HeathCo WLTX209 Wireless Door Chime Transmitter User Manual 208190 01A

HeathCo LLC Wireless Door Chime Transmitter 208190 01A

User Manual

THANK YOUWe appreciate the trust and condence you have placed in Hampton Bay through the purchase of this wireless doorbell and mail reminder kit. We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs. Thank you for choosing Hampton Bay!DRAFT COPYUSE AND CARE GUIDEWIRELESS DOORBELL AND MAIL REMINDER KITQuestions, problems, missing parts? Before returning to the store, call Hampton Bay Customer Service 8 a.m. - 5 p.m., CST, Monday - Friday1-844-760-3644HAMPTONBAY.COMIllustrations may vary from actual unit.Item #0000000000Model #HB-7901-02
2Table of ContentsTable of Contents ......................................2Safety Information ....................................2Warranty ...................................................23-Year Limited Warranty ........................2Pre-Installation .........................................3Planning Installation ..............................3Specications ........................................3Tools Required .......................................3Hardware Included .................................3Package Contents ..................................4Installation ................................................4Operation...................................................6Care and Cleaning ....................................7Troubleshooting ........................................7Safety InformationPRECAUTIONS ƑPlease read and understand this entire manual before attempting to assemble, install, or operate this doorbell. ƑAll electrical work must be in accordance with national and local electrical codes. If in doubt, consult a qualied electrician.WARNING: To prevent possible SERIOUS INJURY or DEATH never allow small children near batteries. If battery is swallowed, immediately notify a doctor.WARNING: Risk of re. Do not plug the doorbell into a power inverter.NOTE: The mailbox sensor, push buttons, and doorbell come synced from the factory. The range of the wireless doorbell can vary with location, temperature, and battery condition.This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.The user is cautioned that changes or modications not expressly approved by the party responsible for regulatory compliance could void the user’s authority to operate the equipment.Warranty3-YEAR LIMITED WARRANTYWHAT IS COVEREDThis product is guaranteed to be free of factory defective parts and workmanship for a period of 3 years from date of purchase. Purchase receipt is required for all warranty claims.WHAT IS NOT COVEREDThis warranty does not include expendable items (such as light bulbs, batteries, etc.), repair service, adjustment and calibration due to misuse, abuse or negligence. Unauthorized service or modication of the product or of any furnished component will void this warranty in its entirety. This warranty does not include reimbursement for inconvenience, installation, setup time, loss of use, unauthorized service, or return shipping charges. This warranty is not extended to other equipment and components that a customer uses in conjunction with this product.Contact the Customer Service Team at 1-844-760-3644 or visit www.hamptonbay.com.
3 HAMPTONBAY.com Please contact 1-844-760-3644 for further assistance.Pre-InstallationPLANNING INSTALLATIONBefore installing the wireless doorbell and mail reminder kit, ensure that all parts are present. Compare parts with the Hardware Included and Package Contents sections. If any part is missing or damaged, do not attempt to assemble, install, or operate this wireless doorbell and mail reminder kit.Estimated installation time: 30 minutesThe mailbox sensor will only work on mailboxes that have a vertical, tilt-style door. Mailboxes with doors that open horizontally (side-to-side) will not work with this sensor.SPECIFICATIONSDoorbell Push buttons Mailbox sensorPower requirements 120 V, 60 Hz Type A23 12V battery (included)Type 2032 3V battery (included)TOOLS REQUIREDPhillips screwdriverSmall athead screwdriver Drill1/16" (1.5 mm) Drill bitSafety gogglesHARDWARE INCLUDEDNOTE: Hardware shown to actual size. AA BB CCPart Description QuantityAA Jumper 1BB Screw 4CC Double-sided tape 3
4Pre-Installation (continued)PACKAGE CONTENTS Part Description QuantityA Doorbell 1B Mailbox sensor 1C Push button 2Installation1 Installing the doorbell ƑPlug in the doorbell (A) at the desired location.2 Removing the battery tab ƑRemove the backs of the sensor (B) and push buttons (C) by pushing in the tab on the bottom with a small screwdriver (not included). ƑRemove the orange battery tab from the sensor (B) and push buttons (C).ABCBCA
5 HAMPTONBAY.com Please contact 1-844-760-3644 for further assistance.Installation (continued)3 Testing the push button and doorbell ƑTemporarily position the push button (C) where it will be mounted. ƑPress the push button (C) to verify the doorbell(A) and push button (C) work properly. ƑIf the doorbell (A) does not sound, move the doorbell (A) closer to the push button (C) and test again.NOTE: Do not permanently mount the sensor or push buttons until the sensor, push buttons, and doorbell are all working properly.4 Testing the sensor and doorbellIn most cases, testing of the mailbox sensor requires two people; one person to take the sensor (B) to the mailbox for testing and the other to listen for the doorbell and watch for the “envelope” icon on the doorbell to light up. ƑTemporarily position the sensor (B) next to the mailbox. ƑWhile someone is watching and listening for the doorbell (A), hold the sensor (B) as shown and rotate to the horizontal position. The red LED on the sensor (B) should ash, the doorbell (A) will sound “Beep-Beep”, and the “envelope” icon will turn ON. ƑTo reset the “envelope” icon to the OFF position, either press and release the button on the side of the sensor (B) or quickly press and release the button on the side of the doorbell (A) twice. ƑIf the doorbell does not sound, move the doorbell closer to the sensor and test again.NOTE: If the button on the side of the sensor is pressed to reset the “envelope” icon, there is a 10 second delay before the sensor will be able to re-activate the chime.NOTE: Do not permanently mount the sensor or push buttons until the sensor, push buttons, and doorbell are all working properly.5 Mounting the push buttonUse either screws (BB) or double-sided tape (CC) to mount the push button (C). ƑTo mount with screws (BB), remove the back of the push button (C) by pushing in the tab on the bottom with a small screwdriver. Place the push button back on the door jamb and mark the two screw holes. Attach with screws (BB) and snap on the front of the push button (C). ƑWhen attaching the push button (C) with double-sided tape (CC), remove paper from both sides of the double-sided tape (CC) and apply to a clean surface.AACBBB
6Installation (continued)6 Mounting the sensor in a wall mounted mailboxUse double-sided tape (CC) to mount the sensor (B). Remove paper from both sides of the double-sided tape (CC) and apply to a clean surface. ƑOpen the lid of the mailbox. ƑHold the sensor (B) with the screwdriver slot pointing upward and the side button on the right side of the sensor (B). ƑApply the double-sided tape (CC) to the back of the sensor (B) and mount on the inside of the mailbox lid.NOTE: When installed correctly, the red LED on the sensor will ash when the mailbox lid is opened.7 Mounting the sensor in a post mounted mailboxUse double-sided tape (CC) to mount the sensor (B). Remove paper from both sides of the double-sided tape (CC) and apply to a clean surface. ƑOpen the door of the mailbox. ƑHold the sensor (B) with the screwdriver slot pointing upward and the side button on the right side of the sensor (B). ƑApply the double-sided tape (CC) to the back of the sensor (B) and mount on the inside of the mailbox lid.NOTE: When installed correctly, the red LED on the sensor will ash when the mailbox door is opened.Operation1 Adjusting the doorbell volumeThe doorbell (A) has an adjustable volume control located on the side. Rotate the thumbwheel up or down to adjust the volume. ABBBBBB
7 HAMPTONBAY.com Please contact 1-844-760-3644 for further assistance.Operation (continued)2 Setting the wireless push buttonNOTE: The two push buttons included in this kit will come factory set for front and back doors. A decal on the rear of the push button will indicate its setting.The wireless push button (C) has two options for tune selection: Play the selected “FRONT” door musical tune or play the “REAR” door designated tune (Ding). ƑRemove the single jumper inside the push button (C) to play the selected musical tune. ƑAdd the single jumper inside the push button(C) to play only the Ding tune. Remove jumper to Add jumper to set set as the “FRONT” door as the “REAR” door3 Selecting a push button tuneThe doorbell (A) has different selectable tunes for push buttons (C). The push button (C) set as the “REAR” push button (C) will only play Ding (one note tune). The push button (C) set as the “FRONT” push button (C) will either Ding-Dong (two note tune) or Westminster (eight note tune). ƑPress and release the “TUNE” button on the doorbell (A) until desired tune is heard.NOTE: All doorbell models are designed to work with up to 10 wireless push buttons (sold separately).NOTE: All doorbells are designed to play only two different tunes no matter how many push buttons are used.Mailbox alertFront door push button(sold separately)Rear door push button(sold separately)Doorbell tune Beep-Beep Ding-Dong or Westminster Ding4 Using the sensorThe sensor (B) will activate the doorbell (A) each time the mailbox is opened. The doorbell (A) will sound a “Beep-Beep” tone and the “envelope” icon will glow. The “envelope” icon will continue to glow until one of the following steps is done: ƑPress and release the button on the side of the sensor (B) or... ƑQuickly press and release the button on the side of the doorbell (A) twice.NOTE: If the button on the side of the sensor is pressed to reset the “envelope” icon, there is a 10 second delay before the sensor will be able to re-activate the chime. This delay will ensure that the mailbox is closed before the sensor will be able to acitvate the doorbell again. AABC
8Care and Cleaning ƑUse a dry cloth to clean the doorbell, sensor, and push buttons. ƑDo not use cleaners or polishes. ƑDo not use any uids on the doorbell, sensor, and push buttons.TroubleshootingProblem Possible Cause SolutionDoorbell does not sound. ƑBatteries not installed correctly. ƑMake sure batteries are installed according to the diagram inside the sensor and push buttons. ƑBatteries are dead. ƑCheck the charge of the sensor and push button batter-ies and replace if necessary. ƑDoorbell is not receiving power. ƑMake sure the plug-in doorbell has power. ƑThe doorbell and the sensor or push buttons are not synced. ƑSync the doorbell to the sensor or push button(s). Only one sensor or push button may be synced at a time. Repeat these steps for each sensor or push button. ƑPress and hold the button on the doorbell until the doorbell sounds a “Beep-Beep”. ƑPress the button on the side of the sensor or the push button(s) within 30 seconds. The doorbell will sound a “Beep-Beep” tone to indicate the sensor or the push button(s) is synced. ƑRotate the sensor as shown in step 4 under Installa-tion or press the push button(s) to ensure operation.
9 HAMPTONBAY.com Please contact 1-844-760-3644 for further assistance.Troubleshooting (continued)Problem Possible Cause SolutionBatteries seem okay, but the doorbell does not work after installation. ƑDoorbell or push button(s) is mounted on metal or near metal studs. ƑMetal reduces transmission range. Use 1/4 in. to 1/2 in. (6 to 13 mm) wood shims to move the doorbell or push button(s) away from the metal surface. ƑDoorbell is mounted near concrete oor or wall. ƑConcrete may reduce range. Move the doorbell away from the concrete surface. ƑDoorbell and sensor or push button(s) are installed too far apart. ƑLocate the doorbell closer to the sensor or push button(s).The “envelope” icon glows continually. ƑReset the “envelope” icon. ƑTo reset the icon, press and release the button on the side of the sensor or quickly press and release the but-ton on the side of the doorbell twice.Doorbell sounds when not intended (false triggers). ƑDoorbell is receiving in-terference from another wireless device. ƑReset the doorbell, sensor, and push buttons. ƑRemove the sensor and push button batteries. Wait 30 seconds. ƑPress and hold the push buttons and the button on the side of the sensor for 10 to 15 seconds within 60 seconds after installing batteries into the push buttons and sensor. ƑPress and hold the button on the doorbell until the doorbell sounds a “Beep-Beep-Beep-Beep”. ƑRe-sync the doorbell to the sensor and push buttons. Only one sensor or push button may be synced at a time. Repeat these steps for each sensor or push button. ƑPress and hold the button on the doorbell until the doorbell sounds a “Beep-Beep”. ƑPress the button on the side of the sensor or the push button within 30 seconds. The doorbell will sound a “Beep-Beep” tone to indicate the sensor or the push button is synced. ƑRotate the sensor as shown in step 4 under Installa-tion or press the push button(s) to ensure operation.
Questions, problems, missing parts? Before returning to the store, call Hampton Bay Customer Service 8 a.m. - 5 p.m., CST, Monday - Friday1-844-760-3644HAMPTONBAY.COMRetain this manual for future use.208190-01A

Navigation menu