HeathCo WRC6033TX Wireless PIR Motion Sensor User Manual 598 1271 00 indd

HeathCo LLC Wireless PIR Motion Sensor 598 1271 00 indd

User manual

DRAFT COPYON1 2 3 4ON1 2 3 4ON1 2 3 4ENGLISHRemote Controlled ProductsThis manual includes operating instructions for a variety of remote controlled products. All products work on the same principle and use the same code setting information. Please read all instructional information and note any specific information pertaining to your particular product.FEATURES• Products are UL/cUL and/or FCC/IC tested and approved.• Operational range of up to 100 feet.Heath®/Zenith wireless lighting controls are designed to work together. Simply determine which transmitter(s) you would like to have control which receiver(s) and set the code setting to match.CODE SETTINGSNote: Most single system installations will not require any change to the code setting. Transmitter(s) and receiver(s) must have the same code and group setting to work together. Switches 1 through 3 set the code. Switch 4 sets the Group (A or B). See page 2 for switch locations.Transmitter(s)/ Receiver(s) CodeGroup “B”Example 1 - Code Settings, System 1(Factory Setting)Transmitter(s)/ Receiver(s) CodeGroup “A”( – Indicates Position of Switch)Example 2 - Code Settings, System 2Note: When operating more than one system independently of each other, set each system to a different code. There are 8 codes avail-able by changing the settings of switches 1 through 3.Transmitter(s)/Receiver(s) CodeGroup “A”© 2006 DESA Specialty Products™ 598-11271-00CODE SWITCH LOCATIONSSolar Powered Motion SensorCode SwitchesON DUALBRITE® ON-TIMEOff 3Hr Dusk to TEST 1 5 Dawn (Mins)CODE RANGE DETECT1 2 3 4 MIN MAX NIGHT DAY ONLY NIGHTON1 2 3 4Close-Up of Typical Code Switch(Factory Default Setting is Off)Note: The “X” has been placed on the switches to help clarify the code settings on the previous page.
2598-1271-00DRAFT COPYSOLAR POWERED MOTION SENSORFeatures:• No wiring required.• Up to 80 feet sensing range, 360° Cover-age.• Adjustable sensitivity.• Day/Night or Night only operation.• Optional half power accent lighting• Test mode.• Uses 2 AAA NiMH rechargeble batteries (included).• Controls receivers up to 100 feet away.Solar Powered Motion SensorLockUnlockInstalling Batteries1. Remove battery compartment cover by rotating clear solar panel cover counterclockwise.2. Install 2 AAA NiMH rechargeble batteries (included) according to polarity markings inside the battery compartment.3. Replace battery compartment cover by reversing the above instructions.Lock UnlockLock UnlockRemoving Solar Panel Cover / Battery Compartment - Top ViewClear Solar Panel CoverRotation IndicatorsSolar Panel Cover / Battery Compartment - Bottom View
3598-1271-00ENGLISHDRAFT COPYContinuedDUALBRITE® Dimmer ControlLight comes on half power for selected time after dusk (Off, 3 hr., until dawn). If motion is sensed, the light turns on full power for the ON-TIME (1 or 5 minutes) then returns to accent mode.1. Select amount of time for accent lighting (DUALBRITE® con-trol).2. Select the amount of time light stays on full bright after motion is detected (On-Time control).Night Only or 24 Hour ModeThis sensor is able to detect motion day and night or night only. Slide the DETECT switch to either the DAY/NIGHT or NIGHT ONLY position.Range ControlAdjust the RANGE to increase or decrease the range as needed. Too much sensitivity may cause false triggering due to heat sources in the coverage area.The sensor on this light fixture detects “motion” by the movement of heat (body heat) across the coverage area. However, following are examples of objects that also produce heat and can cause the sensor to false trigger:• Pools of Water • Air Conditioners• Dryer Vents • Fenced-In Animals• Heating Vents • Automobile TrafficIf you suspect that a heat source of this type is falsely triggering the sensor, adjust the RANGE control as needed to avoid false triggering.LockUnlockSETTING CONTROLSThe controls are located on the bottom of the sensor unit. To remove the base, carefully grasp the sensor unit and the base and pull apart. IMPORTANT: Be careful not to press against the sensor lenses when grasping the sensor unit.ON DUALBRITE® ON-TIMEOff 3Hr Dusk to TEST 1 5 Dawn (Mins)CODE RANGE DETECT1 2 3 4 MIN MAX NIGHT DAY ONLY NIGHTON DUALBRITE® ON-TIMEOff 3Hr Dusk to TEST 1 5 Dawn (Mins)CODE RANGE DETECT1 2 3 4 MIN MAX NIGHT DAY ONLY NIGHTON DUALBRITE® ON-TIMEOff 3Hr Dusk to TEST 1 5 Dawn (Mins)CODE RANGE DETECT1 2 3 4 MIN MAX NIGHT DAY ONLY NIGHTON DUALBRITE® ON-TIMEOff 3Hr Dusk to TEST 1 5 Dawn (Mins)CODE RANGE DETECT1 2 3 4 MIN MAX NIGHT DAY ONLY NIGHTON DUALBRITE® ON-TIMEOff 3Hr Dusk to TEST 1 5 Dawn (Mins)CODE RANGE DETECT1 2 3 4 MIN MAX NIGHT DAY ONLY NIGHTDetect ControlDUALBRITE® Control ON-TIME ControlRange ControlSensor LenseBaseSensor UnitRemoving Base from Sensor UnitSetting Controls - Bottom View of Sensor UnitSolar Panel Cover / Battery CompartmentLED Indicator
4598-1271-00DRAFT COPYInstalling Solar Motion Sensor1. Attach the sensor unit to the ground spike. Note: If you need to raise the sensor unit an additional 6”, use the extension rod.2. Determine where you want to install the motion sensor. IMPORTANT: Place sensor where it will be able to receive 4 to 6 hours of direct sunlight each day.3. Aim the sensors in the direction of desired coverage. Note: The sensors have a greater range directly in front of them than they do to the sides.4. While holding the ground spike in the direction determined, remove the sensor unit (and extension rod if attached).5. Place the ground spike on the ground and press into the soil. If necessary, use a rubber mallet to drive the ground spike into the ground.6. Reattach the sensor unit (and extension rod, if applicable) to the ground spike.Check Operation and AdjustmentNote: When first turned on or when switching modes wait 30 seconds.Note: When using test mode to check operation in the day time, set the DETECT control switch to DAY/NIGHT.1. Check Operation. Set the ON-TIME control to TEST mode. Walk in front of sensor unit. The LED indicator light should flash when motion is detected (see illustration, page 4, for location of LED light).2. Adjust Sensor. Turn the RANGE control to the mid position and ON-TIME control to the TEST position. Walk through coverage area noting where you are when the LED begins to flash.3. Adjust RANGE Control. To increase sensitivity, turn the RANGE control toward MAX. To decrease sensitivity, turn the RANGE control toward MIN. Note: If the RANGE is set too high, false triggering may result in some environments.4. Set ON-TIME Control. Determine the amount of time you want the connected device to stay on after motion is detected (1 or 5 minutes). Slide the ON-TIME control to the corresponding setting.5. Make adjustments and snap sensor unit onto base.IMPORTANT: Avoid Aiming Control At:• Objects that change temperature rapidly, such as heating vents, fans, and air conditioners. These air sources could cause false triggering.• Areas where pets or traffic may trigger the control.• Nearby large, light colored objects reflecting light may trigger the shut-off feature. Do not point other lights at the sensor.Indoor and Outdoor Motion Sensor SensitivityThe detector is most sensitive to motion across its field of view.Most SensitiveLeast SensitiveSensor SensorMaximum Coverage AngleMaximum RangeSolar Motion Sensor Coverage Area80 ft. (24.4 m)360°LockUnlockSensor UnitExtension RodGround SpikeSensorsMotionMotion
5598-1271-00ENGLISHDRAFT COPYTROUBLESHOOTING GUIDEREGULATORY INFORMATIONThis device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.The term “IC:” before the radio certification number only signifies that Industry Canada technical specifications were met.The user is cautioned that changes or modifications not expressly approved by the party responsible for regulatory compliance could void the user’s authority to operate the equipment.TECHNICAL SERVICEPlease call 1-800-858-8501 for assistance before returning product to store.If you experience a problem, follow this guide. You may also want to visit our Web site at: www.desatech.com. If the problem persists, call* for assistance at 1-800-858-8501, 7:30 AM to 4:30 PM CST (M-F). You may also write* to:DESA Specialty Products™ATTN: Technical Service Specialty ProductsP.O. Box 90004Bowling Green, KY 42102-9004* If contacting Technical Service, please have the following information available: Model Number, Date of Purchase, and Place of Purchase.No Service Parts Available for this ProductSYMPTOM POSSIBLE CAUSE SOLUTIONSwitched device does not come on. 1. Circuit breaker or fuse is turned off. 1. Verify circuit breaker or fuse is turned on.2. Switched device is turned off. 2. Verify switched device is turned on.3. Interrupted by another device. 3. Change codes on transmitter and receiver units.4. Does not respond immediately after installation.4. Wait for 45 second initialization period (remote motion sensor).5. Signals from transmitter are being blocked, or transmitter is out of range.5. Check for metal objects that could block the signal, or reposition the transmitter.6. Weak battery in the transmitter. 6. Check battery charge and replace if necessary.7. Dip switches on transmitter and receiver units do not match.7. Verify code settings on transmitter and receiver units are set the same.8. Switched device is defective. 8. Test using different switched device.Switched device does not turn off. 1. Same as 5, 6, and 7 above. 1. Same as 5, 6, and 7 above.Switched device comes on randomly. 1. Short term power line failure. 1. Next transmission from transmitter will reset receiver to correct state.2. Another transmitter on the same frequency.2. Change codes on transmitter and receiver units.
6598-1271-00DRAFT COPYTWO YEAR LIMITED WARRANTYThis is a “Limited Warranty” which gives you specific legal rights. You may also have other rights which vary from state to state or province to province.For a period of two years from the date of purchase, any malfunction caused by factory defective parts or workmanship will be corrected at no charge to you.Not Covered - Repair service, adjustment and calibration due to misuse, abuse or negligence, light bulbs, batteries, and other expendable items are not covered by this warranty. Unauthorized service or modification of the product or of any furnished component will void this warranty in its entirety. This warranty does not include reimbursement for inconvenience, installation, setup time, loss of use, unauthorized service, or return shipping charges.This warranty covers only DESA Specialty Products™ assembled products and is not extended to other equipment and com-ponents that a customer uses in conjunction with our products.THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY, REPRESENTATION OR CONDITION OF MERCHANT ABILITY OR THAT THE PRODUCTS ARE FIT FOR ANY PARTICULAR PURPOSE OR USE, AND SPECIFICALLY IN LIEU OF ALL SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE CUSTOMER AND THERE SHALL BE NO LIABILITY ON THE PART OF DESA SPECIALTY PRODUCTS™ FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO ANY LOSS OF BUSINESS OR PROFITS, WHETHER OR NOT FORESEEABLE. Some states or provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Proof of purchase is required for warranty claims.DESA Specialty Products™ reserves the right to discontinue products and to change specifications at any time without incurring any obligation to incorporate new features in products previously sold.

Navigation menu