Hetronic MFSHL-BMTX Wireless Controller User Manual User s Manual Bomag MFSHL
Hetronic International Inc Wireless Controller User s Manual Bomag MFSHL
Hetronic >
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 662225 |
| Application ID | LVtm/fvrMcQyosZtJKf1ww== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 16.7kB (208704 bits) |
| Date Submitted | 2006-05-26 00:00:00 |
| Date Available | 2006-05-26 00:00:00 |
| Creation Date | 2006-03-27 17:38:25 |
| Producing Software | Acrobat Distiller 5.0.5 (Windows) |
| Document Lastmod | 2006-03-27 17:38:25 |
| Document Title | Microsoft Word - User's Manual-Bomag-MFSHL.doc |
| Document Creator | PScript5.dll Version 5.2.2 |
| Document Author: | rflores |
User’s Manual MFSHL-BMTX Transmitter 1. DESCRIPTION The MFSHL-BMTX is a transmitter/coder with an RF section that uses a Binary FSK Modulation with a frequency of 915MHz, 76800 Baud rate and 3% Duty Cycle. The coder also works in cable control mode. When the coder detects a cable connection, no signal is given to the RF section. Instead, a CAN output is given to the cable. Note: Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference that may cause undesired operation of the device. 2. TECHNICAL SPECIFICATIONS Temperature Range Supply Voltage Range Supply Current Outputs Inputs RF Specifications Frequency Modulation Deviation Output Power -20o to +70o Celsius 2-5 VDC 42mA max 28mA for 5 seconds on startup RF-Data 2 LED 24 digital 915.0 MHz Binary FSK 64KHz 5dBm Note: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 3. FUNCTIONAL DESCRIPTION 3.1. Transmitter Operation • • • The MFSHL-BMTX is capable of transmitting 24 DKs including DK32 and DK31. When E-Stop is activated, all DKs are OFF except for DK31. During Cable mode, when the main contact turns ON, CAN output will be activated. The DK1 can be used to reset the receiver from main contact error. MFSHL-BMTX Connection Description 3.2. LED Description 3.2.1. CAN LEDs Red LED o Flashing –CAN power is on. o Solid – CAN is connected to a CAN bus Green LED o Flashing – Valid telegram transmitted 3.2.2. System LEDs Green LED o Flashing – Transmission of telegram on RF o On – Transmission of telegram in cable mode Red LED o Flashing – Transmission of telegram when battery is low. o Flashing (alternate with Green) – Main contact error Yellow LED o Flashing – System is running (watch dog LED) Green, Red, & Yellow o Flashing at Startup – System is working 3.3. Buzzer Description • 2 short beeps at Startup – System is working. • Short beep every 5 seconds – Low Voltage Warning. • Regular beeping – Battery failure. 3.4. Low Voltage Indicator The Low Voltage Indicator has two levels of detection. The first is a pre warning that triggers when the battery is at 3.5V. At this time, the buzzer will begin to give a short beep every 5 seconds, and the LED will start blinking RED. When the battery voltage reaches 3.4 volts the buzzer will begin beeping regularly. After 30 seconds the transmitter will send two seconds of E-Stop telegrams and then turn off. Power must be cycled to turn on the unit again. 3.5. Test Mode Short Jumper J3 to continuously transmit RF signal for testing. Short J3 for Test mode
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Create Date : 2006:03:27 17:38:25-06:00 Modify Date : 2006:03:27 17:38:25-06:00 Page Count : 4 Creation Date : 2006:03:27 23:38:25Z Mod Date : 2006:03:27 23:38:25Z Producer : Acrobat Distiller 5.0.5 (Windows) Author : rflores Metadata Date : 2006:03:27 23:38:25Z Creator : rflores Title : Microsoft Word - User's Manual-Bomag-MFSHL.docEXIF Metadata provided by EXIF.tools