;

c. before making height adjustment un-

less adjustment can be made from the

operator’s position.

16. Reduce the throttle setting during engine

run-out and, if the engine is provided with a

shut-of f valve, turn the fuel off at the con-

clusion of mowing.

17. Before and when backing, look behind and

down for small children.

18. Use extra care when approaching blind

corners, shrubs, trees or other objects that

may obscure vision.

Maintenance and Storage

1. On multi-blade machines, take care as ro-

tating one blade can cause other blades to

rotate.

2. When machine is to be parked, stored or

left unattended, lower the cutting means

unless a positive mechanical lock is used.

3. Keep all nuts, bolts, and screws tight to be

sure the equipment is in safe working

condition.

4. Never store the equipment with petrol in the

tank inside a building where fumes may

reach an open flame or spark.

5. Allow the engine to cool before storing in

any enclosure.

6. To reduce the fire hazard, keep the engine,

silencer, battery compartment and petrol

storage area free of grass, leaves, or ex-

cessive grease.

7. Check the grass catcher frequently for

wear or deterioration.

8. Replace worn or damaged parts for safety.

9. If the fuel tank has to be drained, this

should be done outdoors.

F-050732L

ASSEMBLY

All fasteners are in the parts bag. Do not discard

any parts or material until the unit is assembled.

WARNING: Before doing any as-

sembly or maintenance to the

mower, remove the wire from the

spark plug.

NOTE: In this instruction book, left and right

describe the location of a part with the oper-

ator on the seat.

NOTE: Illustrations and pictorials begin on

page 2.

NOTE: To assemble the following loose

parts, use the fasteners shown at full size in

Figure 39.

How To Install The Front Wheels

(Figure 1)

NOTE: Use a piece of wood about 4 feet (1.25

meters) long to raise the front of the tractor.

If a piece of wood cannot be found, get

another person to help lift the tractor. Be

careful, do not let the tractor fall.

1. Raise the front of the tractor. Set a support

(block of wood) under the tractor.

2. Make sure the valve stem (2) is to the out-

side of the tractor. Slide the front wheel (1)

on the spindle (3).

3. Fasten each front wheel (1) with washer

(4), washer (7), and cotter pin (5). Bend the

ends of the cotter pin (5) appart to keep the

front wheel (1) on the spindle (3).

4. After the front wheels (1) are installed, lift

the tractor from the support. Roll the tractor

off of the container.

5. If your tractor has hub caps (6), install the

hub caps (6). Make sure the washers (4)

hold the hub caps (6) in place.

Check The Tyres

NOTE: The tires were over inflated for ship-

ment. The correct air pressure is shown on

the side of the tire.

Check the air pressure in the tyres. Tyres with too

much air pressure will cause the unit to ride rough.

Also, the wrong air pressure will keep the mower

housing from cutting level. The correct air pres-

sure is shown on the side of the tire.

Check The Level Of The Mower

Housing

Make sure the level of cut is still correct. After you

mow a short distance, look at the area that was cut.

If the mower housing does not cut level, see the in-

structions on “How To Level The Mower Housing”

in the Maintenance section of this instruction book.

How To Install The Seat (Figure 2)

1. Carefully remove the plastic bag from the

seat (1).

2. Align the holes in the seat hinge (2) to the

holes in the seat (1). Fasten the seat (1) to

the seat hinge (2) with the fasteners (4) and

(5).

3. Check the operating position of the seat (1).

If the seat (1) needs to be adjusted, loosen

the two wing bolts (5). Slide the seat (1) for-

ward or backward along the seat adjusting

holes (3). Tighten the wing bolts (5).

How To Assemble The Steering Wheel

(Figure 3)

1. Make sure the front wheels point forward.

2. Slide the cover (3) over the steering post

(2). Make sure the collar of the cover (3) is

on top.

(Figure 34) NOTE: Before attachment of the

steering wheel (1), make sure that the front

wheels point forward and are straight. For

proper alignment of the steering wheel, see

illustration 34.

3. Slide the steering wheel (1) onto the steer-

ing post (2).

4. Attach the steering wheel (1) to the steer-

ing post (2) with screw (4) and washer (6).

5. Some models have an optional insert (7) in

the parts bag. Attach the insert (7) to the

center of the steering wheel (1).

How To Assemble The Grass Bag

1. (Figure 5) Slide the top tube (1) onto the

wire frame (2). Make sure the handles (3)

on the top tube (1) and the wire frame (2)

are on top.

2. Attach the struts (4) to the INSIDE of the

mounting tabs (5) with bolt (6) and nut (7).

Make sure the head of bolt (6) is on the out-

side and nut (7) is locked against the strut

(4).

3. (Figure 6) Slide the frame assembly (8) into

the grass bag (9). Make sure the Velcro

flap (10) is on top.

4. (Figure 7) Open the Velcro flap (10). Slide

the handle (3) through the opening and se-

cure the Velcro flap (10) under the handle

(3).

5. Attach the clips (11) to the frame assembly

(8).

How To Mount The Grass Bag

1. (Figure 8) To lift the grass bag assembly,

use the grass bag handles (3).

2. (Figure 9) Mount the top of the grass bag

assembly (12) onto the rear plate hinges

(13).

3. (Figure 8) When mounting the top of the

grass bag (9), hold the bottom of the grass

bag (9) slightly away from the rear plate

(14).

4. (Figure 10) Then, lower the grass bag (9)

until the bottom is against the rear plate.

5. (Figure 9) Push down on the rear handle. A

locking spring (15) on the rear plate will se-

cure the bottom of the grass bag assembly

(12).

Maintenance Free Battery (Figure 4)

IMPORTANT: Before you attach the battery

cables to the battery, check the battery date.

The battery date tells if the battery must be

charged.

1. Check the top and the side of the battery (1)

for the location of the battery date.

2. If the battery (1) is put into service before

the battery date, the battery cables can be

attached without charging the battery (1).

See “How To Install The Battery Cables”.

3. If the battery (1) is put into service after the

battery date, the battery (1) must be

charged. See “How To Charge The Mainten-

ance Free Battery”.

How To Charge The Battery (Figure 4)

WARNING: When you charge the

battery, do not smoke. Keep the bat-

tery away from any sparks. The

fumes from the battery acid can cause an

explosion.

1. Remove the battery (1) and battery tray (3).

2. Remove the protective cap from the battery

terminal.

3. Use a 12 volt battery charger to charge the

battery (1). Charge at a rate of 6 amperes

for one hour. If you do not have a battery

charger, have an authorized service centre

charge the battery.

4. Install the battery (1) and battery tray (3).

Make sure the positive (+) terminal (4) is on

the left side.

How To Install The Battery Cables

(Figure 4)

WARNING: To prevent sparks, fasten

the red cable to the positive (+) ter-

minal before you connect the black

cable.

1. Remove the protective cap from the battery

terminal.

2. Slide the terminal cover (2) onto the red

cable (5). Fasten the red cable (5) to the

positive (+) terminal (4) with the fasteners

(6) and (7).

3. Fasten the black cable 8 to the negative (-)

terminal with the fasteners (6) and (7).

How To Prepare The Engine

NOTE: The engine was shipped from the fac-

tory filled with oil. Check the level of the oil.

Add oil as needed.

NOTE: The operation of a new engine will

sometimes result in a slight amount of

smoke. This smoke is caused by paint or oil

on or around the muffler. This is normal and

only expected during initial operation.

A separate engine manual is also included with the

unit. See this engine manual for the manufactur-

er’s instructions for the type of petrol and oil to use.

Before you use the unit, read the information on

safety, operation, maintenance, and storage.

WARNING: Follow the engine manu-

facturer’s instructions for the type o

petrol and oil to use. Always use a

safety petrol container. Do not smoke when

adding petrol to the engine. When inside an

enclosure, do not fill with petrol. Before you

add petrol, stop the engine. Let the engine

cool for several minutes.

Important! Before You Start Mowing

rCheck the engine oil.

rFill the fuel tank with petrol.

rCheck the air pressure of the tyres.

rCheck the level of the mower hous-

ing.

rAttach the battery cables.

rMake sure the wire is attached to

the spark plug.

F-050732L

OPERATION

NOTE: Illustrations and pictorials begin on

page 2.

Location Of Controls (Figure 13)

Blade Rotation Control (1): Use the blade

rotation control to start and stop the rotation of

the blade.

Clutch / Brake Pedal (2): The pedal has two

functions. The first function is a clutch. The

second function is a brake.

Headlight Switch (3): The headlight switch is

the first part of the ignition switch. To use the

lights with the engine running, turn the key to the

position for the lights.

Ignition Switch (3): Use the ignition switch to

start and stop the engine.

Shift Lever (4): Use the shift lever to change

the speed of the unit.

Lift Lever (5): Use the lift lever to change the

height of cut.

Parking Brake Lever (6): Use the parking brake

lever to engage the brake when you leave the

unit.

Throttle Control Lever (7): Use the throttle

control lever to increase or decrease the speed

of the engine.

How To Use The Throttle Control

(Figure 13)

Use the throttle control (7) to increase or

decrease the speed of the engine.

CAUTION: Always operate the engine with

the throttle control in the FAST position. If

the engine runs for several minutes at slower

than the FAST position, the engine and trans-

mission will overheat and can be damaged.

1. The FAST position is marked with a detent.

For normal operation and when using a

grass bagger, move the throttle control to the

FAST position. For maximum charging of the

battery and for a cooler running engine, oper-

ate the engine in the FAST position.

2. For transport and to tow pull behind attach-

ments, move the throttle control to the SLOW

position.

3. The engine governor is set at the factory for

maximum performance. Do not adjust the

governor to increase the speed of the en-

gine.

How To Use The Blade Rotation Control

(Figure 13)

Use the blade rotation control (1) to engage

the blade(s).

1. Before you start the engine, make sure the

blade rotation control (1) is in the DISEN-

GAGE position.

2. Move the blade rotation control (1) to the

ENGAGE position to rotate the blade(s).

NOTE: If the engine stops when you en-

gage the blade(s), the seat switch or the

grass bag switch is not activated.

3. Move the blade rotation control (1) to the

DISENGAGE position to stop the blade(s).

Before you leave the operator’s position,

make sure the blade(s) has stopped rotating.

4. Before you ride the unit across a sidewalk or

a road, move the blade rotation control (1)

to the DISENGAGE position.

WARNING: Always keep your

hands and feet away from the

blade, deflector opening, and the

mower housing when the engine runs.

How To Use The Shift Lever (Figure 13)

To change the forward speed or the direction of

the unit, follow the steps below.

CAUTION: Before you move the shift lever,

completely push the clutch/brake pedal for-

ward to stop the unit. If the unit is not

stopped, the gearbox can be damaged.

1. Completely push the clutch/brake pedal (2)

forward to stop the unit. Keep your foot on

the pedal.

2. Move the throttle control lever (7) to the

SLOW position.

3. To go forward, move the shift lever (4) to a

forward speed setting. To go backward,

move the shift lever (4) to reverse.

4. Slowly release the clutch/brake pedal (2).

Do not keep your foot on the pedal.

5. Move the throttle control (7) to the FAST

position.

How To Use The Parking Brake

(Figure 13)

1. Completely push the clutch/brake pedal (2)

forward.

2. Lift the parking brake lever (6).

3. Remove your foot from the clutch/brake

pedal (2) and then release the parking

brake lever (6). Make sure the parking brake

will hold the unit.

4. To release the parking brake (6), completely

push the clutch/brake pedal (2) forward.

The parking brake will automatically release.

WARNING: Before you leave the

operator’s position, move the shift

lever to the neutral (N) position. Set

the parking brake. Move the blade rotation

control to the DISENGAGE position. Stop

the engine and remove the ignition key.

How To Change The Cutting Height

(Figure 13)

To change the cutting height, raise or lower the

lift lever (5) as follows.

1. Move the lift lever (5) forward to lower the

mower housing and back to raise the mower

housing.

2. When you ride on a sidewalk or road, move

the lift lever (5) to the highest position and

move the blade rotation control to the DIS-

ENGAGE position.

How To Stop The Unit (Figure 13)

1. Completely push the clutch/brake pedal (2)

forward to stop the unit. Keep your foot on

the pedal.

2. Move the blade rotation control (1) to the

DISENGAGE position.

3. Move the shift lever (4) to the NEUTRAL

position.

4. Set the parking brake (6).

WARNING: Make sure the parking

brake will hold the unit.

5. Move the throttle control (7) to the SLOW

position.

6. To stop the engine, turn the ignition key (3)

to the OFF position. Remove the key.

7. (Figure 35) Some models have a fuel shut-

off valve (1) located under the fuel tank. If

equipped, close the fuel shut-off (1) valve.

How To Transport The Unit

To transport the unit, follow the steps below.

1. Move the blade rotation control to the DIS-

ENGAGE position.

2. Raise the lift lever to the highest position.

3. Move the throttle control to a position be-

tween SLOW and FAST.

4. To go faster, move the shift lever to a faster

speed.

How To Operate With The Mower

Housing

IMPORTANT: When you operate with the

mower housing, always operate with the

throttle control in the FAST position.

1. Start the engine.

2. Move the lift lever to a height of cut position.

In high or thick grass, cut the grass in the

highest position first and then lower the

mower housing to a lower position.

3. Move the throttle control to the SLOW posi-

tion.

4. Slowly move the blade rotation control to the

ENGAGE position.

5. Push the clutch/brake pedal completely for-

ward.

6. Move the shift lever to one of the speed set-

tings.

NOTE: When you mow in heavy grass or

mow with a bagger, put the shift lever in

the slowest speed.

7. Slowly release the clutch/brake pedal.

8. Move the throttle control to the FAST posi-

tion. If you need to go faster or slower, stop

the unit and move the shift lever to another

speed setting.

9. Make sure the level of cut is still correct.

After you mow a short distance, look at the

area that was cut. If the mower housing does

not cut level, see the instructions on “How To

Level The Mower Housing” in the Mainten-

ance section.

WARNING: For better control of the

unit, select a safe speed.

How To Operate On Hills

WARNING: Do not ride up or down

slopes that are too steep to back

straight up. Never ride the unit

across a slope.

1. Before you ride up or down a hill, move the

shift lever to the slowest speed.

2. Do not stop or change speed settings on a

hill. If you must stop, quickly push the clutch/

brake pedal forward and set the parking

brake.

F-050732L

3. To start again, make sure the shift lever is in

the slowest speed. Move the throttle control

to the SLOW position. Slowly release the

pedal.

4. If you must stop or start on a hill, always

have enough space for the unit to roll when

you release the brake and engage the clutch.

5. Be very careful when you change directions

on a hill. When on a slope or in a turn on a

hill, move the throttle control to the SLOW

position to help prevent an accident.

How To Use The Grass Bagger

WARNING: Do not ride up or down

slopes that are too steep to back

straight up. Never ride the unit

across a slope.

Operation

To operate with the grass bagger, follow the

steps below.

1. Start the engine.

2. Move the throttle control to FAST position.

3. Move the shift lever to FIRST (1) position. To

fill the grass bag, always operate at the

slowest speed.

4. If the height of the grass is more than 31/2

inches (9cm), cut the grass with the mower

housing in the highest position. Then, lower

the mower housing and cut the grass again.

You can also cut at 1/2 to 2/3 of the full cutting

width of the mower housing.

How To Clear The Connector Tube And

The Extension Tube

If the connector tube or the extension tube

becomes filled with grass, clear as follows.

1. Move the blade rotation control to the DIS-

ENGAGE position.

2. Move the shift lever to the neutral (N) posi-

tion.

3. Engage the parking brake.

4. Stop the engine.

5. (Figure 8) Remove the grass bagger (9).

6. (Figure 11) Use a long stick (1) to push any

grass and debris from the connector tube

(2) or the extension tube.

7. If the connector must be removed, see “How

To Remove The Connector Tube” in the

maintenance section.

How To Empty The Grass Bagger

1. Move the blade rotation control to the DIS-

ENGAGE position.

2. Move the shift lever to the neutral (N) posi-

tion.

3. Engage the parking brake.

4. (Figure 12) Raise the rear of the grass bag

(9).

Before Starting The Engine

Check the oil

NOTE: The engine was shipped from the fac-

tory filled with oil. Check the level of the oil.

Add oil as needed. See the engine manufac-

turer’s instructions for the type of petrol and

oil to use.

1. Make sure the unit is level.

NOTE: Do not check the level of the oil

while the engine runs.

2. Check the oil. Follow the procedure in the

engine manufacturer’s instructions.

3. If necessary, add oil until the oil reaches the

FULL mark on the dipstick. The quantity of oil

needed from ADD to FULL is shown on the

dipstick. Do not add too much oil.

Add Petrol

WARNING: Always use a safety

petrol container. Do not smoke

when adding petrol to the fuel tank.

Do not add petrol when you are inside an

enclosure. Before you add petrol, stop the

engine and let the engine cool for several

minutes.

1. (Figure 14) Fill the fuel tank (1) to the FULL

(2) position with regular unleaded petrol. Do

not use premium unleaded petrol. Make sure

the petrol is fresh and clean. Leaded petrol

will increase deposits and shorten the life of

the valves.

2. (Figure 35) Some models have a fuel shut-

off valve located under the fuel tank. If

equipped, turn the fuel shut-off valve (1)

1/4 turn to the OPEN position.

How To Start The Engine

WARNING: The electrical system

has an operator presence system

that includes a sensor switch for

the seat. These components tell the

electrical system if the operator is sitting

on the seat. This system will stop the

engine when the operator leaves the seat.

For your protection, always make sure this

system operates correctly.

NOTE: The engine will not start unless you

depress the clutch/brake pedal or engage the

parking brake and move the blade rotation

control to the DISENGAGE position.

1. Push the clutch/brake pedal completely for-

ward. Keep your foot on the pedal.

2. Move the shift lever to the neutral (N) posi-

tion.

3. Make sure the blade rotation control is in the

DISENGAGE position.

4. Move the throttle control completely forward

to the CHOKE or FAST position. Some mo-

dels have a separate choke knob. Pull the

choke knob to the full CHOKE position.

5. Turn the ignition key to the START position.

NOTE: If the engine does not start after

four or five tries, move the throttle control

to the FAST position. Again try to start the

engine. If the engine will not start, see the

TROUBLE SHOOTING CHART.

6. Slowly move the throttle control to the SLOW

position.

7. To start a hot engine, move the throttle con-

trol to a position between FAST and SLOW.

Mowing And Bagging Tips

1. For a lawn to look better, check the cutting

level of the mower housing. See “How To

Level The Mower Housing” in the Mainten-

ance section.

2. For the mower housing to cut level, make

sure the tyres have the correct amount of air

pressure. The correct air pressure is shown

on the side of the tyres.

3. Every time you use the unit, check the blade.

If the blade is bent or damaged, immediately

replace the blade. Also, make sure the nut

for the blade is tight.

4. Keep the blade(s) sharpened. Worn blades

will cause the ends of the grass to turn

brown.

5. If the grass is very high, cut two times to de-

crease the load on the engine. First cut with

the mower housing in the highest position

and then lower the mower housing for the

second cut.

6. Operate the engine with the throttle in FAST

position and the shift lever in first or second

gear.

7. For better cutting performance and a quality

cut, mow with the shift lever in one of the

slower speeds.

8. After each use, clean the bottom and top of

the mower housing for better performance.

Also, a clean mower housing will help pre-

vent a fire.

MAINTENANCE

NOTE: Illustrations and pictorials begin on

page 2.

General Recommendations

1. The owner’s responsibility is to maintain this

product. This will extend the life of the prod-

uct and is also necessary to maintain war-

ranty coverage.

2. Check the spark plug, drive brake, lubricate

the unit, and clean the air filter once a year.

3. Check the fasteners. Make sure all fasteners

are tight.

4. Follow the Maintenance section to keep the

unit in good operating condition.

WARNING: Before you make an in-

spection, adjustment, or repair to

the unit, disconnect the wire to the

spark plug. Remove the wire from the

spark plug to prevent the engine from

starting by accident.

NOTE: Torque is measured in metric N-m

(foot pounds). This measurement describes

how tight a nut or bolt must be. The torque is

measured with a torque wrench.

How To Remove The Connector Tube

For good bagging performance, the connector

tube must be clean and free from grass and

debris. Remove and clean the connector tube

as follows.

To Remove

1. Move the blade rotation control to the DIS-

ENGAGE position.

F-050732L

2. Move the shift lever to the neutral (N) posi-

tion.

3. Engage the parking brake.

4. Stop the engine.

5. Move the lift lever to the middle cutting posi-

tion.

6. (Figure 15 and Figure 16) Disconnect the

rubber strap (1) from the latch pin (2) on

the connector tube (3).

7. (Figure 17) Hold the handles (4). Remove

the grass bag (5).

8. (Figure 18) Pull the connector tube (3)

through hole in rear plate (6).

9. Clean the connector tube (3) with soap and

water.

To Install

1. (Figure 16 and Figure 18) Slide the flange

(7) end of the connector tube (3) through

hole in rear plate (6).

2. (Figure 16) Slide the flange (7) end of the

connector tube (3) over the extension tube

(8).

3. (Figure 15 and Figure 16) Attach the

rubber strap (1) to the latch pin (2) on the

connector tube (3).

4. Install the grass bag.

Inspect Blade (Figure 19)

WARNING: Before you inspect or

remove the blade, disconnect the

wire to the spark plug. If the blade

hits an object, stop the engine. Check the

unit for damage. The blade has sharp

edges. When you hold the blade, use

gloves or cloth material to protect your

hands.

If you keep the blade (1) sharp and inspect the

blade for damage, the blade will cut better and

be more safe to operate. Frequently check the

blade for excessive wear, cracks, or other

damage. Frequently check the nut (3) that holds

the blade (1). Keep the nut (3) tight. If the blade

hits an object, stop the engine. Disconnect the

wire to the spark plug. See if the blade is bent or

damaged. Check the blade adapter (5) for

damage. Before you operate the unit, replace

damaged parts with original equipment parts.

See the authorized service centre in your area.

Every three years, have an authorized service

person inspect the blade or replace the old

blade with an original equipment part.

How To Remove And Install The Blade

(Figure 19)

1. Remove the mower housing. See the instruc-

tions on “How To Remove The Mower Hous-

ing”.

2. Use a piece of wood to keep the blade from

rotating.

3. Remove the nut (3) that holds the blade (1).

4. To remove the blade (1) from the air assist

fan (8), remove fasteners (9) and (10).

5. Check the blade (1) and the blade adapter

(5) according to the instructions for “Inspect

Blade”. Check the air assist fan (8) for dam-

age. Replace badly worn or damaged parts

with original equipment parts. See an author-

ized service centre in your area.

6. Clean the top and bottom of the mower hous-

ing. Clean the air assist fan (8). Remove all

the grass and debris.

7. Assemble the blade (1) and air assist fan

(8) with fasteners (9) and (10). Tighten the

bolt (9) that holds the blade (1) to a torque

of 6,8 N-m (5 foot pounds).

8. Mount the blade (1) and blade adapter (5)

on the mandrel (6).

9. Mount the blade (1) so that the hi-lift edges

(7) are up. If the blade is upside down, the

blade will not cut correctly and can cause an

accident.

10.Fasten the blade (1) with the original

washers and nut (3). Make sure the outside

rim of the Belleville washer (2) is against

the blade (1).

WARNING: Always keep the nut (3)

tight that holds the blade (1). A

loose nut or blade can cause an

accident.

11. Tighten the nut (3) that holds the blade (1) to

a torque of 41,5 N-m (30 foot pounds) .

12.Install the mower housing. See “How To Re-

move The Mower Housing”.

How To Adjust The Blade Rotation

Control

WARNING: To prevent an injury, the

blade rotation control must operate

correctly.

In normal usage, the blade rotation control will

not require an adjustment. However, if the

cutting performance decreases or the quality of

cut is poor, make the following changes.

1. When you mow, make sure the throttle con-

trol in in the FAST position.

2. (Figure 20) Move the blade rotation control

to the DISENGAGE position (1).

3. Stop the engine. Disconnect the wire from

the spark plug.

4. Check the blade(s). Keep a sharp edge on

the blade(s). A blade that is not sharp will

cause the tips of the grass to become brown.

5. (Figure 21) Disconnect the blade drive

spring (2) from the blade control rod (1).

Move the blade drive spring (2) to the

middle hole (4). This will increase the tension

on the mower drive belt.

6. Attach the wire to the spark plug. Mow for a

short distance and again check the quality of

cut. If necessary, move the blade drive

spring (2) to the bottom hole (5)

7. Again check the quality of cut. If the quality of

cut has not improved, replace the mower

drive belt. See “How To Replace The Mower

Drive Belt”. If replacing the belt does not cor-

rect the problem, take the unit to an author-

ized service centre.

8. Move the blade rotation control to the DIS-

ENGAGE position. Stop the engine.

9. (Figure 22) Check the operation of the blade

brake. Rotate the mandrel pulley (5) with

your hand. Make sure the brake pad (7) is

pressed tightly against the mandrel pulley

(5).

WARNING: If the brake pad (7) does

not press tightly against the man-

drel pulley (5), take the unit to an

authorized service centre.

10.(Figure 20) Move the blade rotation control

to the ENGAGE position (2).

11. (Figure 22) Check the pad for the blade

brake (7). If the pad is excessively worn or

damaged, replace the brake pad assembly.

Correct replacement parts and assistance

are available from an authorized service

centre.

12.Attach the wire to the spark plug. Mow for a

short distance and again check the operation

of the blade rotation control.

13.When you move the blade rotation control to

the DISENGAGE position, all movement will

stop within five seconds. If there is move-

ment of the belt or the blade(s) continue to

rotate, engage and disengage the blade rota-

tion control five times to remove any excess

rubber from a new mower drive belt. If you

need assistance, take the unit to an author-

ized service centre.

14.(Figure 21) If you replace the mower drive

belt, move the blade drive spring (2) to the

top hole (3).

How To Adjust The Shift Lever

(Figure 30)

If the NEUTRAL position on the shift lever does

not match neutral on the gearbox, adjust the

shift lever as follows.

1. Stop the engine.

2. Disconnect the adjuster nut (2) from the

shifter bracket (3).

3. Make sure the shift lever is in the NEUTRAL

position.

4. Push the unit forward. Make sure the gear-

box is in neutral.

5. To align the adjuster nut (2) with the hole in

the shifter bracket (3), turn the adjuster nut

(2).

6. Connect the adjuster nut (2) to the shifter

bracket (3).

7. Make sure the NEUTRAL position on the

shift lever matches neutral on the gearbox.

How To Check And Adjust The Clutch

(Figure 23)

If the motion drive belt is loose, the clutch will

slip when: going up a hill, pulling a heavy load,

or the unit will not move forward. Adjust the

clutch as follows.

WARNING: Before you make an in-

spection, adjustment, or repair to

the unit, disconnect the wire to the

spark plug. Remove the wire from the

spark plug to prevent the engine from

starting by accident.

1. Check the routing of the motion drive belt.

Make sure the belt is installed correctly and

is inside all the belt guides.

2. Remove the cotter pin (1), washer (2), and

brake spring (3) from the adjustable nut

(4).

3. Disconnect the adjustable nut (4) from the

brake lever assembly (5) and the parking

brake latch (6).

4. Align the hole in the brake lever (5) with the

hole in the frame. Hold the brake lever (5) in

place with a 6 mm pin or bolt (7).

F-050732L

5. Pull the clutch rod forward until tight. Turn the

adjustable nut (4) until the nut will fit through

the hole in the brake lever (5).

6. Assemble the adjustable nut (4) to the

parking brake latch (6), brake lever (5) and

brake spring (3). Fasten with the washer (2)

and cotter pin (1).

7. Remove the 6 mm pin or bolt (7).

8. If the belt still slips after the clutch has been

adjusted, then the motion drive belt is worn

or damaged and must be replaced. See

“How To Replace The Motion Drive Belt”.

How To Check And Adjust The Drive

Brake (Figure 24)

Completely push the clutch/brake pedal forward.

Set the parking brake. Move the shift lever to the

neutral (N) position. Push the unit. If the rear

wheels rotate, adjust or replace the brake pads.

Adjust the drive brake (1) as follows.

1. The location of the drive brake (1) is on the

right side of the gearbox (3).

2. Make sure the parking brake is set and the

shift lever is in neutral (N). Turn the hex nut

(2) in a clockwise direction until the rear

wheels do not turn when the unit is pushed

forward.

3. Release the parking brake and push the unit.

If the unit does not roll, turn the hex nut (2)

in a counter-clockwise direction until the unit

rolls.

4. Set the parking brake. Push the unit. If the

rear wheels do not turn, the drive brake (1)

is correctly adjusted. Release the parking

brake.

WARNING: If you cannot correctly

adjust the drive brake, replace the

brake pads. Correct replacement

parts and assistance are available from an

authorized service centre.

How To Remove The Battery (Figure 4)

To charge or clean the battery (1), remove the

battery (1) from the unit as follows.

WARNING: To prevent sparks, dis-

connect the black battery cable (8)

from the negative (-) terminal be-

fore you disconnect the red cable (5).

WARNING: The battery contains

sulphuric acid which is harmful to

the skin, eyes and clothing. If the

acid gets on the body or clothing, wash

with water.

1. Disconnect the black cable (8) from the

negative (-) terminal.

2. Disconnect the red cable (5) from the posi-

tive (+) terminal (4).

3. Lift the battery tray (3) and the battery (1)

out of the unit.

How To Charge The Battery (Figure 4)

WARNING: When you charge the

battery, do not smoke. Keep the

battery away from any sparks. The

fumes from the battery acid can cause an

explosion.

1. Before you charge the battery (1), remove

the battery (1).

2. To charge the battery (1), use a 12 volt bat-

tery charger. Charge at a rate of 6 amperes

for 1 hour.

3. Install the battery (1).

WARNING: To prevent sparks,

fasten the red cable to the positive

(+) terminal before you connect the

black cable.

4. Fasten the red cable (5) to the positive (+)

terminal (4) with the fasteners as shown.

5. Fasten the black cable (8) to the negative

(-) terminal with the fasteners as shown.

How To Level The Mower Housing

(Figure 25 and Figure 26)

If the mower housing is level, the blade will cut

easier and the lawn will look better.

WARNING: Before you make an in-

spection, adjustment, or repair to

the unit, disconnect the wire to the

spark plug. Remove the spark plug wire to

prevent the engine from starting by acci-

dent

1. Make sure the unit is on a hard flat surface.

2. Check the air pressure in the tyres. If the air

pressure is incorrect, the mower housing will

not cut level. The correct air pressure is

shown on the side of the tyres.

3. (Figure 25) Move the lift lever (1) to the

lowest position (2).

WARNING: The lift lever (3) is

spring loaded. Make sure the lift

lever (1) is locked in the lowest

position (2).

4. (Figure 26) Loosen the left and right ad-

juster knobs (1). Push down on each side of

the mower housing. Make sure both sides of

the mower housing are setting on a flat sur-

face. Also, make sure the lift links (2) are

loose and can easily move up or down.

5. Push down on the adjuster knobs (1) and

the lift links (2). Tighten the left and right

adjuster knobs (1). Make sure the adjuster

knobs (1) are tight. If necessary, use a

wrench to tighten the adjuster knobs (1).

Tighten to a torque of 13,5 N-m.

6. (Figure 25) Raise the lift lever (1).

7. Mow for a short distance. If the height of cut

is not level, repeat the above steps.

Where To Lubricate (Figure 27)

Lubricate the areas shown

with engine oil.

Apply grease with a brush to

the areas shown.

Models with grease fittings:

Lubricate with grease gun.

NOTE: Apply grease to the steering gear as-

sembly.

CAUTION: If the unit is operated in dry areas

that have sand, use a dry graphite spray to

lubricate the unit.

Check The Tyres

Check the air pressure in the tyres. Tyres with

too much air pressure will cause the unit to ride

rough. Also, the wrong air pressure will keep the

mower housing from cutting level. The correct

air pressure is shown on the side of the tyres.

How To Replace The Motion Drive Belt

1. Remove the mower housing. See the instruc-

tions on “How To Remove The Mower Hous-

ing”.

2. Completely push the pedal forward and en-

gage the parking brake.

3. (Figure 28) Remove the idler pulley (1).

4. (Figure 29) To access the belt guides (1),

remove the battery and battery tray. See

“How To Remove The Battery”.

5. Loosen the belt guides (1) at the drive

pulley (2).

6. (Figure 28) Remove the motion drive belt

(3) from the drive pulley (4).

7. (Figure 30) Remove the adjuster nut (2)

from the shifter bracket (3). Pull the motion

drive belt over the shifter bracket (3).

8. (Figure 31) To remove the motion drive belt

(1) from the stack pulley (2), pull the front

end of the belt under the stack pulley (2)

and then back between the stack pulley and

the steering plate (3).

9. (Figure 32) Remove the access panel (1).

10.Remove the two screws (4) that attach the

steering shaft assembly (2). Raise the

steering wheel and steering shaft assembly

(2). Pull the motion drive belt (3) under the

steering shaft assembly (2).

11. Remove the motion drive belt. A correct re-

placement part or assistance is available

from an Authorized Service Centre in your

area.

12.To install the motion drive belt, reverse the

above steps.

13.(Figure 33) Check the routing of the motion

drive belt (1). Make sure the motion drive

belt is installed correctly on the idler pulley

(2). Make sure the steering shaft assembly

(3) is inside the motion drive belt (1).

How To Replace The Mower Drive Belt

(Figure 22)

1. Remove the mower housing. See the instruc-

tions on “How To Remove The Mower Hous-

ing”.

2. Pull the belt retainer (1) away from the idler

pulley (2) and remove the mower drive belt

(3).

3. Pull the belt guide (4) and the brake as-

sembly (7) away from the mandrel pulley

(5) and remove the mower drive belt (3). A

correct replacement part or assistance is

available from an Authorized Service Centre

in your area.

4. To install the mower drive belt, reverse the

above steps.

5. Before you mow, check the blade rotation

control. See the instructions on “How to Ad-

just The Blade Rotation Control”.

How To Remove The Mower Housing

(Figure 36)

1. Move the blade rotation control (1) to the

DISENGAGE position.

2. Move the lift lever (2) to the lowest position.

F-050732L

WARNING: The lift lever (2) is

spring loaded. Make sure the lift

lever (2) is locked in the lowest

position.

3. Remove the hair pins and the washers from

the adjuster arms (3). See illustrations “C”

and “D”.

4. Remove the hair pins and washers from the

suspension links (4). See illustrations “A”

and “B”.

5. Disconnect the extension spring (5) from

the blade control rod (6). See illustration

“E”.

6. Disconnect the front hanger (9) from the

axle support. See illustration “F”.

7. Remove the mower drive belt (7) from the

stack pulley (8). See illustration “G”.

8. (Figure 16) Disconnect the rubber strap (1)

from the connector tube (3). Slide the con-

nector tube (3) off the extension tube (8).

9. Pull the mower housing away from the right

side of the unit.

10.To install the mower housing, reverse the

above steps.

How To Replace The Fuse

If the fuse is blown, the engine will not start.

Remove the fuse and replace with a 15 amp.

automotive fuse.

Storage (over 30 days)

At the end of each year, prepare the unit for

storage as follows.

1. Drain the fuel from the carburettor and the

fuel tank. Change the engine oil. See the en-

gine manufacturer’s instructions.

2. Clean the unit.

3. Charge the battery. See “How To Charge The

Battery”.

How To Order Replacement Parts

The replacement parts are shown either on the

back pages of this Instruction Book or in a

separate Parts List Book.

Use only manufacturer’s authorized or approved

replacement parts. The letter placed on the end

of the part number denotes the type of finish for

the part, C for chrome, Z for zinc, a PA for

purchased assembly. It is important that you

include this when ordering a part. Do not use

attachments or accessories not specifically

recommended for this unit. In order to obtain

proper replacement parts you must supply the

model number of your mower (see nameplate).

Replacement parts are available from your local

Hayter authorised dealer.

If you are unable to obtain parts or service in the

manner outlined above, then contact:

HAYTER LIMITED, Service Department,

Spellbrook, Bishop’s Stortford,

Hertfordshire. CM23 4BU.

UK ONLY: Details of your local Hayter

authorised dealer are contained in Yellow Pages

or contact: Freephone 0800 616298.

When ordering the following information is

required:

(1) The Model Number

(2) Serial Number

(3) Part Number

(4) Quantity

F-050732L

TROUBLE SHOOTING CHART

PROBLEM: The engine will not start.

1. Follow the steps, “How To Start The Engine”

in this book.

2. Electric-Start Models: Clean the battery ter-

minals. Tighten the cables.

3. Check for a loose wire. Tighten the limit

switches. (See the wiring diagram.)

4. Drain the fuel tank. Clean the fuel line. Re-

place the fuel filter.

5. Remove the spark plug(s). Move the throttle

to the SLOW position. Turn the ignition key to

the ON position. Try to start the engine sev-

eral times. Install the spark plug.

6. Replace the spark plug.

7. Adjust the carburettor.

PROBLEM: The engine will not turn

over.

1. Follow the steps, “How To Start The Engine”

in this book.

2. Electric-Start Models: Charge the battery.

3. Replace the fuse.

4. Check the wiring harness for damage or a

loose connection. Repair the damaged wire.

5. Electric-Start Models: replace the solenoid.

Recoil-Start Models: replace the module.

PROBLEM: The engine is difficult to

start.

1. Adjust the carburettor.

2. Replace the spark plug.

3. Replace the fuel filter.

PROBLEM: The engine does not run

smooth or has a loss of power.

1. Check the oil.

2. Clean the air filter.

3. Clean the air screen.

4. Replace the spark plug.

5. The engine is working too hard. Use a lower

gear.

6. Adjust the carburettor.

7. Replace the fuel filter.

PROBLEM: The engine does not run

smooth at fast speed.

1. Replace the spark plug.

2. Adjust the throttle control.

3. Clean the air filter.

4. Replace the fuel filter.

PROBLEM: The engine stops when the

blades are engaged.

1. Check the wiring harness for damage or a

loose connection. Repair the damaged wire.

2. Grass bag must be installed (applies only to

model with rear discharge grass bag).

PROBLEM: On slopes, the engine

stops.

1. Mow up and down slopes. Never mow

across a slope.

PROBLEM: The engine will not idle.

1. Replace the spark plug.

2. Clean the air filter.

3. Adjust the carburettor.

4. Adjust the throttle control.

5. Drain the fuel tank. Clean the fuel line. Re-

place the fuel filter.

PROBLEM: A hot engine causes a de-

crease in power.

1. Clean the air screen.

2. Check the oil.

3. Adjust the carburettor.

4. Replace the fuel filter.

PROBLEM: Excessive vibration.

1. Replace the blade.

2. Check for loose engine bolts.

3. Decrease the air pressure in the tyres.

4. Adjust the carburettor.

5. Check for a damaged belt or damaged

pulley. Replace the damaged parts.

PROBLEM: The grass does not dis-

charge correctly.

1. Stop the engine. Clean the mower housing.

2. Raise the height of cut.

3. Replace or sharpen the blade(s).

4. Move the shift lever to a slower speed.

5. Move the throttle control to the FAST posi-

tion.

6. Replace the spring for the blade idler.

7. Clean the extension tube and the connector

tube (applies only to model with rear dis-

charge grass bag).

PROBLEM: The mower housing does

not cut level.

1. Check the air pressure in the tyres.

2. Adjust the level of the mower housing.

3. Check the front axle. If the front axle does

not freely pivot, loosen the axle bolt(s).

PROBLEM: The mower blades will not

rotate.

1. Check the mower drive belt. Make sure the

belt is installed correctly.

2. Replace the mower drive belt.

PROBLEM: The unit will not move when

the clutch is engaged.

1. Check the motion drive belt. Make sure the

belt is installed correctly.

2. Adjust the clutch.

3. Replace the motion drive belt.

PROBLEM: The unit moves slower or

stops when the clutch is engaged.

1. Adjust the clutch.

2. Replace the motion drive belt.

PROBLEM: When the clutch/brake

pedal is released, belt noise can be

heard.

1. Temporary belt noise does not change the

operation of the unit. If belt noise is continu-

ous, check the routing of the belt. Make sure

the belt is inside all belt guides.

2. If the noise is continuous, adjust the clutch.

PROBLEM: The rear wheels spin over

uneven terrain.

1. Check the front axle. If the front axle does

not freely pivot, loosen the axle bolt(s).

PROBLEM: The transaxle is difficult to

shift between gears with the engine run-

ning and the clutch depressed.

1. Check the clutch adjustment to make sure

the belt stops when the clutch pedal is de-

pressed with the transaxle in (N) neutral.

2. Check the belt guides around the transaxle

drive pulley. Make sure the belt guides do not

touch the pulley.

REPAIR PARTSCODE131C

F-050732L

CHASSIS & HOOD

16 39

REPAIR PARTSCODE131C

F-050732L

CHASSIS & HOOD

Key

No. Part No. Description Key

No. Part No. Description

1 MU1001028 Seat

2 MU028x23 Cap, Push 0n

3 MU094057 Spring

4 MU26x229 Screw

5 MU1001054 Bolt, Wing

6 MU017x47 Washer

7 MU009x56 Bolt, Shoulder

8 MU094154E701 Support, Seat

9 MU094156 Z Rod, Pivot

10 MU1001648E701 Bracket, Pivot

11 MU001x45 Bolt

12 MU015x89 Nut

13 MU009x55 Bolt, Shoulder

14 MU094155 Z Washer

15 MU164x31 Spring

16 MU26x249 Screw

17 MU26x263 Screw

18 MU164x30 Spring

19 MU1001987E549 Deck, Seat

20 MU15x123 Nut

21 MU094151E701 Plate, Index

22 MU009x49 Screw

23 MU1001582 Mat, Left

24 MU1001578 Mat, Right

25 MU1001538E549 Hood

26 MU1001531E549 Grille

27 MU1001546 Lens, Left

28 MU1001544 Housing, Left Headlamp

29 MU1001545 Lens, Right

30 MU1001543 Housing, Right Headlamp

31 MU26x270 Screw

32 MU26x238 Screw

33 MU1001491 Bearing, Steering

34 MU1001584E701 Dash

35 MU26x201 Screw

36 MU093007E701 Panel, Access

37 MU095318E701 Support, Dash

38 MU1001270E701 Bracket, Rear Hanger

39 MU094085E701 Support, Left Grille

40 MU094007E701 Axle, Hanger

41 MU094084E701 Support, Right Grille

42 MU009x58 Bolt, Shoulder

43 MU1001928E701 Frame, Right

44 MU1001927E701 Frame, Left

45 MU690424 Container, Battery

46 MU1001002E701 Plate, Hitch

47 MU690434E701 Panel, Rear

48 MU690482E701 Support, Battery

49 MU26x277 Screw

50 MU015x81 Nut

51 MU15x124 Nut

53 MU1001540 Insert, Grille

55 MU0193x1 Fastener, Panel

57 MU1001652 Trim, Hood (3.75”)

58 MU1001653 Trim, Hood (6.5”)

59 MU1001755 Grommet, Parking Brake

70 MU1001542 Holder, Cup

71 131006 Decal, Left Hood

72 131007 Decal, Right Hood

73 MU48x4032 Decal, Warning

74 MU48x5451 Decal, Shifter

-- MU1001865 Bag, Parts (see Figure 39)

-- 131010 Instruction Book & Parts List

REPAIR PARTSCODE131C

F-050732L

MOTION DRIVE

1234

23 25

REPAIR PARTSCODE131C

F-050732L

MOTION DRIVE

Key

No. Part No. Description Key

No. Part No. Description

1 MU009x39 Bolt, Shoulder

2 MU015x89 Nut, Hex

3 MU690173 Z Arm, Idler

4 MU094041 Z Rod, Clutch

5 MU015x79 Nut

6 MU17x102 Washer

7 MU092697 Grip

8 MU030x20 Pin, Cotter

9 MU094043 Z Lever, Shift

10 MU017x47 Z Washer

11 MU094044 Z Link, Shift

12 MU021920 Z Nut, Adjuster

13 MU091079 Grip

14 MU1001245 Z Rod, Parking Brake

15 MU094815 Z Nut, Adjuster

16 MU1001303 Z Bracket, Shift Pivot

17 MU26x249 Screw

18 MU015x84 Nut

19 MU094042 Z Mount, Stud Spring

20 MU009x54 Bolt, Shoulder

21 MU165x116 Spring, Extension

22 MU1001978E701 Bracket, Right Shifter

23 MU1001928E701 Frame, Right

24 MU002x53 Bolt, Carriage

25 MU1001927E701 Frame, Left

26 MU094045 Z Latch, Parking Brake

27 MU021544 Pedal

28 MU94038E700 Lever, Brake/Clutch

29 MU015x98 Nut

30 MU037x87 Belt, Motion Drive

31 MU094031 Z Yoke, Shift

32 MU0031x6 Pin, Hair

33 MU017x38 Washer

34 MU690369 Spacer

35 MU06x105 Bolt

36 --- ** --- Transaxle, Peerless

37 MU015x88 Nut

38 MU020697 Key, Woodruff

39 MU01x155 Bolt

40 MU094008E701 Bracket, Transaxle

41 MU690409 Pulley

42 MU094433E701 Bracket, Transaxle Support

43 MU0011x7 Ring, Snap

44 MU095094 Pulley, Drive

45 MU021553 Key, Square

46 MU17x160 Washer

47 MU690554 Z Spacer, Transaxle

48 MU024373 Stem, Valve

49 Tire *

-- MU407049 Tube

50 MU690376-601 Wheel & Tire Assembly

51 MU17x195 Washer

52 MU0011x3 E-Ring

53 MU094618 Hub Cap

54 MU093349 Guide, Belt

55 MU0031x4 Pin, Hair

56 MU165x141 Spring, Extension

57 MU165x92 Spring, Extension

58 MU26x216 Screw

59 MU17x148 Washer

60 MU26x267 Screw

61 MU17x169 Washer

* When you order a tire, make sure to give the brand name of the tire so that the tread pattern on the tire will match.

** For information on Replacement Parts for this transaxle contact the manufacturer.

REPAIR PARTSCODE131C

F-050732L

STEERING

REPAIR PARTSCODE131C

F-050732L

STEERING

Key

No. Part No. Description Key

No. Part No. Description

1 MU095185 Wheel, Steering

2 MU690625 Post, Steering

3 MU711326 Insert, Steering Wheel

4 MU094124 Bearing, Lower

5 MU15x111 Nut, Flange

6 MU009x57 Bolt, Shoulder

7 MU1001893 Gear, Pinion

8 MU011x25 Ring, Snap

9 MU094121 Gear, Sector

10 MU094123 Bearing

11 MU001x84 Bolt

12 MU1001121E701 Plate, Steering

13 MU094006E701 Plate, Engine

14 MU015x88 Nut, Flange

15 MU15x118 Nut, Flange

16 MU1001270E701 Bracket, Hanger

17 MU094007E701 Axle, Hanger

18 MU01x146 Bolt

19 MU030x49 Pin, Cotter

20 MU690150 Bearing

21 MU1001299E701 Spindle Assembly, Left

22 MU01x111 Bolt

23 MU17x104 Washer

24 MU017x53 Z Washer

25 MU015x84 Nut, Flange

26 MU690210E701 Axle Assembly

27 MU095329E701 Drag Link, Left

28 MU1001298E701 Spindle Assembly, Right

29 MU095328E701 Drag Link, Right

30 MU26x249 Screw

31 MU091334 Bearing, Wheel

32 MU024373 Stem, Valve

33 Tire *

-- MU407046 Tube

34 MU690377-601 Wheel and Tire Assembly

35 MU17x195 Washer

36 MU17x192 Washer

37 MU017x83 Washer

38 MU094618 Hub Cap

39 MU26x267 Screw

40 MU092059 Bellows

41 MU0025x3 Bolt

42 MU17x146 Washer

* When you order a tire, make sure to give the brand name of the tire so that the tread pattern on the tire will match.

REPAIR PARTSCODE131C

F-050732L

MOWER HOUSING SUSPENSION

910

18 19

24 24

REPAIR PARTSCODE131C

F-050732L

MOWER HOUSING SUSPENSION

Key

No. Part No. Description Key

No. Part No. Description

1 MU092698 Grip

2 MU094157 Z Handle, PTO

3 MU094022 Z Pad, Switch

4 MU0025x3 Bolt

5 MU092697 Grip

6 MU166x40 Spring

7 MU17x103 Washer

8 MU690533 Handle, Lift

9 MU094017 Z Lever, PTO

10 MU009x39 Bolt, Shoulder

11 MU030x20 Pin, Cotter

12 MU017x57 Washer

13 MU094004 Z Link, PTO

14 MU015x84 Nut, Flange

15 MU26x249 Screw

16 MU166x39 Spring

17 MU094018E701 Bracket, PTO

18 MU165x116 Spring

19 MU690394E701 Crank, PTO

20 MU094053E701 Link, Lift

21 MU094028 Z Link, Lift Handle

22 MU15x118 Nut, Flange

23 MU17x57 Washer

24 MU0031x4 Pin, Hair

25 MU017x91 Washer

26 MU001x74 Bolt, Hex

27 MU690386E700 Arm Assembly, Right Lift

28 MU094180E700 Arm, Right Lift

29 MU094030E700 Plate, Lift Arm

30 MU094067 Pin

31 MU094055E701 Bracket, Rear Suspension

32 MU094065 Bushing, Lift Tube

33 MU009x53 Bolt, Shoulder

34 MU094015E700 Bracket, Pivot

36 MU17x191 Washer

37 MU015x84 Nut, Flange

38 MU165x117 Spring

39 MU015x68 Nut, Flange

40 MU094005E700 Bracket, PTO

41 MU094026E700 Hanger, Right Deck

42 MU094027E700 Hanger, Left Deck

43 MU094158 Z Rod, Hanger

44 MU690381E700 Hanger, Front

45 MU015x89 Nut, Flange

46 MU030x49 Pin, Cotter

47 MU690382 Pin, Threaded Shoulder

48 MU26x49 Screw

49 MU01x106 Bolt, Hex

50 MU017x38 Washer

51 MU690370E701 Plate, Weight (4 Required)

REPAIR PARTSCODE131C

F-050732L

MOWER HOUSING

10 11 12

17 18

220

34 34

27 43

37 38

REPAIR PARTSCODE131C

F-050732L

MOWER HOUSING

Key

No. Part No. Description Key

No. Part No. Description

1 MU690432 Pulley

2 MU015x84 Nut, Flange

3 MU15x140 Nut

4 MU037x74 Belt, Blade

5 MU690387 Pulley, Idler

6 MU094129 Mandrel

7 MU025x23 Screw

8 MU092424 Guide, Belt

9 MU094130 Spacer

10 MU094055E701 Bracket, Rear Suspension

11 MU009x52 Bolt, Shoulder

12 MU094068 Knob

13 MU017x45 Washer

14 MU009x51 Bolt, Shoulder

15 MU690379E700 Plate, Suspension

16 MU094137 Pad, Friction

17 MU166x43 Spring

18 MU015x79 Nut, Flange

19 MU690378E700 Bracket, Rear Deck

20 MU095194 Pin, Hanger

21 MU094053 Link, Lift

22 MU15x116 Nut

23 MU690427E700 Bracket, Idler Arm

24 MU1002076 Assembly, Idler Arm & Pad

25 MU26x249 Screw

26 MU009x39 Bolt, Shoulder

27 MU002x64 Bolt, Carriage

28 MU690530E700 Housing, Blade

29 MU690399E700 Baffle

30 MU015x89 Nut, Flange

31 MU054695 Strap, Rubber

32 MU01x139 Screw

33 MU690367 Chute

34 MU015x79 Nut

35 MU165x118 Spring, PTO

36 MU165x140 Spring, Extension

37 MU015x84 Nut, Flange

38 MU690380E700 Bracket, Front Deck

39 MU094067 Pin, Threaded Shoulder

40 MU017x91 Washer

41 MU0031x4 Pin, Hair

42 MU1002067E700 Hanger, Front

43 MU1401275 Housing, Jackshaft

44 MU690359 Fan, Assist

45 MU1001237E701 Housing, Fan

46 MU017x37 Washer

47 MU001x71 Bolt

48 MU001x106 Bolt

49 MU15x100 Nut

50 MU17x165 Washer

51 MU17x166 Washer, Belleville

52 MU1002068E701 Blade

53 MU092466 Adapter, Blade

54 MU01x121 Bolt

55 MU015x98 Nut, Flange

56 MU690369 Spacer

57 MU1001952E701 Plate, Jackshaft Support

1-57 MU776110 Blade Housing, Complete

REPAIR PARTSCODE131C

F-050732L

ENGINE MOUNT

15 15

REPAIR PARTSCODE131C

F-050732L

ENGINE MOUNT

Key

No. Part No. Description Key

No. Part No. Description

1 MU092317 Fuel Cap **

2 MU690280 Fuel Tank

3 MU095197 Hose Clamp **

4 MU7601033 Fuel Line (Cut to length) **

5 MU095197 Hose Clamp **

6 MU26x201 Screw

7 MU094006E701 Plate, Engine

8 MU092371 Throttle Control

9 --- * --- Engine, Briggs & Stratton

10 MU0025x7 Bolt, Engine Mount

11 MU690439 Stack Pulley Assembly

12 MU019x35 Lockwasher

13 MU01x140 Bolt, Hex

14 MU17x170 Washer

15 MU26x249 Screw

16 MU26x229 Screw

17 MU690538E701 Bracket, Muffler

18 MU26x277 Screw

19 MU690537E701 Bracket, Muffler Mount

20 MU026x214 Screw

21 MU094384 Guide, Belt

22 MU015x79 Z Nut, Flange

23 MU094066 Guide, Belt

24 MU1001620-701 Guard, Heat Shield

25 MU1001747 Exhaust Tube, Single

30 MU1001619-701 Shield, Heat

31 MUMU094654 Muffler

32 MU091309 Gasket

33 MU06x103 Screw

34 MU018x15 Washer

35 MU06x104 Bolt, Washer Hex Head

36 MU1001880 Guard, Exhaust Pipe

37 MU1002080 Valve, Fuel Shut-Off

* For information on Replacement Parts for this engine contact the manufacturer.

** These parts are included with Key No. 2

REPAIR PARTSCODE131C

F-050732L

ELECTRICAL SYSTEM

24x32

94159

24x31

92377

94613

REAR HARNESS: 250X130

LIGHT HARNESS: 250X92

MAIN HARNESS: 250X126

094136

1001575

21075

1001845

REPAIR PARTSCODE131C

F-050732L

ELECTRICAL SYSTEM

Key

No. Part No. Description

1 MU250x92 Harness, Light Wire

MU1001716 Socket, Light

MU090084 Bulb, Light

2 MU250x126 Harness, Chassis Wire

3 MU092377 Switch, Ignition

MU020729 Key, Ignition

MU091489 Nut, Hex

MU091488 Cap, Ignition

4 MU1001575 Switch, Limit

5 MU302031 Fuse

MU407078 Holder, Fuse

6 MU1002004 Solenoid

MU26x229 Screw, Mounting

MU15x116 Locknut

7 MU024x32 Cable, Battery Ground

MU26x229 Screw, Ground Cable

8 MU021075 Battery

MU002x82 Bolt, Carriage

MU014x79 Wingnut

MU690604 Boot, Battery -Positive (RED)

9 MU250x130 Harness, Seat Switch Wire

10 MU094159 Switch, Seat Sensor

11 MU024x31 Cable

12 MU1001845 Switch, Bag Sensor

13 MU094136 Switch, Limit

REPAIR PARTSCODE131C

F-050732L

GRASS BAGGER

10 11

14 19

27 26

REPAIR PARTSCODE131C

F-050732L

GRASS BAGGER

Key

No. Part No. Description Key

No. Part No. Description

1 MU690404 Tube, Top

2 MU01x121 Bolt

3 MU15x116 Nut

4 MU690433 Strut, Bag

5 MU015x79 Nut, Flange

6 MU0193x2 Fastener, Panel

7 MU690491 Seal, Bag (Right End)

8 MU690492 Seal, Bag (Center)

9 MU690493 Seal, Bag (Left End)

10 MU690356E700 Hinge

11 MU26x249 Screw

12 MU690403 Assembly, Bag Frame

13 MU690400E700 Bracket, Switch

14 MU002x82 Bolt, Carriage

15 MU015x89 Nut, Flange

16 MU17x185 Washer

17 MU690402 Latch, Spring

18 MU690362E701 Pan, Rear

19 MU002x53 Bolt, Carriage

20 MU690355E700 Bracket, Bagger Mounting

22 MU1001000E701 Plate, Hitch

23 MU1001001E701 Bracket, Lower Mounting

24 MU1001002E701 Plate, Hitch

26 MU054563 Pin, Latch

27 MU002x39 Bolt, Carriage

28 MU690368 Tube, Connecting

29 MU690429 Grommet, Extension Tube

30 MU690438 Bag, Grass

F-050732L

rev. 2 M16006.25.02

DEG-Konformitätserklärung

GB EC Certificate of Conformity

FDéclaration de conformité pour la CEE

ICertificato di conformita’ comunitario

EDeclaración de Conformidad

NL EG-Conformiteitsverklaring

SEU-konformitetsintyg

NEU-konformitetserklæring

DK EU-overensstemmelseserklæring

SF EY: n Vaatimustenmukaisuusilmoitus

PDeclaração de conformidade

conforming to Directive 98/37/EC

conforming to Directive 89/336/EEC

conforming to Directive 2000/14/EC

entsprechend der Richtlinie 98/37/EG

entsprechend der Richtlinie 89/336/EWG

entsprechend der Richtlinie 2000/14/EG

conforme à la directive 98/37/CE

conforme à la directive 89/336/CEE

conforme à la directive 2000/14/CE

conforme alla Direttiva 98/37/CE

conforme alla Direttiva 89/336/CEE

conforme alla Direttiva 2000/14/CE

según la directiva 98/37/CE

según la directiva 89/336/CEE

según la directiva 2000/14/CE

overeen komstig de Richtlijn 98/37/EG

overeen komstig de Richtlijn 89/336/EEG

overeen komstig de Richtlijn 2000/14/EG

conforme com a Diretiva 98/37/CE

conforme com a Diretiva 89/336/CEE

conforme com a Diretiva 2000/14/CE

överensstämmande med direktiv 98/37/EG

överensstämmande med direktiv 89/336/EEG

överensstämmande med direktiv 2000/14/EG

overholder direktiv 98/37/EF

overholder direktiv 89/336/EØS

overholder direktiv 2000/14/EF

overholder direktiv 98/37/EF

overholder direktiv 89/336/EØF

overholder direktiv 2000/14/EF

naudattaa direktiiviä 98/37/EY

naudattaa direktiiviä 89/336/ETY

naudattaa direktiiviä 2000/14/EY

F-050732L

rev. 2 M16006.25.02

MURRAY, INC.

219 FRANKLIN ROAD, BRENTWOOD, TN USA 37027

erklären in alleiniger Verantwortung, daß das Produkt

declare in sole responsibility, that the product

déclarons sous notre seule responsabilité que le produit

dichiariamo sotto la nostra piena responsabilità che il prodotto

declaramos bajo responsabilidad propia que el producto

verklaren enig in verantwoording, dat het produkt

declaramos com responsabilidade própria que o produto

intygar med ensamansvar att nedanstående produkt

erklærer som eneansvarlig at produktet

erklærer som eneansvarlig, at produktet

ilmoitamme yksin vastaavamme, että tuote

(Fabrikat, Typ) (Make, model) (Marque, modèle) (Marca, tipo)

(Marca, modelo) (Fabricant, type) (Marca, modelo) (Fabrikat, typ)

(Fabrikat, type) (Mærke, type) (Merkki, malli)

Wir / We / Nous / Noi / Nosotros / Wij / Nós / Vi / Vi / Vi / Me

312002x11B

auf das sich diese Erklärung bezieht, den Anforderungen der Richtlinie 98/37/EG, der Richtlinie 2000/14/EG

(Konformitätsbewertungsverfahren gemäß Anhang VIII) Richtlini 2002/88/EC und der Richtlinie 89/336/EWG und aktuellen

Ergänzungen entspricht

to which this certificate applies, conforms to the requirements of Directive 98/37/EC , Directive 2000/14/EC (conformity assessment

procedure according to Annex VIII), Directive 2002/88/EC and Directive 89/336/EEC and current amendments

faisant l’objet de la déclaration est conforme aux prescriptions fondamentales stipulées dans la Directive 98/37/CE, la directive

2000/14/CE (procédure d’évaluation de conformité selon l’annexe VIII), directive 2002/88/EC la directive 89/336/CEE etleurs

modifications courantes

cui la presente dichiarazione si riferisce, è conforme ai requisiti della Direttiva 98/37/CE, della Direttiva 2000/14/CE (procedura di

valutazione della conformità secondo l’Allegato VIII), Direttiva 2002/88/EC e della Direttiva 89/336/CEE e correnti emendamenti

al cual se refiere la presente declaración corresponde a las exigencias de la directiva 98/37/CE, de la directiva 2000/14/CE (los

procedimientos de evaluación de conformidad según el Anexo VIII) directiva 2002/88/EC y de la directiva 89/336/CEE y enmiendas

vigentes

waarop deze verklaring betrekking heeft, overeenkomt met eisen van de richtlijn 98/37/EG, de richtlijn 2000/14/EG

(conformiteitsbeoordelingsprocedure volgens bijlage VIII), richtlijn 2002/88/EC de richtlijn 89/336/EEG en huidige wijzigingen

ao que se refere esta declaração corresponde às exigências da Directiva 98/37/CE, Directiva 2000/14/CE (em conformidade com o

processo de avaliação, de acordo com o Anexo VIII) Directiva 2002/88/EC e Directiva 89/336/CEE e actuais alterações

för vilket detta intyg gäller, uppfyller kraven enligt direktiv 98/37/EG, direktiv 2000/14/EG (procedur för bedömning av överensstämmelse

enligt tillägg VIII), direktiv 2002/88/EC, 89/336/EEG samt allmäna tillägg

som denne erklæring vedrører, oppfyller kravene i direktiv 98/37/EF, direktiv 2000/14/EF (konformitetsvurderingsprosedyre i henhold til

anneks VIII) direktiv 2002/88/EC og direktiv 89/336/EØS og aktuelle vedlegg

som denne erklæring vedrører, overholder kravene i direktiv 98/37/EF, direktiv 2000/14/EF (konformitetsvurderingsprocedure iflg. Annex

VIII) direktiv 2002/88/EC og direktiv 89/336/EØF og ændringer

johon tämä ilmoitus liittyy, vastaa direktiivin 98/37/EY, direktiivin 2000/14/EY (Liitteen VIII mukaisten yhdenmukaisuuden

arviointitoimien), direktiivin 2002/88/EC, direktiivin 89/336/ETY ja nykyisten muutosten vaatimuksia

Zursachgerechten Umsetzung der EG-Richtlinien wurde(n) folgende Norm(en) und/oder technische Spezifikation(en) herangezogen:

EN 836/A2:2001, EN 836:1997, BS EN 1033:1996 und/oder BS EN 1032:1997, EN ISO 3744;1995, ISO 11094;1991

To effect correct application of the EEC Directives, the following standards and/or technical specifications were consulted: EN

836/A2:2001, EN 836:1997, BS EN 1033:1996 and/or BS EN 1032:1997, EN ISO 3744;1995, ISO 11094;1991

Pour mettre en pratique les Directives de la CEE, il a été tenu compte de la/des norme(s) et/ou de la/des spécification(s) technique(s)

suivante(s): EN 836/A2:2001, EN 836:1997, BS EN 1033:1996 et/ou BS EN 1032:1997, EN ISO 3744;1995, ISO 11094;1991

Per un’appropriato riscontro della normativa CEE, è (sono) stata(e) consultata(e) la(e) seguente(i) norma(e) e/o specifica(che)

tecnica(che): EN 836/A2:2001, EN 836:1997, BS EN 1033:1996 e/o BS EN 1032:1997, EN ISO 3744;1995, ISO 11094;1991

Con el fin de realizar de forma adecuada las exigencias en las normativas de la CEE (fué(ron) consultada(s) la(s) siguiente(s)

normativa(s) y especificación(es) técnica(s): EN 836/A2:2001, EN 836:1997, BS EN 1033:1996 y/o BS EN 1032:1997, EN ISO

3744;1995, ISO 11094;1991

Om de EG-richtlijnen in juiste vorm om te zetten, is/zijn van volgende norm(en) en/of technische specificatie(s) gebruik gemaakt: EN

836/A2:2001, EN 836:1997, BS EN 1033:1996 en/of BS EN 1032:1997, EN ISO 3744;1995, ISO 11094;1991

Com o fim de realizar de forma apropriada as exigências nas normas da C.E.E. consultou-se a(s) seguinte(s) norma(s) e/ou

especificação(ões) técnica(s): EN 836/A2:2001, EN 836:1997, BS EN 1033:1996 e/ou BS EN 1032:1997, EN ISO 3744;1995, ISO

11094;1991

Följande norm(er) och/eller teknisk(a) specifikation(er) har legat till grund för ett fackmässigt införande av de i EU-normerna: EN

836/A2:2001, EN 836:1997, BS EN 1033:1996 och/eller BS EN 1032:1997, EN ISO 3744;1995, ISO 11094;1991

Følgende normer og/eller tekniske spesifikasjoner er lagt til grunn for gjennomførelse av EU-retningslinjenes: EN 836/A2:2001, EN

836:1997, BS EN 1033:1996 og/eller BS EN 1032:1997, EN ISO 3744;1995, ISO 11094;1991

Til gennemførelse af de EF-direktivet er følgende standard(er) og/eller tekniske specifikation(er) anvendt: EN 836/A2:2001, EN

836:1997, BS EN 1033:1996 og/eller BS EN 1032:1997, EN ISO 3744;1995, ISO 11094;1991

ETY-direktiivien oikean soveltamisen varmistamiseksi on käytetty seuraavia standardeja ja/tai teknisiä erittelyjä: EN 836/A2:2001, EN

836:1997, BS EN 1033:1996 ja/tai BS EN 1032:1997, EN ISO 3744;1995, ISO 11094;1991

F-050732L

rev. 2 M16006.25.02

Bauart

Hayter Mowers 13 30 Users Manual F 050732L

!! Hayter-4 Hayter Lawn Mower Manuals - Lawn Mower Manuals – The Best Lawn Mower Manuals Collection

1330 to the manual 90f24996-1e53-4aa6-9bbe-f351d43e2a7e

Navigation menu

Versions of this User Manual:

Views

Navigation