HeathCo 62WDB93TX Wireless Remote Doorbell Transmitter User Manual Users Guide

HeathCo LLC Wireless Remote Doorbell Transmitter Users Guide

Users Guide

Brass TransmitterWireless Push ButtonAccessoryThe Heath®/Zenith Wireless Push Button Acces-sory works with existing Heath®/Zenith jumper ordip switch systems.• Battery powered push button - No wires to run.• 128 selectable codes allow more than onechime system in the same house.© 2001 DESA International 598-1105-00SL-6293/94/95 Brass Transmitter Series(Style may vary from illustration)
-2-598-1105-002. Set the push button dip switches to match the chimereceiver code. See "Code and Tune Setting" section.1. Install two lithium type CR1220 3 voltpush button batteries (included). Re-move back of case by pushing in tabon bottom with a small screwdriver.Make sure batteries are oriented prop-erly (see page 6).4. Mount push button.Remove back of case by pushing in tabon bottom with a small screwdriver.Attach back of case to door jamb or wallwith screws provided. Snap front of pushbutton on.3. Test range. Temporarily position push button where you wantit mounted. Press push button to verify chime and push buttonwork properly. If chime does not sound, see Troubleshooting.
-3-598-1105-00Code and Tune SettingsCode SettingsNote: Most installations will not require you to change any jump-ers or dip switch settings on your chime and push button.WARNING: Disconnect chime unit from power source be-fore opening code access door. Close door and replacescrew before reconnecting to power.The push button and chime communicate by using a code thatcan be changed by switching dip switch positions (or removingand/or adding jumpers) on both the push button and chime. Thecode is factory set; however, there are 128 selectable codesthat allow you to expand your system and prevent outside inter-ference. Other wireless products may cause interference andthe system may not function properly. Follow the instructionsbelow for setting a new code.1.Unplug wireless chime (if applicable).2.Open the cases and locate the jumpers or dip switches onboth the push button and chime (See illustration on page 6).3.The push button and chime both have eight different jumper/dip switch locations. Positions 1 through 7 are used for set-ting the code.4.To change the code, add and/or remove jumpers or changedip switch setting as needed. It is recommended to onlychange one setting at a time and then check to see if system
-4-598-1105-00is functioning properly. Note: Positions 1 through 7 must beexactly the same for both the push button and chime for thissystem to function.Tune SettingsYour Heath®/Zenith wireless chime has different selectable tunes:Ding (one note), Ding-Dong (two note), or Westminster (eightnote) (Available on selected Heath®/Zenith chimes). The fac-tory setting is for the Ding-Dong tune (or Westminster, whenavailable). This tune can be changed by following the instruc-tions below.•Ding (one note tune)Push button: Location 8, Add jumper or set dip switch high (1or ON).•Ding-Dong (two note tune)Push button: Location 8, Remove jumper or set dip switchlow (0 or OFF).Chime: Remove jumper from location 8.•Westminster (Eight note tune) (Available on selected Heath®/Zenith chimes)Push button: Location 8, Remove jumper or set dip switchlow (0 or OFF).Chime: Add a jumper to location 8.
-5-598-1105-00Note: All models have both front and back door tune capabili-ties. You may purchase any Heath®/Zenith wireless push buttonfor a second entrance. We recommend the back door use theDing tune and the front door use the Ding-Dong tune (orWestminster tune, available on selected Heath®/Zenith chimes).Models that include two push buttons will come factory set forfront and back doors. Decals on the rear of the push button willindicate its setting.
-6-598-1105-001 2 3 4 5 6 7 8ON12345678Inside PushButtonReplacing Push Button BatteriesInstall two lithium type CR1220 3 voltbatteries. See diagram inside push but-ton for correct orientation of batteries.* Code Settings1-7 Must MatchBoth PushButton andChimeRemovescrew to openaccess doorTune Setting (Notused on all models)Back ofChimeTuneSettingNote: Some models might require the use oftweezers to remove and replace the jumpersor a small screw driver to set dip switches.Heath®/Zenith reserves the right to discontinue and to changespecifications at any time without notice without incurring anyobligation to incorporate new features in previously sold products.(+) Positive BatteryTerminal
-7-598-1105-00TroubleshootingChime doesn't sound:•Make sure push button and chime codes are the same (See pages 3through 6).•Check orientation of push button batteries (See page 6).•Check charge of push button and chime batteries (if applicable), re-place if necessary.Batteries seem OK, but the chime doesn't work when installed:•Don't mount chime or push button on metal or near metal studs. Thisreduces the transmitter range. Use 1/4" to 1/2" (6 to 13 mm) woodshims to move chime or push button off metal surface.•Concrete floors may reduce range. Move chime away from floor.•Try locating chime closer to push button.The range of the wireless chime can vary with location, temperatureand battery condition.Regulatory InformationThis device (WB-SAW-TX) complies with Part 15 of the FCC Rules andRSS-210 of Industry Canada. Operation is subject to the following twoconditions: (1) this device may not cause harmful interference, and (2)this device must accept any interference received, including interfer-ence that may cause undesired operation.The user is cautioned that changes or modifications not expressly ap-proved by the party responsible for regulatory compliance could voidthe user’s authority to operate the equipment.Do not send products, please call the number listed below:Technical Service: 1-800-858-8501, Ext. 7660, or visit our website:www.desatech.com.DESA International, Inc.P.O. Box 90004, Bowling Green, KY 42102-9004
-8-598-1105-00YOUR HEATH®/ZENITH FIVE YEAR LIMITED WARRANTYThis is a "Limited Warranty" which gives you specific legal rights. You may alsohave other rights which vary from state to state or province to province.For a period of five year from the date of purchase, any malfunction caused byfactory defective parts or workmanship will be corrected at no charge to you.Batteries are not covered. To obtain a refund or a replacement, return theproduct to the place of purchase.Not Covered - Repair service, adjustment and calibration due to misuse, abuseor negligence, light bulbs and other expendable items are not covered by thiswarranty. Unauthorized service or modification of the product or of any furnishedcomponent will void this warranty in its entirety. This warranty does not includereimbursement for inconvenience, installation, setup time, loss of use, or unautho-rized service.This warranty covers only Heath®/Zenith assembled products and is not extendedto other equipment and components that a customer uses in conjunction with ourproducts.THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES,EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY, REPRESENTATIONOR CONDITION OF MERCHANT ABILITY OR THAT THE PRODUCTS ARE FITFOR ANY PARTICULAR PURPOSE OR USE, AND SPECIFICALLY IN LIEU OFALL SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE CUS-TOMER AND THERE SHALL BE NO LIABILITY ON THE PART OF DESA FORANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,INCLUDING BUT NOT LIMITED TO ANY LOSS OF BUSINESS OR PROFITS,WHETHER OR NOT FORESEEABLE. Some states or provinces do not allow theexclusion or limitation of incidental or consequential damages, so the abovelimitation or exclusion may not apply to you. Retain receipt for warranty claims.

Navigation menu