HeathCo WLTX208 Wireless Door Chime Transmitter User Manual

HeathCo LLC Wireless Door Chime Transmitter

User Manual

THANK YOUWe appreciate the trust and condence you have placed in Hampton Bay through the purchase of this wireless motion alert doorbell kit. We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs. Thank you for choosing Hampton Bay!DRAFT COPYUSE AND CARE GUIDEWIRELESS MOTION ALERT DOORBELL KITQuestions, problems, missing parts? Before returning to the store, call Hampton Bay Customer Service 8 a.m. - 5 p.m., CST, Monday - Friday1-844-760-3644HAMPTONBAY.COMIllustrations may vary from actual unit.Item #0000000000Model #HB-7903-02
2Table of ContentsTable of Contents .......................................2Safety Information .....................................2Warranty ....................................................23-Year Limited Warranty ........................2Pre-Installation ..........................................3Planning Installation ..............................3Specications ........................................3Tools Required .......................................3Hardware Included .................................3Package Contents ..................................4Installation .................................................4Operation ...................................................6Care and Cleaning .....................................8Troubleshooting .........................................8Safety InformationPRECAUTIONS □Please read and understand this entire manual before attempting to assemble, install, or operate this doorbell. □All electrical work must be in accordance with national and local electrical codes. If in doubt, consult a qualied electrician.WARNING: To prevent possible SERIOUS INJURY or DEATH never allow small children near batteries. If a battery is swallowed, immediately notify doctor.WARNING: Risk of re. Do not plug the doorbell into a power inverter.NOTE: The motion sensor, push button, and doorbell come synced from the factory. The range of the wireless doorbell can vary with location, temperature, and battery condition.This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.The user is cautioned that changes or modications not expressly approved by the party responsible for regulatory compliance could void the user’s authority to operate the equipment.Warranty3-YEAR LIMITED WARRANTYWHAT IS COVEREDThis product is guaranteed to be free of factory defective parts and workmanship for a period of 3 years from date of purchase. Purchase receipt is required for all warranty claims.WHAT IS NOT COVEREDThis warranty does not include expendable items (such as light bulbs, batteries, etc.), repair service, adjustment and calibration due to misuse, abuse or negligence. Unauthorized service or modication of the product or of any furnished component will void this warranty in its entirety. This warranty does not include reimbursement for inconvenience, installation, setup time, loss of use, unauthorized service, or return shipping charges. This warranty is not extended to other equipment and components that a customer uses in conjunction with this product.Contact the Customer Service Team at 1-844-760-3644 or visit www.hamptonbay.com.
3 HAMPTONBAY.com Please contact 1-844-760-3644 for further assistance.Pre-InstallationPLANNING INSTALLATIONBefore installing the wireless motion alert doorbell kit, ensure that all parts are present. Compare the parts with the Hardware Included and Package Contents sections. If any part is missing or damaged, do not attempt to assemble, install, or operate this wireless motion alert doorbell kit.Estimated installation time: 30 minutesSPECIFICATIONSDoorbell Push button Motion sensorPower requirements 120V, 60 Hz Type A23 12V battery (included)2x - Type “AAA” 1.5V battery (not included)TOOLS REQUIREDPhillips screwdriverSmall athead screwdriver Drill1/16 in. (1.5 mm) Drill bitSafety gogglesHARDWARE INCLUDEDNOTE: Hardware shown to actual size. AA BB CCPart Description QuantityAA Jumper 1BB Screw 4CC Double-sided tape 1
4Pre-Installation (continued)PACKAGE CONTENTS Part Description QuantityADoorbell 1BMotion sensor 1CPush button 1Installation1 Installing the doorbell □Plug in the doorbell (A) at the desired location.2 Installing the batteries into the motion sensor □Remove the screw and cover on the back of the motion sensor (B) using a small Phillips screwdriver (not included). □Install two “AAA” batteries. Ensure the batteries are oriented correctly. □Replace the cover on the back of the motion sensor (B) and tighten the screw.ABCBA
5 HAMPTONBAY.com Please contact 1-844-760-3644 for further assistance.Installation (continued)3 Removing the battery tab □Remove the backs of the push button (C) by pushing in the tab on the bottom with a small athead screwdriver (not included). □Remove the orange battery tab from the push button (C).4 Testing the push button and doorbell □Temporarily position the push button (C) where it will be mounted. □Press the push button (C) to verify the doorbell(A) and push button (C) work properly. □If the doorbell (A) does not sound, move the doorbell (A) closer to the push button (C) and test again.NOTE: Do not permanently mount the sensor or push button until the sensor, push button, and doorbell are all working properly.5 Testing the sensor and doorbellIn most cases, testing of the motion sensor requires two people; one person to activate the sensor (B) and the other to listen for the doorbell (A) to sound. □On the bottom of the motion sensor (B), slide the ON-TIME switch to the “TEST” position. □Temporarily position the sensor (B) near the desired mounting location. □While someone is listening for the doorbell (A) to sound, walk in front of the sensor (B). The red LED on the sensor (B) should ash and the doorbell (A) will sound “Beep-Beep”. In the “TEST” position, all motion must stop for 10 seconds before the sensor (B) will activate the doorbell (A) again. □If the doorbell (A) does not sound, move the doorbell (A) closer to the sensor (B) and test again.NOTE: Do not permanently mount the sensor or push button until the sensor, push button, and doorbell are all working properly.RANGEON-TIMEMAXTEST 1 5 (MINS)MINSYNCRANGEON-TIMEMAXTEST 1 5 (MINS)MINSYNCCABACB
6Installation (continued)6 Mounting the push buttonUse either screws (BB) or double-sided tape (CC) to mount the push button (C). □To mount with screws (BB), remove the back of the push button (C) by pushing in the tab on the bottom with a small athead screwdriver. Place the back of the push button (C) on the door jamb and mark the two screw holes. Attach with screws (BB) and snap on the front of the push button (C). □When attaching the push button (C) with double-sided tape (CC), remove the paper from both sides of the double-sided tape (CC) and apply to a clean surface.7 Mounting the sensorAttach the sensor (B) mounting bracket to a sturdy surface using the screws (BB). Make sure the sensor (B) has an unobstructed view. □Place the sensor (B) mounting bracket in the desired location and mark the two screw holes. Attach the sensor (B) with the screws(BB). □If the sensor (B) was removed from the mounting bracket, use a Phillips screwdriver (not included) to loosen the clamp screw on the mounting bracket. Insert the swivel ball on the sensor (B) into the mounting bracket until it snaps into place. Aim the sensor (B) toward the area to be monitored and tighten clamp screw.NOTE: Attach mounting bracket vertically when attaching to a curved surface.IMPORTANT: The sensor must be rotated so the controls are facing down.Operation1 Adjusting the doorbell volumeThe doorbell (A) has an adjustable volume control located on the side. Rotate the thumbwheel up or down to adjust the volume. ABBBBB
7 HAMPTONBAY.com Please contact 1-844-760-3644 for further assistance.Operation (continued)2 Setting the sensor’s day detectThe sensor (B) can be programmed to operate during the daytime only (DAY ONLY) or both day and night (DAY/NIGHT). □Remove the batteries from the sensor (B). □Slide the “DAY DETECT” switch to the desired mode. Replace the batteries and cover.DAY DETECTDAYDAY/ONLY NIGHT3 Setting the sensor’s rangeThe “RANGE” control increases and decreases the sensitivity of the sensor (B). It also increases and decreases the distance the sensor (B) will detect movement.NOTE: False triggering may happen if the RANGE is set too high. □Adjust the “RANGE” control to increase (MAX) or decrease (MIN) the sensitivity.RANGEON-TIMEMAXTEST 1 5 (MINS)MINSYNC4 Setting the sensor’s on-timeThe “ON-TIME” control determines the amount of time that all motion must be stopped before the sensor (B) will activate the doorbell (A) again. □Select the “ON-TIME” setting desired: □“TEST” - Motion must be stopped for 10 seconds before reactivation. □“1 MIN” - Motion must be stopped for 1 minute before reactivation. □“5 MIN” - Motion must be stopped for 5 minutes before reactivation.RANGEON-TIMEMAXTEST 1 5 (MINS)MINSYNC5 Setting the wireless push buttonThe wireless push button (C) has two options for tune selection: Play the selected “FRONT” door musical tune or play the “REAR” door designated tune (Ding). □Remove the single jumper (AA) inside the push button (C) to play the selected musical tune. □Add the single jumper (AA) inside the push button(C) to play only the Ding tune. Remove jumper to Add jumper to set set as the “FRONT” door as the “REAR” doorBBBAAC
8Operation (continued)6 Selecting a push button tuneThe doorbell (A) has different selectable tunes for different push buttons (sold separately). The push button (C) set as the “REAR” push button will only play “Ding” (one note tune). The push button set as the “FRONT” push button will play either “Ding-Dong” (two note tune) or Westminster (eight note tune). □Press and release the “TUNE” button on the doorbell (A) until the desired tune is heard.NOTE: All doorbell models are designed to work with up to 10 wireless push buttons (sold separately).NOTE: All doorbells are designed to play only two different tunes no matter how many push buttons are used.Motion sensor alertFront door push button(sold separately)Rear door push button(sold separately)Doorbell tune Beep-Beep Ding-Dong or Westminster Ding Care and Cleaning □Use a dry cloth to clean the doorbell, sensor, and push button. □Do not use cleaners or polishes. □Do not use any uids on the doorbell, sensor, and push button.TroubleshootingProblem Possible Cause SolutionThe doorbell does not sound. □The batteries are not installed correctly. □Make sure the batteries are installed according to the diagram inside the sensor and push button. □The batteries are dead. □Check the charge of the sensor and push button batter-ies and replace them if necessary. □The doorbell is not receiving power. □Make sure the plug-in doorbell has power. □The doorbell and the sensor or push button are not synced. □Sync the doorbell to the sensor or push button. Only one sensor or push button may be synced at a time. Repeat these steps for each sensor or push button. □Press and hold the button on the doorbell until the doorbell sounds a “Beep-Beep”. □Press the button on the bottom of the sensor or the push button within 30 seconds. The doorbell will sound a “Beep-Beep” tone to indicate the sensor or the push button is synced. □Test the sensor as shown in step 5 under Installa-tion or press the push button to ensure operation.A
9 HAMPTONBAY.com Please contact 1-844-760-3644 for further assistance.Troubleshooting (continued)Problem Possible Cause SolutionThe doorbell sounds at night. □The day detect switch is in the “DAY/NIGHT” position. □The sensor is functioning correctly. If a doorbell alert is not desired at night, slide the day detect switch to the “DAY ONLY” position.The doorbell does not sound during the day. □The day detect switch is in the “DAY ONLY” posi-tion and the sensor is located in a dark area. □Slide the day detect switch to the “DAY/NIGHT” position or move the sensor to an area that receives more light.The batteries seem okay, but the doorbell does not work after installation. □The doorbell, sensor, or push button is mounted on metal or near metal studs. □Metal reduces transmission range. Use 1/4 in. to 1/2 in. (6 to 13 mm) wood shims to move the doorbell, sensor, or push button away from the metal surface. □The doorbell is mounted near concrete oor or wall. □Concrete may reduce range. Move the doorbell away from the concrete surface. □The doorbell and sensor or push button are installed too far apart. □Locate the doorbell closer to the sensor or push button.The doorbell sounds when not intended (false triggers). □The doorbell is receiv-ing interference from another wireless device. □Reset the doorbell, sensor, and push button. □Remove the sensor and push button batteries. Wait 30 seconds. □Press and hold the button on the bottom of the sen-sor and the push button for 10 to 15 seconds within 60 seconds after installing batteries into the sensor and push button. □Press and hold the button on the doorbell until the doorbell sounds a “Beep-Beep-Beep-Beep”. □Re-sync the doorbell to the sensor and push button. Only one sensor or push button may be synced at a time. Repeat these steps for each sensor or push button. □Press and hold the button on the doorbell until the doorbell sounds a “Beep-Beep”. □Press the button on the bottom of the sensor or the push button within 30 seconds. The doorbell will sound a “Beep-Beep” tone to indicate the sensor or the push button is synced. □Test the sensor as shown in step 5 under Installa-tion or press the push button to ensure operation.
Questions, problems, missing parts? Before returning to the store, call Hampton Bay Customer Service 8 a.m. - 5 p.m., CST, Monday - Friday1-844-760-3644HAMPTONBAY.COMRetain this manual for future use.208191-01A

Navigation menu