Hearth and Home Technologies RC100 Remote Control Transmitter User Manual

Hearth & Home Technologies Remote Control Transmitter

User manual

Hearth & Home Technologies • RC100 Wireless Wall Switch • 2166-391 • 6/09 1Installation & Operating InstructionsRC100IntelliFire Plus™ Wireless Wall Switch Hearth & Home Technologies disclaims any responsibility for, and the warranty will be voided by, the following actions:• Installation and use of any damaged system component.• Modicationofthesystemcomponent.• Installation other than as instructed by Hearth & Home Technologies.• Installation and/or use of any component part not approved by Hearth & Home Technologies.Any such action may cause a re hazard.• Read, understand and follow these instructions for safe installation and operation.IntroductionThe RC100 wireless wall switch is designed to turn yourgasreplaceonandoff.TheRC100wirelesswallswitch is only for use with the Hearth & Home Tech-nologies IntelliFire Plus™ system (IPI).FCC RequirementsWARNING! Risk of Fire! Changes or modications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.Installation of Wireless Wall SwitchCAUTION! Risk of Fire! DO NOT install damaged or modied components. Warranty will be voided if damaged or modied components are installed.Kit components: One wireless wall switch, two #6 screws, two wall anchors, two CR2032 batteries.1. Remove wall switch components from packaging.2.Insert small at screwdriver in the tab located in thebottom of the wall switch and twist the screwdriver to disassemble the wall switch. See Figure 1.Figure 1. Wall Switch DisassemblyNote: This equipment has been tested and found to comply with the limits for a Class B digital device, pur-suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in ac-cordance with the instructions, may cause harmful in-terference to radio communications. However, there is no guarantee that interference will not occur in a partic-ular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit dif-ferent from that to which the receiver is connected.• Contact the dealer or an experienced radio TV techni-cian for help.Installation PrecautionsThis wall switch is tested and safe when installed in ac-cordance with this installation manual. Do not install any components that may be damaged. Do not modify, disassemble, or substitute any of the com-ponents included with this kit. Installation of this unit must bedonebyaqualiedservicetechnician.Placement of this wall switch may affect performance. An assessment of the space should be done prior to installa-tion for optimum performance.Determine LocationDetermine the location for the wireless wall switch. The selected location should be in the same space as the gas replacewith visualsightofreplace.Thewireless wallswitchmustbeplacedwithin30feetofthereplacebutshould not be exposed to extreme heat.The RC100 is approved for interior installation and should always be placed under weather resistant cover when used in exterior applications.
Hearth & Home Technologies • RC100 Wireless Wall Switch • 2166-391 • 6/092Figure 4. RC100 Function5. Place the cover back on the wall switch and press the top button. The red light illuminates if the batteries were properly installed. See Figure 4.ONOFFProgramming the RC100 to the Control ModuleCAUTION! Risk of burns! DO NOT program the wireless wall switch to the control module when replace is hot.• Verify the ON/OFF/REMOTE switch is in the REMOTE position. Green LED light will blink twice and wall switch will beep twice. See Figure 5.• Using a small item (such as a paper clip) press and release the learn button located near the ON/OFF/REMOTE switch. See Figure 5.• Control module will beep once and LED will blink green for 10 seconds. • While the LED is blinking, press the top button on the RC100 wall switch. A double beep will come out of the control module to indicate that it has been programmed successfully.NOTICE: Up to three remote controls can be programmed into the control module. Simply press a button on the other remote controls during the 10 second programming process to add another remote into the system.To clear memory in the control module, use a small item (such as a paper clip) to press and release the LEARN button. Control module will beep once and LED will blink green for 10 seconds DO NOT press any buttons on the remote during the ten seconds that the green LED blinks. The memory will be cleared.Turning On the Fireplace• Press the top button to turn the fireplace ON. The replacewillrstignitethepilot.Oncethepilotameisestablished the main burner will be lit. Adjusting Flame HeightTheameheightcanbeadjustedbyslidingtheHI/LOWswitch to the desired setting. See Figure 5. If the HI/LOW switchisintheLOWpositiontheburneramewilladjustto LOW ten seconds after ignition.CAUTION! Risk of burns! Only adjust ame height when replace is cool.Figure 5. Programming RC100REMOTE POSITIONFigure 3. Battery Installation4. Insert the two CR2032 batteries (supplied) into the cir-cular slots with the positive side of batteries facing up. See Figure 2.FLAME HEIGHTFigure 2. Mounting Wireless Wall Switch3.Securethewallswitchonaatwallsurfaceusingthetwo screws and wall anchors provided. See Figure 2. Thisdevicewilltintoastandardsizejunctionbox.
Hearth & Home Technologies • RC100 Wireless Wall Switch • 2166-391 • 6/09 3TO JUNCTION BOX (120V)6V DC SUPPLYRECEIVERISFLAMESENSEORANGE(PILOT)GREEN(MAIN)BROWNGROUNDBLACKREDBROWN/REDOPTIONAL ON/OFF SWITCHBATTERY PACK6V DC (AA X 4)FLAMEMODULATIONRC100 6V DC(CR2032 X 2)(WALL SWITCH)WHITEORANGEFigure 6. RC100 Wiring Diagram
Hearth & Home Technologies • RC100 Wireless Wall Switch • 2166-391 • 6/094Frequently Asked Questions/TroubleshootingPlease contact your Hearth & Home Technologies dealer with any questions or concerns. For the location of your nearest Hearth & Home Technologies dealer, pleasevisitwww.reside.com.Power Outage• IfreplacebatterybackupsystemISinstalledattimeofpoweroutage,replaceoperationwillnotbeinterrupted.• IfreplacebatterybackupsystemISNOTinstalled attimeofpoweroutage,replacewillshutoff.Toresumereplaceoperation,installbatterybackup.Symptom Possible Cause Corrective ActionWall switch will not transmit Batteries Verify batteries are installed with positive side facing up. Verify batteries work properly.Control module will not take commands from wall switchControl module is not in “REMOTE” mode Ensure module switch is set to REMOTE.Control module and wall switch are not programmed to each otherThe control module will beep when it successfully re-ceives a command. If it does not beep, clear module memory and reprogram wall switch.Control module is unplugged. In case of power outage, backup batteries are depleted or missingIf red LED light comes on when top button is pressed, verifythatthecontrolmoduleispluggedinthereplacejunctionboxlocatedinthecontrolsarea.Alsoverifythatthe batteries are installed in the battery pack.Fireplace shuts down after extended periods Built-in timer The replace will automatically shut down after ninehours of continuous operation in REMOTE mode. Fireplace is on but will not shut off with the remote controlExternal wired wall switchThereplacecannotbeturnedoffbyremoteifanexter-nal wired wall switch is installed and in the ON position. Turn external wall switch to OFF.Control module failureAt control module, turn off replace by sliding the ON/OFF/REMOTE switch to OFF. Warning! Risk of Burns! Fireplace is hot. Use caution when accessing module.WARNING! Risk of burns! In the event of a wall switch malfunction, DO NOT attempt to turn off the replace manually using the control module. The decorative front will be hot and severe burns may occur. Call you dealer for assistance.Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

Navigation menu