Hewlett Packard Enterprise APINH203 ACCESS POINT User Manual 203H IG Rev02

Aruba Networks, Inc. ACCESS POINT 203H IG Rev02

TempConfidential_APINH203_User Manual

Aruba 203H Hospitality Access PointsInstallation GuideRev02 | March 2017 1The Aruba 203H access points (APs) are high-performance flex-radio (software configuable as either single radio dual-band or dual radio) wireless devices for hospitality and branch deployments. These access points use Multiple-Input, Multiple-Output (MIMO) technology to provide secure wireless connectivity for both 2.4GHz 802.11 b/g/n and 5GHz 802.11 a/n/ac WiFi.Package Contents203H access pointSingle gang wall-box mounting bracket2x #6-32 machine screwsA security tool203H Hardware OverviewFigure 1 FrontLEDsThe 203H has three LEDs that indicate the system, radio and E1 port status of the device. These LEDs can be configured via software into three separate modes:!CAUTIONThis device must be professionally installed and serviced by a trained ACMP or similar Aruba-certified technician. Aruba access points are classified as radio transmission devices, and are subject to government regulations of the host country. The network administrator(s) is/are responsible for ensuring that configuration and operation of this equipment is in compliance with their country’s regulations. For complete list of approved channels in your country, refer to the Aruba Downloadable Regulatory Table at support.arubanetworks.com.A security tool is provided with every ten access points. Inform your supplier if there are any incorrect, missing, or damaged parts. If possible, retain the carton, including the original packing materials. Use these materials to repack and return the unit to the supplier if needed.
2Aruba 203H Hospitality Access Points | Installation GuideNormal mode (by default): See Table 1Off mode: All LEDs offBlink mode: All LEDs blink green (synchronized)Table 1 203H LEDs Status in Normal ModeLED Color/State MeaningSystem Off Device powered offGreen- Blinking Device booting, not ready for useGreen- Solid Device ready for use, no restrictionsGreen- Flashing Device ready for use, uplink negotiated in sub optimal speed (<1Gbps)Red- Solid System error conditionRadio Off Device powered off, or both radios disabledGreen- Solid Both radios enabled in access modeGreen- Blinking One radio enabled in access modeAmber- Solid Both radios enabled in monitor modeAmber- Blinking One radio enabled in monitor modeAlternating One radio enabled in access mode, other in monitor modeE1 Off Device powered off, port disabled, or no link establishedGreen- Solid Link establishedGreen- Blinking Activity
Aruba 203H Hospitality Access Points | Installation Guide 3Figure 2 BottomFigure 3 BackEthernet PortThe 203H access point is equipped with two Ethernet ports (E0 and E1). The E0 is a 10/100/1000 Base-T auto-sensing MDI/MDX wired-network uplink connectivity port. It supports IEEE 802.3af Powerover Ethernet (PoE), accepting 48V DC as a standard powered device (PD) from power sourcing equipment (PSE), including PoE midspan injector or a PoE-sourcing network infrastructure.The E1 is a 10/100/1000 Base-T auto-sensing MDI/MDX wired-network downlink connectivity port, used to provide secure network connectivity to wired devices.The E0/PT port can serve as an E0 uplink port and accepts 802.3af PoE power when the Pass-Through (PT) and E0 ports are physically bridged by an AP-CBL-Eth10 Ethernet cable (sold separately).BLE Radio PortThe 203H is equipped with a BLE radio port compatible with Bluetooth Low Energy (BLE) dongles. This BLE radio port supports Aruba USB Beacons. Console PortThe serial console port is a 4-pin connector covered by a dust cover. An optional serial adapter cable (AP-CBL-SER) is sold separately to connect the device to a serial terminal or a laptop for direct local management. Reset/LED Control ButtonTo reset the 203H access points to factory default settings, press and hold down the reset button using a small, narrow object such as a paper clip for several seconds while the device is being powered on, or for more than 10 seconds during normal operation. To turn off/on the LED display, press this button using a small, narrow object such as a paper clip for less than 10 seconds during normal operation.E1 PortE0/PT Port BLE RadioPT PortE0 PortConsole Port
4Aruba 203H Hospitality Access Points | Installation GuideBefore You BeginPre-Installation Network RequirementsAfter WLAN planning is complete and the appropriate products and their placement have been determined, the Aruba controller(s) must be installed and initial setup performed before the Aruba access points are deployed.For initial setup of the controller, refer to the Quick Start Guide for the software version installed on your controller.Pre-Installation ChecklistBefore installing your 203H access points, ensure that you have the following:Pre-installed wall boxCat5E or better UTP cable with network access installed in the wall boxOne of the following power sources:IEEE 802.3af-compliant Power over Ethernet (PoE) source. For AP-203H running ArubaOS only:Aruba Controller provisioned on the network:Layer 2/3 network connectivity to your access pointOne of the following network services:Aruba Discovery Protocol (ADP)DNS server with an “A” recordDHCP Server with vendor-specific optionsVerifying Pre-Installation Connectivity!CAUTIONFCC Statement: Improper termination of access points installed in the United States configured to non-US model controllers will be in violation of the FCC grant of equipment authorization. Any such willful or intentional violation may result in a requirement by the FCC for immediate termination of operation and may be subject to forfeiture (47 CFR 1.80).!CAUTIONEU Statement: Lower power radio LAN product operating in 2.4 GHz and 5 GHz bands. Please refer to the ArubaOS User Guide/Aruba Instant User Guide for details on restrictions.Produit réseau local radio basse puissance operant dans la bande fréquence 2.4 GHz et 5 GHz. Merci de vous referrer au ArubaOS User Guide/Aruba Instant User Guide pour les details des restrictions.Low Power FunkLAN Produkt, das im 2.4 GHz und im 5 GHz Band arbeitet. Weitere Informationen bezlüglich Einschränkungen finden Sie im ArubaOS User Guide/Aruba Instant User Guide.Apparati Radio LAN a bassa Potenza, operanti a 2.4 GHz e 5 GHz. Fare riferimento alla ArubaOS User Guide/Aruba Instant User Guide per avere informazioni detagliate sulle restrizioni.The instructions for this section are applicable to the 360 Series access points running ArubaOS only.Aruba Networks, Inc., in compliance with governmental requirements, has designed the 203H access points so that only authorized network administrators can change the settings. For more information about access point configuration, refer to the Quick Start Guide and ArubaOS User Guide/Aruba Instant User Guide.The instructions for this section are applicable to the 360 Series access points running ArubaOS only.
Aruba 203H Hospitality Access Points | Installation Guide 5Before installing access points in a network environment, make sure that they are able to locate and connect to the controller after power on.Specifically, you must verify the following conditions:When connected to the network, each access point is assigned a valid IP addressAccess points are able to locate the controller Refer to the Quick Start Guide for instructions on locating and connecting to the controller.Identifying Specific Installation LocationsUse the access point placement map generated by Aruba’s RF Plan software application to determine the proper installation location(s). Each location should be as close as possible to the center of the intended coverage area and should be free from obstructions or obvious sources of interference. These RF absorbers/reflectors/interference sources will impact RF propagation and should have been accounted for during the planning phase and adjusted for in RF plan.Identifying Known RF Absorbers, Reflectors and Interference SourcesIdentifying known RF absorbers, reflectors, and interference sources while in the field during the installation phase is critical. Make sure that these sources are taken into consideration when you attach an access point to its fixed location. Examples of sources that degrade RF performance include:Cement and brickObjects that contain waterMetalMicrowave ovensWireless phones and headsetsInstalling the Access PointThe 203H access point is designed to mount into a variety of electrical gang boxes.1. Remove the existing data wall plate (if applicable).2. Remove any existing RJ45 connectors (typically snap-in) or cut/remove the UTP cable.3. Use a short Ethernet cable (sold separately) to connect the E0 port to an RJ45 connector, or crimp an RJ45 plug (not supplied) on the cable and insert into the E0 port. 4. Depending on the types of your wall boxes, you can choose different holes from the mounting bracket to attach the bracket onto the wall box (see Figure 4 and Figure 5). The applicable standards for the wall boxes are:IEC 60670-1, GB17466, BS4662 and DIN49073 for WorldwideANSI/NEMA OS 1 and OS 2 for USService to all Aruba Networks products should be performed by an AMCP certified technician or similar.
6Aruba 203H Hospitality Access Points | Installation GuideFigure 4 Securing Bracket to US Single Gang Wall BoxFigure 5 Securing Bracket to Worldwide Single Gang Wall Box 5. Align the mounting holes of the mounting bracket with the mounting holes on the wall box. Insert the two included machine screws and tighten them to secure the mounting bracket.6. Connect any required cables to the back of the 203H access point.7. Align the mounting slots on the back of the access point over the corresponding mounting posts on the bracket and slide the access point into place (see Figure 6).Figure 6 Securing the 203H Access Point to the Bracket
Aruba 203H Hospitality Access Points | Installation Guide 7Removing the Access Point from the BracketInsert the included security tool into the holes at the bottom of the bracket and push the access point up to release it from the bracket (see Figure 7).Figure 7 Removing the 203H Access Point from the BracketConnecting Required CablesInstall cables in accordance with all applicable local and national regulations and practices.Verifying Post-Installation ConnectivityThe integrated LEDs on the access point can be used to verify that the access point is receiving power and initializing successfully (see Table 1). Refer to the Quick Start Guide for further details on verifying post-installation network connectivity.Electrical and Environmental SpecificationsFor additional specifications on this product, please refer to the product data sheet at www.arubanetworks.com/safety_addendum.ElectricalEthernet:E0: Uplink network interface 100/1000 Base-T auto-sensing Ethernet RJ45 port.E1: Downlink network interface 100/1000 Base-T auto-sensing Ethernet RJ45 port.Power over Ethernet IEEE 802.3af 48VDCEnvironmentalOperating:Temperature: 0°C to +40°C (+32°F to +104°F)Humidity: 5% to 93% non-condensingStorage and transport:For instruction on the access point configuration, please refer to the ArubaOS User Guide.!CAUTIONAll Aruba access points should be professionally installed by an Aruba Certified Mobility Professional (ACMP). The installer is responsible for ensuring that grounding is available and meets applicable national and electrical codes.!CAUTIONTous les points d'accès Aruba doivent impérativement être installés par un professionnel agréé. Ce dernier doit s'assurer que l'appareil est mis à la terre et que le circuit de mise à la terre est conforme aux codes électriques nationaux en vigueur.
8Aruba 203H Hospitality Access Points | Installation GuideTemperature: -40°C to +70°C (-40°F to +158°F)Regulatory InformationThe regulatory model name for the 203H access point is APINH203.FCCThis device is electronically labeled.To view the FCC ID for controller-managed access points:1. Log into the controller WebUI2. Navigate to Maintenance > Controller > AboutTo view the FCC ID for Instant access points:1. Log into the virtual controller WebUI2. Navigate to Maintenance > AboutFCC Class B Part 15This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer’s instructions, may cause interference harmful to radio communications.Operation is subject to the following conditions:This device may not cause harmful interference.This device must accept any interference received, including interference that may cause undesired operation.If this equipment does cause interference, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver.Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.Consult the dealer or an experienced radio or TV technician for help.!CAUTIONRF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits. This equipment should be installed and operated with a minimum distance of 7.87 inches (20cm) between the radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. !CAUTIONDéclaration sur les limites d'exposition aux radiofréquences :cet équipement est conforme aux limites d'exposition aux rayonnements radioélectriques spécifiées par la FCC. Il doit être installé et utilisé à une distance minimale de 20 cm par rapport à votre corps pour les fréquences de 2,4 et 5 GHz. Cet émetteur-récepteur ne doit pas être utilisé ou situé à proximité d'autres antennes ou émetteurs-récepteurs. !CAUTIONThe device could automatically discontinue transmission in case of absence of information to transmit, or operational failure. Note that this is not intended to prohibit transmission of control or signaling information or the use of repetitive codes where required by the technology.!CAUTIONChanges or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.!CAUTIONToute modification effectuée sur cet équipement sans l'autorisation expresse de la partie responsable de la conformité est susceptible d'annuler son droit d'utilisation.
Aruba 203H Hospitality Access Points | Installation Guide 9CanadaComplies with the Class B limits for radio noise emissions as set out in the interference-causing equipment standard entitled “Digital Apparatus,” CAN ICES-3(B)/NMB-3(B).Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (E.I.R.P.) does not exceed the limit necessary for successful communication.This device complies with Industry Canada license-exempt RSS standard(s).Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Déclaration d’Industrie CanadaCet appareil numerique de la classe B respecte toutes les exigencies du Reglement sur le materiel brouilleur du Canada.Conformément aux réglementations d’Industrie Canada, cet émetteur-récepteur radio doit être utilisé uniquement avec une antenne dont le type et le gain maximal doivent être approuvés par Industrie Canada. Pour réduire les interférences radio potentielles, le type d’antenne et son gain doivent être choisis de façon à ce que la puissance isotrope rayonnée équivalente (PIRE) ne dépasse pas les valeurs nécessaires à une communication efficace. Ce périphérique est conforme aux règlements RSS exempts de licence d’Industrie Canada. L’utilisation de ce périphérique est soumise aux deux conditions suivantes : (1) ce périphérique ne doit pas provoquer d’interférences, et (2) ce périphérique doit accepter toute interférence, y compris les interférences susceptibles de provoquer un dysfonctionnement.EU Regulatory Conformance Aruba Networks Inc., hereby declares that this product is in compliance with the directives listed below:EMC Directive 2014Low Voltage Directive 2014R&TTE Directive 1999REACH Regulation (EC) No.: 1907/2006RoHS Directive 2011WEEE Directive 2012!CAUTIONThis equipment complies with IC RSS-102 RF exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body.!CAUTIONCet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.!CAUTIONUnder Industry Canada regulations, when operated in 5150 to 5250 MHz frequency range, this device is restricted to indoor use to reduce the potential for harmful interference with co-channel Mobile Satellite Systems. Users are advised that high power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850MHz and that these radars could cause interference and/or damage to LE-LAN devices.!CAUTIONConformément aux réglementations d’Industrie Canada, en cas d'utilisation dans la plage de fréquences de 5150 à 5250 MHz, cet appareil doit uniquement être utilisé en intérieur afin de réduire les risques d'interférence avec les systèmes satellites mobiles partageant le même canal. Les utilisateurs êtes avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu'ils ont la priorité) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL
10 Aruba 203H Hospitality Access Points | Installation GuideA Declaration of Conformity for these directives is available for viewing at www.arubanetworks.com.RF Warning해당무선설비는 전파혼신의 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없습니다Medical1. Equipment not suitable for use in the presence of flammable mixtures.2. Connect to only IEC 60950-1 or IEC 60601-1 3rd edition certified products and power sources. The end user is responsible for the resulting medical system complies with the requirements of IEC 60601-1 3rd edition.3. Wipe with a dry cloth, no additional maintenance required.4. No serviceable parts, the unit must be sent back to the manufacturer for repair.5. No modifications are allowed without Aruba approval.第十二條 →經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。第十四條 →低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。Proper Disposal of Aruba EquipmentDispose of Aruba products per local regulation. For the most current information about Global Environmental Compliance and Aruba products, visit www.arubanetworks.com.Waste of Electrical and Electronic EquipmentAruba products at end of life are subject to separate collection and treatment in the EU Member States, Norway, and Switzerland and therefore are marked with the symbol shown at the left (crossed-out wheelie bin). The treatment applied at end of life of these products in these countries shall comply with the applicable national laws of countries implementing Directive 2002/96/EC on Waste of Electrical and Electronic Equipment (WEEE).India RoHSThis product complies with RoHS requirements as prescribed by E-Waste (Management & Handling) Rules, governed by the Ministry of Environment & Forests, Government of India.European Union RoHSAruba products also comply with the EU Restriction of Hazardous Substances Directive 2011/65/EC (RoHS). EU RoHS restricts the use of specific hazardous materials in the manufacture of electrical and electronic equipment. Specifically, restricted materials under the RoHS Directive are Lead (including Solder used in printed circuit assemblies), Cadmium, Mercury, Hexavalent Chromium, and Bromine. Some Aruba products are subject to the exemptions listed in RoHS Directive Annex 7 (Lead in solder used in printed circuit assemblies). Products and packaging will be marked with the “RoHS” label shown at the left indicating conformance to this directive.China RoHSAruba products also comply with China environmental declaration requirements and are labeled with the “EFUP 10” label shown at the left.Expected Service Life 10 years. For additional compliance information, refer to the regulatory label on the back of this device.10ᴹᴹ∂ᴹᇣ⢙䍘༠᰾Hazardous Materials Declaration䜘Ԧ਽〠(Parts)ᴹ∂ᴹᇣ⢙䍘ᡆݳ㍐˄Hazardous Substance˅䫵˄Pb˅⊎˄Hg˅䭹˄Cd˅ޝԧ䬜˄Cr6+˅ཊⓤ㚄㤟˄PBB˅ཊⓤҼ㤟䟊˄PBDE˅⭥䐟⁑ඇ(circuit modules) XOOOO O⭥㔶৺⭥㔶㓴Ԧ(Cables & Cable Assemblies)OOOOO O䠁኎䜘Ԧ(Metal Parts) OOOOO Oກᯉ઼㚊ਸ⢙䜘Ԧ(Plastic and Polymeric Parts)OOOOO OO: 㺘⽪䈕ᴹ∂ᴹᇣ⢙䍘൘䈕䜘Ԧᡰᴹ൷䍘ᶀᯉѝⲴਜ਼䟿൷൘ SJ/T11363-2006 ḷ߶㿴ᇊⲴ䲀䟿㾱≲ԕлDŽIndicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ/T11363-2006 standard.X: 㺘⽪䈕ᴹ∂ᴹᇣ⢙䍘㠣ቁ൘䈕䜘ԦⲴḀа൷䍘ᶀᯉѝⲴਜ਼䟿䎵ࠪ SJ/T11363-2006 ḷ߶㿴ᇊⲴ䲀䟿㾱≲DŽIndicates that the concentration of the hazardous substance of at least one of all homogeneous materials in the parts is above the relevant threshold of the SJ/T11363-2006 standard.ሩ䬰୞ѻᰕⲴᡰ୞ӗ૱ˈᵜ㺘ᱮ⽪׋ᓄ䬮Ⲵ⭥ᆀؑ᚟ӗ૱ਟ㜭वਜ਼䘉Ӌ⢙䍘DŽThis table shows where these substances may be found in the supply chain of electronic informationproducts, as of the date of sale of the enclosed product. ↔ḷᘇѪ䪸ሩᡰ⎹৺ӗ૱Ⲵ⧟؍֯⭘ᵏḷᘇ.ḀӋ䴦䜘ԦՊᴹањн਼Ⲵ⧟؍֯⭘ᵏ(ֻྲ,⭥⊐অݳ⁑ඇ)䍤൘ަӗ૱к.↔⧟؍֯⭘ᵏ䲀ਚ䘲⭘Ҿӗ૱ᱟ൘ӗ૱᡻޼ѝᡰ㿴ᇊⲴᶑԦлᐕ֌.The Environment-Friendly Use Period (EFUP) for all enclosed products and their parts are per the symbol shown here. The Environment-Friendly Use Period is valid only when the product is operated under the conditions defined in the product manual.
www.arubanetworks.com3333 Scott BlvdSanta Clara, CA 9505411 Aruba 203H Hospitality Access Points | Installation GuideiContacting SupportCopyright© Copyright 2017 Hewlett Packard Enterprise Development LPOpen Source CodeThis product includes code licensed under the GNU General Public License, the GNU Lesser General Public License, and/or certain other open source licenses. A complete machine-readable copy of the source code corresponding to such code is available upon request. This offer is valid to anyone in receipt of this information and shall expire three years following the date of the final distribution of this product version by Hewlett Packard Enterprise Company. To obtain such source code, send a check or money order in the amount of US $10.00 to:Hewlett Packard Enterprise CompanyAttn: General Counsel3000 Hanover StreetPalo Alto, CA 94304USAWarrantyThis hardware product is protected by an Aruba warranty. For details, see Aruba Networks standard warranty terms and conditions.Main Site arubanetworks.comSupport Site support.arubanetworks.comAirheads Social Forums and Knowledge Base community.arubanetworks.comNorth American Telephone 1-800-943-4526 (Toll Free)1-408-754-1200International Telephones arubanetworks.com/support-services/contact-support/Software Licensing Site hpe.com/networking/supportEnd-of-life Information arubanetworks.com/support-services/end-of-lifeSecurity IncidentResponse Team (SIRT) Site: arubanetworks.com/support-service/security-bulletins/Email: sirt@arubanetworks.com
Aruba 203H Hospitality Access Points Regulatory Compliance and Safety Information GuideRev01 | December 2016 1IntroductionThis document contains domestic and international regulatory compliance and safety information for 203H access points. To ensure that this device complies with the regulatory standards for your region, please refer to the sections below.Electrical and Environmental SpecificationsRegulatory InformationProper Disposal of Aruba EquipmentElectrical and Environmental SpecificationsFor additional specifications on this product, please refer to the product data sheet at www.arubanetworks.com/safety_addendum.ElectricalEthernet:E0: Uplink network interface 100/1000 Base-T auto-sensing Ethernet RJ45 port.E1: Downlink network interface 100/1000 Base-T auto-sensing Ethernet RJ45 port.Power over Ethernet IEEE 802.3af 48VDCEnvironmentalOperating:Temperature: 0°C to +40°C (+32°F to +104°F)Humidity: 5% to 93% non-condensingStorage and transport:Temperature: -40°C to +70°C (-40°F to +158°F)Regulatory InformationThe regulatory model name for the 203H access point is APINH203.All Aruba access points should be professionally installed by an Aruba Certified Mobility Professional (ACMP). The installer is responsible for ensuring that grounding is available and meets applicable national and electrical codes.Tous les points d'accès Aruba doivent impérativement être installés par un professionnel agréé. Ce dernier doit s'assurer que l'appareil est mis à la terre et que le circuit de mise à la terre est conforme aux codes électriques nationaux en vigueur.
2Aruba 203H Hospitality Access Points | Regulatory Compliance and Safety Information GuideAruba Networks provides a multi-language document that contains country-specific restrictions and additional safety and regulatory information for all Aruba access points. This document can be viewed or downloaded at www.arubanetworks.com.FCCThis device is electronically labeled.To view the FCC ID for controller-managed access points:1. Log into the controller WebUI2. Navigate to Maintenance > Controller > AboutTo view the FCC ID for Instant access points:1. Log into the virtual controller WebUI2. Navigate to Maintenance > AboutFCC Class B Part 15This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 ofthe FCC Rules. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used inaccordance with the manufacturer’s instructions, may cause interference harmful to radio communications.Operation is subject to the following conditions:This device may not cause harmful interference.This device must accept any interference received, including interference that may cause undesired operation.If this equipment does cause interference, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver.Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.Consult the dealer or an experienced radio or TV technician for help.CanadaComplies with the Class B limits for radio noise emissions as set out in the interference-causing equipment standard entitled “Digital Apparatus,” CAN ICES-3(B)/NMB-3(B).Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (E.I.R.P.) does not exceed the limit necessary for successful communication.This device complies with Industry Canada license-exempt RSS standard(s).Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits. This equipment should be installed and operated with a minimum distance of 7.87 inches (20cm) between the radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Déclaration sur les limites d'exposition aux radiofréquences :cet équipement est conforme aux limites d'exposition aux rayonnements radioélectriques spécifiées par la FCC. Il doit être installé et utilisé à une distance minimale de 20 cm par rapport à votre corps pour les fréquences de 2,4 et 5 GHz. Cet émetteur-récepteur ne doit pas être utilisé ou situé à proximité d'autres antennes ou émetteurs-récepteurs. The device could automatically discontinue transmission in case of absence of information to transmit, or operational failure. Note that this is not intended to prohibit transmission of control or signaling information or the use of repetitive codes where required by the technology.Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Toute modification effectuée sur cet équipement sans l'autorisation expresse de la partie responsable de la conformité est susceptible d'annuler son droit d'utilisation.
Aruba 203H Hospitality Access Points | Regulatory Compliance and Safety Information Guide 3Déclaration d’Industrie CanadaCet appareil numerique de la classe B respecte toutes les exigencies du Reglement sur le materiel brouilleur du Canada.Conformément aux réglementations d’Industrie Canada, cet émetteur-récepteur radio doit être utilisé uniquement avec une antenne dont le type et le gain maximal doivent être approuvés par Industrie Canada. Pour réduire les interférences radio potentielles, le type d’antenne et son gain doivent être choisis de façon à ce que la puissance isotrope rayonnée équivalente (PIRE) ne dépasse pas les valeurs nécessaires à une communication efficace. Ce périphérique est conforme aux règlements RSS exempts de licence d’Industrie Canada. L’utilisation de ce périphérique est soumise aux deux conditions suivantes : (1) ce périphérique ne doit pas provoquer d’interférences, et (2) ce périphérique doit accepter toute interférence, y compris les interférences susceptibles de provoquer un dysfonctionnement.EU Regulatory Conformance Aruba Networks Inc., hereby declares that this product is in compliance with the directives listed below:EMC Directive 2014Low Voltage Directive 2014R&TTE Directive 1999REACH Regulation (EC) No.: 1907/2006RoHS Directive 2011WEEE Directive 2012A Declaration of Conformity for these directives is available for viewing at www.arubanetworks.com.EMC Class B Warning이 기기는 가정용 (B 급 ) 전자파적합기기로서 주로 가정에서 사용하는 것을 목적으로 하며 , 모든 지역에서 사용할 수 있습니다 .RF Warning해당무선설비는 전파혼신의 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없습니다Medical1. Equipment not suitable for use in the presence of flammable mixtures.2. Connect to only IEC 60950-1 or IEC 60601-1 3rd edition certified products and power sources. The end user is responsible for the resulting medical system complies with the requirements of IEC 60601-1 3rd edition.3. Wipe with a dry cloth, no additional maintenance required.4. No serviceable parts, the unit must be sent back to the manufacturer for repair.5. No modifications are allowed without Aruba approval.This equipment complies with IC RSS-102 RF exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body.Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.Under Industry Canada regulations, when operated in 5150 to 5250 MHz frequency range, this device is restricted to indoor use to reduce the potential for harmful interference with co-channel Mobile Satellite Systems. Users are advised that high power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850MHz and that these radars could cause interference and/or damage to LE-LAN devices.Conformément aux réglementations d’Industrie Canada, en cas d'utilisation dans la plage de fréquences de 5150 à 5250 MHz, cet appareil doit uniquement être utilisé en intérieur afin de réduire les risques d'interférence avec les systèmes satellites mobiles partageant le même canal. Les utilisateurs êtes avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu'ils ont la priorité) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL
© Copyright 2016 Hewlett Packard Enterprise Development LPwww.arubanetworks.com1344 Crossman AvenueSunnyvale, California 94089Phone: 408.227.4500Fax: 408.227.4550a Hewlett PackardEnterprise company4Aruba 203H Hospitality Access Points | Regulatory Compliance and Safety Information Guide第十二條 →經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。第十四條 →低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。Proper Disposal of Aruba EquipmentDispose of Aruba products per local regulation. For the most current information about Global Environmental Compliance and Aruba products, visit www.arubanetworks.com.Waste of Electrical and Electronic EquipmentAruba products at end of life are subject to separate collection and treatment in the EU Member States, Norway, and Switzerland and therefore are marked with the symbol shown at the left (crossed-out wheelie bin). The treatment applied at end of life of these products in these countries shall comply with the applicable national laws of countries implementing Directive 2002/96/EC on Waste of Electrical and Electronic Equipment (WEEE).India RoHSThis product complies with RoHS requirements as prescribed by E-Waste (Management & Handling) Rules, governed by the Ministry of Environment & Forests, Government of India.European Union RoHSAruba products also comply with the EU Restriction of Hazardous Substances Directive 2011/65/EC (RoHS). EU RoHS restricts the use of specific hazardous materials in the manufacture of electrical and electronic equipment. Specifically, restricted materials under the RoHS Directive are Lead (including Solder used in printed circuit assemblies), Cadmium, Mercury, Hexavalent Chromium, and Bromine. Some Aruba products are subject to the exemptions listed in RoHS Directive Annex 7 (Lead in solder used in printed circuit assemblies). Products and packaging will be marked with the “RoHS” label shown at the left indicating conformance to this directive.China RoHSAruba products also comply with China environmental declaration requirements and are labeled with the “EFUP 10” label shown at the left.Expected Service Life 10 years. For additional compliance information, refer to the regulatory label on the back of this device.10ᴹᴹ∂ᴹᇣ⢙䍘༠᰾Hazardous Materials Declaration䜘Ԧ਽〠(Parts)ᴹ∂ᴹᇣ⢙䍘ᡆݳ㍐˄Hazardous Substance˅䫵˄Pb˅⊎˄Hg˅䭹˄Cd˅ޝԧ䬜˄Cr6+˅ཊⓤ㚄㤟˄PBB˅ཊⓤҼ㤟䟊˄PBDE˅⭥䐟⁑ඇ(circuit modules) XOOOO O⭥㔶৺⭥㔶㓴Ԧ(Cables & Cable Assemblies)OOOOO O䠁኎䜘Ԧ(Metal Parts) OOOOO Oກᯉ઼㚊ਸ⢙䜘Ԧ(Plastic and Polymeric Parts)OOOOO OO: 㺘⽪䈕ᴹ∂ᴹᇣ⢙䍘൘䈕䜘Ԧᡰᴹ൷䍘ᶀᯉѝⲴਜ਼䟿൷൘ SJ/T11363-2006 ḷ߶㿴ᇊⲴ䲀䟿㾱≲ԕлDŽIndicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ/T11363-2006 standard.X: 㺘⽪䈕ᴹ∂ᴹᇣ⢙䍘㠣ቁ൘䈕䜘ԦⲴḀа൷䍘ᶀᯉѝⲴਜ਼䟿䎵ࠪ SJ/T11363-2006 ḷ߶㿴ᇊⲴ䲀䟿㾱≲DŽIndicates that the concentration of the hazardous substance of at least one of all homogeneous materials in the parts is above the relevant threshold of the SJ/T11363-2006 standard.ሩ䬰୞ѻᰕⲴᡰ୞ӗ૱ˈᵜ㺘ᱮ⽪׋ᓄ䬮Ⲵ⭥ᆀؑ᚟ӗ૱ਟ㜭वਜ਼䘉Ӌ⢙䍘DŽThis table shows where these substances may be found in the supply chain of electronic informationproducts, as of the date of sale of the enclosed product. ↔ḷᘇѪ䪸ሩᡰ⎹৺ӗ૱Ⲵ⧟؍֯⭘ᵏḷᘇ.ḀӋ䴦䜘ԦՊᴹањн਼Ⲵ⧟؍֯⭘ᵏ(ֻྲ,⭥⊐অݳ⁑ඇ)䍤൘ަӗ૱к.↔⧟؍֯⭘ᵏ䲀ਚ䘲⭘Ҿӗ૱ᱟ൘ӗ૱᡻޼ѝᡰ㿴ᇊⲴᶑԦлᐕ֌.The Environment-Friendly Use Period (EFUP) for all enclosed products and their parts are per the symbol shown here. The Environment-Friendly Use Period is valid only when the product is operated under the conditions defined in the product manual.

Navigation menu