HeathCo 12WDB10TX Wireless Doorbell Transmitter User Manual 60

Download:
Mirror Download [FCC.gov]
Document ID	246865
Application ID	YfkfOJmuw/ygx4dDI3Gq5A==
Document Description	users manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	22.62kB (282803 bits)
Date Submitted	2002-06-04 00:00:00
Date Available	2002-06-03 00:00:00
Creation Date	2002-05-09 16:49:49
Producing Software	Acrobat PDFWriter 4.0 for Windows
Document Lastmod	0000-00-00 00:00:00
Document Title	(60)
Document Creator	May 9, 2002 (60)
Document Author:	cee3

Say What?!” Wireless Chime
This package includes (Style of pushbutton and chime may vary from illus-
tration):
. Wireless chime 0 Wireless pushbutton with demostration batteries
- Hardware pack 0 Door hanger
- Audio cable (7 Jumper Model Only)
You'll need to buy 3 "C" alkaline batteries for the chime. In typical use.
alkaline batteries will last up to one year.
1 . Install 4 type "AA" alkaline batteries. Open
back of case by removing screw at top of
battery nnver with small philips-head screw-
driver. Slide cover up and remove. Insert
batteries according to markings inside
pushbutton. Reverse above proceedures to
reattach battery cover.
2. Open chime case. Open back of case by
removing 2 sorews at top of battery cover with
small pnilips-head screwdriver. Press in catch
on bottom of chime and remove cover.
3.|nstall 3 type "C" alkaline batteries. In-
3 Jumper Model Shown sert batteries according to markings inside
. the chime. Reverse above proceedures to
attach battery cover.
Z 4. Test functions. Temporarily position chime
‘ and pushbutton where you want them
mounted. Press pushbutton to verify chime
and pushbutton work properly. If chime does
not sound, see Troubleshooting.
. Adlust volume. The chime is equipped with
a HigNLow switch located on the left side.
Slide the switch to either High or Low to ad-
just volume.
Q 9002 DESA International 598-1126-00
6. Mount pushbutton and chime.
Use either screw, door hanger, or double sided tape to mount pushbutton.
To mount with screw, determine where pushbutton will be located. Using 3/16" drill
bit, drill tap hole. if screw is not mounted directly into wood stud or trim molding,
use drywall anchor. insert screw leaving approximately 1/ " gap between head of
screw and wall. Place keyhole slot on rear of pushbutton over the screw’s head
and slide down firmly.
When attachlng pushbutton uslng door hanger, place keyhole slot on rear of
pushbutton over stud on door hanger and slide down firmly. Hang door hanger
on door handle.
When attaching pushbutton using double sided tape, make sure the surface
of the door jamb or wall is clean.
Chime can be mounted by using 1 screw with keyhole (see illustration on
page 1). Follow steps under mounting pushbutton with screw to mount chime.
Code and Tune Settings
Code Settings
Note: Most installations will not require you to change any jumpers on
your chime and pushbutton.
This manual includes operating instructions for different types of chimes. All
chimes work on the same principle and use the same channel setting infor-
mation. Please read all instructional information and note any specific infor—
mation pertaining to your particular chime.
The pushbutton and chime communicate by using e node that can he changed
by removing and/or addingjumpers on both the pushbutton and chime. The
code is factory set; however, there are selectable codes that allow you to
expand your system and prevent outsme interterence (3 Jumper Models-8
selectable codes; 7 JumperaModeIs-t 28 selectable codes). Other wireless
products may cause interference and the system may not function properly.
Follow the instructions below for setting a new code.
1. To access the jumpers, remove the battery covers and locate the jumpers
on both the pushbutton and chime (See illustration on page 3). Note: To
access the jumpers on the pushbutton, the batteries must be removed.
2. The pushbutton and chime both have multiple jumpers (either 3 or 7 de-
pending on model). The jumpers are used for setting the code.
3. To change the code, add and/or remove jumpers as needed. It is recom-
mended to only change one jumper at a time and then check to see If
system is functioning properly. Note: Jumpers must be exactly the same
for both the pushbutton and chime for this system tn function,
-2. 598-1 126-00
ChimeTune Settings
Your wireless chime has different selectable tune modes: 4 prerecorded
sounds and 1 setting that cycles through the 4 prerecorded sounds (the 7
jumper model adds the ability to record up to 10 seconds of audio via the
audio cable or built-in microphone).
To select different tune modes, slide switch located on right side of chime to
numbers I through 410 select the prerecorded sound desired. Select "All" to
allow chime to cycle through the 4 prerecorded sounds each time the chime
sounds.
7 Jumper Model: To record up to 10 seconds of audio using the audio cable,
plug one end of the audio cable into the 3 ‘/2 mm headphone or audio out jack
on your sound source. Plug other end of audio cable into 3 '/2 mm audio jack
located on back of chime near the top. Slide tune setting switch to position
number 5 Push down and hold “Rec” huttnn (located near audio jack) while.
playing audio from your sound source. Release ‘JRec” button when completed.
To record up to 10 seconds of audio using built-in microphone, press down
and hold the “Rec” button located on the back of the pushbutton near the
bottom while speaking or playing the audio from your sound source. Release
the “Rec” button when completed. Note: The microphone is located on front of
chime. For best results, do not hold the microphone closer than 2" to the sound
source.
Recording Pushbutton Audio
Your pushbutton has the capability to record up to 10 seconds of audio for
personalized messages andfsounds.
To record up to 10 seconds of audio, press down and hold “Rec" button Io-
natert on hank of pushbutton near bottom while speaking or playing audio from
your sound source. Release fflilec" button when completed. Note: The micro-
phone is Iocated on front of pUShbutton. For best results, do not hold the mi-
crophone closer than 2" to‘flhe sound source.
7 Jumper Model: To record 'up to 10 seconds of audio, plug one end of the
audio cable into the 3 1/2 mm headphone or audio out jack on your sound
source. Plug other end of audio cable into 3 1la mrn audio jack located on
back of pushbutton near the bottom. Push down and hold “Rec” button (lo-
cated near audio jack) while playing audio from your sound source. Release
“Rec” button when completed.
598-1126—00 .3.
Troubleshooting
Chime doesn't sound:
. Make sure pushbutton and chime codes are the same (See pages 2 and 3).
0 Check orientation of pushbutton and chime batteries (See markings in-
side pushbutton and chime).
- Check charge of pushbutton and chime batteries. replace if necessarv.
. Verity pushbutton and chime are within 50 feet of each other.
Batteries seem OK, but the chime doesn't work when installed:
0 Don't mount chime or pushbutton on metal or near metal studs. This re-
duces the transmitter range. Use 1/ “ to 1/ " (6 to 13 mm) wood shims to
move chime or pushbutton off metal surface.
- Concrete floors may reduce range. Move chime away from floor.
0 Try locating chime closer to pushbutton.
The range of the wireless chime can vary with location, temperature and
battery condition.
Regulatory Information
This device (12OORX, 1201RX, 1204RX, 1210TX, 1214TX) complies with
Part 15 of the FCC Rules. Operation is subject to the following two condi-
tions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause
undesired operation.
The user is cautioned that changes or modifications not expressly approved
by the party responsible for regulatory compliance could void the user’s au-
thority to operate the equipment.
This product complies with ASTM F963-96a.
Age grading information: ’ . ’
- 3 Jumper Model - “Ages 5'&,—Up”
- 7 Jumper Model - “Ages 14- & Up"
Do not send products,fplease call the number listed below:
Technical Service: USA can 1-800-858-8501/Canada call 905-826-8010
or visit our Web site at: www.desatech.com.
DESA International, Inc.
PO. Box 90004, Bowling Green, KY 42102-9004
_4. 598-1 126-00
YOUR ONE YEAR LIMITED WARRANTY
This is a "Limited Warranty" which gives you specific legal fights. You may
also have other rights which varytrom state to state or province to province.
For a period of one year from the date of purchase, any malfunction
caused by factory defective parts or workmanship will be corrected at no
charge to you. Batteries are not covered. To obtain a refund or a
replacement, return the product to the place of purchase.
Not Covered - Repair service, adjustment and calibration due to misuse,
abuse or negligence, light bulbs and other expendable items are not
covered by this warranty. Unauthorized service or modification of the
product or of any furnished component will void this warranty in its entirety.
This warranty does not include reimbursement for inconvenience, installa-
tion, setup time, loss of use, or unauthorized service.
This warranty covers only DESA international, Inc. assembled products
and is not extended to other equipment and components that a customer
uses in conjunction with our products.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRAN-
TIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY,
REPRESENTATION OR CONDITION §OF MERCHANT ABILITY OR
THAT THE PRODUCTS ARE FIT FOR‘ANV‘PARTICULAR PURPOSE
OR USE, AND SPECIFICALLY IN LIEU OF ALL SPECIAL, INDIRECT,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
REPAIR OR REPLACEMENT SHALLBE THE SOLE REMEDY OF THE
CUSTOMER AND THERE'SHALL BE’NO LlABiLiTY ON THE PART OF
DESA FOR ANY SPECIAL. thDIRECT, INCIDENTAL. OR CONSE-
QUENTIAL DAMAGES, iNG-LUDING BUT NOT LIMITED TO ANY LOSS
OF BUSINESS OR PROFITS, WHETHER OR NOT FORESEEABLE.
Some states or provinces do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion
may not apply to you. Retain receipt for warranty claims.
DESA International, Inc. resewes the right to discontinue and to change
specifications at any time without notice without incurring any obligation to
incorporate new features in previously sold products.
598- 1 126-00 5.
Remark:
Modifications not authorized by the manufacturer may void users authority to
operate this device.
NOTE:
This equipment has been tested and found to comply wlth limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instruction may cause harmful interference to radio communications.
However, these is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
598- 1 126-00

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 6
Creator                         : May 9, 2002 (60)
Create Date                     : 2002:05:09 16:49:49
Title                           : (60)
Author                          : cee3
Producer                        : Acrobat PDFWriter 4.0 for Windows

EXIF Metadata provided by EXIF.tools