Hewlett Packard Enterprise APEX0100101 Access Point User Manual Professional installation Guide v2

Download:
Mirror Download [FCC.gov]
Document ID	2227790
Application ID	cSEWT/dhxorawle/tebYOQ==
Document Description	Professional installation Guide v2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	4.12kB (51440 bits)
Date Submitted	2014-03-28 00:00:00
Date Available	2014-03-14 00:00:00
Creation Date	2014-03-28 13:22:39
Producing Software	GPL Ghostscript 9.10
Document Lastmod	2014-03-28 13:22:39
Document Title	Professional installation Guide v2
Document Creator	PDFCreator Version 1.7.2
Document Author:	Wade.Zhang

Professional installation Guide
Product/s covered in this guide: Device: APEX0100 and APEX0101 is part of the
Aruba’s APEX0100 family, implementing dual radio cards each 3x3 MIMO
supporting IEEE 802.11 a/b/g/n/ac operation.
IMPORTANT - Visit Aruba Support web page for the latest information and
documentation related to this product.
IMPORTANT – Please read this document before installing and using your
product. This device must be installed and used in strict accordance with the
manufacturer's instructions. Only approved by the manufacturer power adapters must
be used. For replacement, contact your supplier or distributor.
Installation of this product must comply with local regulations and codes. When this
product is used with external antenna/s, please refer to the installation documentation
provided for the antenna/s. Changes or modifications to the device not approved by the
manufacturer of the product could void the user’s authority to operate the equipment
and will void the warranty of the product. No user serviceable parts; all repairs and
service must be handled by a qualified service center. All products using external
antennas must be professionally installed, and the transmit power of the system must
be adjusted by the professional installer/s to ensure that the system’s EIRP is in
compliance with the limit specified by the regulatory authority of the country of
deployment. During deployment of the system and its initial setup, professional
installer must ensure that the allowed EIRP limit is not exceeded (in the Country of
exploitation of this equipment).
To achieve this professional installer must use approved and recommended by the
Manufacturer antennas,
Model
Type
ANT-3X3-2005
Omni
ANT-3X3-5005
Omni
ANT-2X2-D805
Directional
ANT-3X3-5712
Directional
ANT-2X2-2314
Directional
ANT-2X2-5314
Directional
ANT-2X2-2714
ANT-3X3-5010
Directional
Omni
ANT-2X2-D607
Directional
ANT-3X3-D608
Directional
ANT-3X3-D905
Directional
Gain ( dBi)
NA
NA
NA
11.5
14
NA
NA
14
14
10
Frequency Band ( MHz)
2400-2500
4900-5900
2400-2500
4900-5875
2400-2500
4900-5875
2400-2500
4900-6000
2400-2500
4900-5875
2400-2500
4900-6000
2400-2483
4900-5875
2400-2500
4900-5875
2400-2500
4900-5900
2400-2500
4900-5900
and enter Antenna gain in the software using to setup and manage the product. In
additional attenuation between the device and antenna may have to be measured or
calculated. The following formula can be used to calculate from EIRP limit related
RF power based on selected antennas (antenna gain) and feeder (Coaxial Cable loss):
EIRP = Tx RF Power (dBm) +GA (dB) - FL (dB);
EIRP –> limit specific for each Country of deployment
Tx RF Power –> RF power measured at RF connector of the unit
GA –> Antenna gain
FL -> Feeder loss (including the connectors’ loss)
This device has been designed to operate with antennas listed above and having a
maximum gain listed below. Antennas not included in this list or having gain greater
than specified below are strictly prohibited for use with this device. The require
Antenna Impedance is 50 Ohms.
Attention to user and installation person:
According to §2.1091, §2.1093 and §1.1307(b), systems operating under the
provisions of this section shall be operated in a manner that ensures that the public is
not exposed to radio frequency energy level in excess of the Commission’s guidelines.
The power density(S) must less than 1 mW/cm2,
S = PG / (4πR2)
Where:
S = power density in mW/cm2;
P = transmit power in mW;
G = numeric gain of transmit antenna;
R = distance (cm)
(Which according to user manual for a safety use distance, default 35cm.)
numeric gain=Log-1(dB antenna gain/10)
The user and installation person should calculated the Power density(S) before using
and insure that less than 1 mW/cm2.
For example:
Where Product transmit power from 2.4GHz band：
Port 0=50mW, port 1=50mW, port 2=50mW,
The total transmit power= port 0+ port 1+ port 2 = 50mW+50mW+50 mW = 150mW;
Where Product transmit power from 5GHz band：
Port 0=50mW, port 1=50mW, port 2=50mW,
The total transmit power= port 0+ port 1+ port 2 = 50mW+50mW+50 mW = 150mW;
If User’s antenna with 14dBi gain max(for 2.4GHz band and 5GHz band),
the numeric gain=Log-1(dB antenna gain/10) = Log-1(14/10)=25.12dBi;
R=35(cm)(Satety warning in User Manual),
S limit=1mW/cm2,
According to the formula:
S = PG / (4πR2)
For 2.4GHz band:
S1 =150*25.12/(4*3.14*35*35)= 0.245<1mW/cm2.
For 5GHz band:
S2=150*25.12/(4*3.14*35*35)= 0.245<1mW/cm2.
S(Total)=S1+S2=0.245+0.245=0.490<1mW/cm2.
So,it compliance to FCC rules.
Antenna Types and Maximum Antenna Gains
Frequency Band
Type
Gain(dBi)
Omni
2.4GHz
Directional
14
Omni
10
5GHz
Directional
14
Note: Antenna information provided above reflect approved antennas for initial
release of the device. For full list of antennas approved/recommended by the
Manufacture please visit the Aruba Networks Inc. web site.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 3
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:7e0e9da1-b894-11e3-0000-fb2d955285ba
Producer                        : GPL Ghostscript 9.10
Keywords                        : ()
Modify Date                     : 2014:03:28 13:22:39+08:00
Create Date                     : 2014:03:28 13:22:39+08:00
Creator Tool                    : PDFCreator Version 1.7.2
Document ID                     : uuid:7e0e9da1-b894-11e3-0000-fb2d955285ba
Format                          : application/pdf
Title                           : Professional installation Guide v2
Creator                         : Wade.Zhang
Description                     : ()
Author                          : Wade.Zhang
Subject                         : 

EXIF Metadata provided by EXIF.tools