Hewlett Packard Enterprise APINR108109 Wireless Access Point User Manual

Aruba Networks, Inc. Wireless Access Point

Contents

Installation Guide

Aruba RAP-108 and RAP-109 Remote Access PointInstallation GuideThe Aruba RAP-108 and RAP-109 are dual-radio, dual-band remote access points that supports the IEEE 802.11n standard for high-performance WLAN. These access point uses MIMO (Multiple-in, Multiple-out) technology and other high-throughput mode techniques to deliver high-performance, 802.11n 2.4 GHz and 5 GHz functionality while simultaneously supporting existing 802.11a/b/g wireless services. The RAP-108/RAP-109 ships with Aruba Instant software. Therefore, out of the box, the RAP-108/RAP-109 will operate as a Virtual Controller (VC) or an Instant AP. However, the RAP-108/RAP-109 can be converted to operate as a Remote AP (RAP). For information about the IAP to RAP conversion, see RAP Conversion.The Aruba RAP-108/RAP-109 remote access point provides the following capabilities:Wireless transceiverProtocol-independent networking functionalityIEEE 802.11a/b/g/n operation as a wireless access pointIEEE 802.11a/b/g/n operation as a wireless air monitorCompatibility with IEEE 802.3af and 802.3at Package ContentsRAP-108 or RAP-109 Remote Access PointRAP-108/RAP-109 Mounting StandInstallation GuideRAP-108/RAP-109 Hardware OverviewFigure 1 Ports Reset ButtonThe reset button can be used to return the AP to factory default settings. To reset the AP:1. Power off the AP.2. Press and hold the reset button using a small, narrow object, such as a paperclip.3. Power-on the AP without releasing the reset button. The power LED will flash within 5 seconds.4. Release the reset button.The power LED will flash again within 15 seconds indicating that the reset is completed. The AP will now continue to boot with the factory default settings.USB InterfaceThe RAP-108/RAP-109 is equipped with a USB interface for connectivity with cellular modems. Console PortUse the console port to connect to a terminal for direct local management.ENET 0For primary network connectivity, RAP-108/RAP-109 is equipped with a 10/100/1000BASE-T (RJ-45) auto-sensing, MDI/MDX Gigabit Ethernet port. This port supports IEEE 802.3af Power over Ethernet (PoE) compliance, accepting 48VDC as a standard defined Powered Device (PD) from a Power Sourcing Equipment (PSE) such as a PoE midspan injector, or network infrastructure that supports PoE.ENET 1For secondary network connectivity, RAP-108/RAP-109 is equipped with a 10/100BASE-T (RJ-45) auto-sensing, MDI/MDX Fast Ethernet port.DC Power SocketIf PoE is not available, an optional Aruba AP AC-DC adapter kit (sold separately) can be used to power the RAP-108/RAP-109. External Antenna Connectors (RAP-108 Only)The RAP-108 is equipped with two RP-SMA external antenna connectors and requires the use of two dual-band antennas. These ports are marked ANT0 and ANT1, matching radio chains 0 and 1.In order to ensure accurate RF power level setting and reporting in software, as well as compliance with any regulatory restrictions, the correct gain for antennas used (adjusted for any additional cabling loss, if applicable) needs to be entered in software when provisioning the RAP-108. Two antenna gain numbers are needed for this; one for each supported band (2.4GHz and 5GHz). These numbers can be obtained from the antenna datasheet or specifications. Antenna gain for RAP-109 is hardcoded to the correct values already, so there is no need for any additional action on that platform.Figure 2 LEDs LEDsPWR: Indicates whether or not the RAP-108/RAP-109 is powered-onENET0 and ENET1: Indicates the status of the RAP-108/RAP-109’s Ethernet ports5 GHz: Indicates the status of the 802.11a/n radio2.4 GHz: Indicates the status of the 802.11b/g/n radioInstalling the APTabletop MountingThe RAP-108/RAP-109 is shipped with a stand to use on flat (i.e. table top) surfaces. Place the RAP-108/RAP-109 in the stand (see Figure 3) and place the stand on a flat, level surface. To attach the RAP to the stand:1. Align the center peg of the stand with recessed hole on the unit.2. Align the mounting posts on the back of the AP with corresponding openings on the stand.3. Rotate the AP clockwise until it clicks into place.Figure 3 Stand Installation Connecting the Required CablesThe RAP-108/RAP-109 must be connected to a network device that has access to the Internet, such as a router or modem. To complete the installation of the RAP-108/RAP-109:1. Connect one end of the provided RJ-45 cable to port E0 on the RAP-108/RAP-109.2. Connect the other end of the RJ-45 cable to a free RJ-45 port on your modem or router. 3. Attach the provided power adapter to the DC IN port on the RAP-108/RAP-109.4. Connect the other end of the power adapter to a power outlet.The RAP-108/RAP-109 is now powered on. To verify this, ensure that the PWR LED is solid green. Verifying Successful InstallationOnce the RAP-108/RAP-109’s PWR LED has come up, the device will take 2 to 3 minutes to complete the boot cycle. Once the boot cycle is complete, you can connect to your company or corporate network.RAP ConversionIf your network administrator has instructed you to convert the RAP-108/RAP-109 to work in RAP mode, follow the process below to complete the RAP conversion. 1. Power up the RAP-108/RAP-109.2. Connect to Instant SSID.3. Login to the RAP-108/RAP-109 by navigating to http://instant.arubanetworks.com and login to the Instant WebUI. The default username is admin and the default password is admin. See the included Aruba Instant Quick Start Guide for more information.4. Navigate to the Maintenance tab in the top right.5. Click on the Convert tab.6. Select Remote APs managed by a Mobility Controller from the drop down menu.7. Enter the IP address of the controller. This is provided by your network administrator.8. Click Convert Now to complete the conversion (see Figure 4).9. The RAP-108/RAP-109 will reboot and begin operating in RAP mode.Figure 4 IAP-RAP Conversion over the InternetThe RAP-108/RAP-109 requires Aruba Instant 3.2 or ArubaOS 6.2.Inform your supplier if there are any incorrect, missing, or damaged parts. If possible, retain the carton, including the original packing materials. Use these materials to repack and return the unit to the supplier if needed.The USB interface is disabled when the RAP-108/RAP-109 is powered from 802.3af PoE.ENET 1ENET 056V 350mA1.25ACONSOLETable 1 RAP-108/RAP-109 Series LED Meanings LED Color/State MeaningPWR Off No power to APRed steady System initializingGreen flashing Device booting, not readyGreen steady Device readyENET0 Off No linkAmber 10/100 Mbps linkGreen 1000 Mbps linkFlashing Ethernet link activityENET1 Off No linkGreen 10/100 Mbps linkFlashing Ethernet link activity5 GHz Off 5 GHz radio is disabledAmber steady 5 GHz radio enabled in WLAN modeGreen steady 5 GHz radio enabled in 11n modeGreen flashing 5 GHz Air Monitor mode2.4 GHz5 GHzENET 1ENET 0PWR2.4 GHz Off 2.4 GHz radio disabledAmber steady 2.4 GHz radio enabled in WLAN modeGreen steady 2.4 GHz radio enabled in 11n modeGreen flashing 2.4 GHz Air Monitor modeTable 1 RAP-108/RAP-109 Series LED Meanings (Continued)LED Color/State MeaningRAP-108_02
Aruba RAP-108 and RAP-109 Remote Access PointInstallation Guidewww.arubanetworks.com1344 Crossman AvenueSunnyvale, California 94089Phone: 408.227.4500Fax 408.227.4550Aruba RAP-108 and RAP-109 Remote Access Point | Installation GuidePart Number 0511191-01 | November 2012Contacting Aruba NetworksTable 1 Web Site SupportMain Site http://www.arubanetworks.com Support Site https://support.arubanetworks.com Software Licensing Site https://licensing.arubanetworks.com/login.phpWireless Security IncidentResponse Team (WSIRT) http://www.arubanetworks.com/support/wsirt.phpAmericas and APAC Support Email support@arubanetworks.com EMEA Support Email emea.support@arubanetworks.comWSIRT EmailPlease email details of any securityproblem found in an Aruba product.wsirt@arubanetworks.comTable 2 Telephone SupportAruba Corporate +1 (408) 227-4500FAX +1 (408) 227-4550Copyright© 2010 Aruba Networks, Inc. AirWave®, Aruba Networks®, Aruba Mobility Management System®, Bluescanner, For Wireless That Works®, Mobile Edge Architecture, People Move. Networks Must Follow., RFProtect®, The All Wireless Workplace Is Now Open For Business, and The Mobile Edge Company® are trademarks of Aruba Networks, Inc. All rights reserved. All other trademarks are the property of their respective owners.Open Source CodeCertain Aruba products include Open Source software code developed by third parties, including software code subject to the GNU General Public License ("GPL"), GNU Lesser General Public License ("LGPL"), or other Open Source Licenses. The Open Source code used can be found at this site:http://www.arubanetworks.com/open_sourceLegal NoticeThe use of Aruba Networks, Inc. switching platforms and software, by all individuals or corporations, to terminate other vendors' VPN client devices constitutes complete acceptance of liability by that individual or corporation for this action and indemnifies, in full, Aruba Networks, Inc. from any and all legal actions that might be taken against it with respect to infringement of copyright on behalf of those vendors.WarrantyThis hardware product is protected by the standard Aruba warranty of one year parts/labor. For more information, refer to the ARUBACARE SERVICE AND SUPPORT TERMS AND CONDITIONS.Altering this device (such as painting it) voids the warranty.Product SpecificationsElectricalEthernet:1 x 10/100/1000Base-T auto-sensing Ethernet RJ-45 Interface1x 10/100Base-T auto-sensing Ethernet RJ-45 InterfaceMDI/MDXIEEE 802.3 (10Base-T), IEEE 802.3u (100Base-T). IEEE 802.3ab (1000Base-T)Power over Ethernet (IEEE 802.3af and 802.3at compliant), 56V DC/350mAPower: 12 VDC power interface, supports powering through an AC-to-DC power adapterFor additional specifications on this product, please refer to the data sheet. The data sheet can be found at www.arubanetworks.com.Proper Disposal of Aruba EquipmentFor the most current information about Global Environmental Compliance and Aruba products, see our website at www.arubanetworks.com.Waste of Electrical and Electronic EquipmentAruba products at end of life are subject to separate collection and treatment in the EU Member States, Norway, and Switzerland and therefore are marked with the symbol shown at the left (crossed-out wheelie bin). The treatment applied at end of life of these products in these countries shall comply with the applicable national laws of countries implementing Directive 2002/96EC on Waste of Electrical and Electronic Equipment (WEEE).European Union RoHSAruba products also comply with the EU Restriction of Hazardous Substances Directive 2002/95/EC (RoHS). EU RoHS restricts the use of specific hazardous materials in the manufacture of electrical and electronic equipment. Specifically, restricted materials under the RoHS Directive are Lead (including Solder used in printed circuit assemblies), Cadmium, Mercury, Hexavalent Chromium, and Bromine. Some Aruba products are subject to the exemptions listed in RoHS Directive Annex 7 (Lead in solder used in printed circuit assemblies). Products and packaging will be marked with the “RoHS” label shown at the left indicating conformance to this Directive.China RoHSAruba products also comply with China environmental declaration requirements and are labeled with the “EFUP 10” label shown at the left.Safety and Regulatory ComplianceAruba Networks provides a multi-language document that contains country-specific restrictions and additional safety and regulatory information for all Aruba access points. This document can be viewed or downloaded from the following location: www.arubanetworks.com/safety_addendum Regulatory Model NamesThe following regulatory model names apply to the RAP-108/109:RAP-108: APINR108 RAP-109: APINR109EMC Compliance and Warning StatementIEC 60601-1-2: 2007 EN 60601-1-2: 2007 This equipment has been tested and found to comply with the limits of the standard for medical devices, IEC 60601-1-2:2007. The unit also complies with the requirements of EN 60601-1-2:2007, providing the presumption of compliance to the European Union’s Medical Device Directive 2007/47/EC. The limits are designed to provide reasonable protection against harmful interference in a typical medical installation. This equipment generates, uses and can radiate radio frequency energy, and, if not installed and used in accordance with the manufacturer’s instructions may cause harmful interference to other devices in the vicinity. However, there is no guarantee that interference will not occur in a particular installation. If this equipment causes interference with other devices, which may be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:Reorient or relocate the device receiving the interference.Increase the separation between the equipment.Connect the equipment into an outlet on a circuit different from that to which the other device(s) are connected.Consult the manufacturer or field service technician for help.The Models APINR108 and APINR109 do not have an Applied Part as defined in IEC 60601-1. The protection against electric shock is Class ll. Device is not protected against ingress of liquids and has a protection class of IPX0 as defined by IEC 60601-1 and IEC 60529. Equipment not suitable for use in the presence of flammable mixtures.The unit is considered “Continuous Operation” equipment as defined by IEC 60601-1. Power Consumption – 56 VDC 802.3at power over Ethernet or 12VDC, 1.25A for external AC supplied power (adapter sold separately); Maximum power consumption - 12.5W (without USB device connected); 15W (with USB device connected). Mechanical Dimensions: 160mm x 160mm x 41mm; 300g.Environmental: Operating Temp: 0° C to +40° C (+32° F to +104° F); Humidity: 5 to 95% non-condensing. Storage Temp: -40° CS to +70° C (-40°F to +158°F).If a power adapter other than the one provided by Aruba Networks is used in the US or Canada, it should be cULus (NRTL) Listed, with an output rated 12 VDC, minimum 1.25A, marked “LPS” or “Class 2,” and suitable for plugging into a standard power receptacle in the US and Canada.!Aruba access points must be installed by a professional installer. The professional installer is responsible for ensuring that grounding is available and it meets applicable local and national electrical codes.10!ѻકݙ৿ॅᆇ⠽䋼ᧁ䴆㸼䳊䚼ӊৡ⿄䳊䚼ӊৡ⿄䳊䚼ӊৡ⿄䳊䚼ӊৡ⿄ॅᆇ⠽䋼乍Ⳃ䪙䪙䪙䪙䬝䬝䬝䬝∲∲∲∲݁Ӌ䫀݁Ӌ䫀݁Ӌ䫀݁Ӌ䫀PBB PBDE(Pb) (Cd) (Hg) (Cr6+)(໮⒈໮⒈໮⒈໮⒈㘨㣃㘨㣃㘨㣃㘨㣃)(໮⒈໮⒈໮⒈໮⒈Ѡ㣃ЭѠ㣃ЭѠ㣃ЭѠ㣃Э䝮䝮䝮䝮) ৿䡙ঞ䣐ᴤ䞥ቀӊ Øƻ ƻ ƻ ƻ ƻ৿⦏⩗⬉䰏 Øƻ ƻ ƻ ƻ ƻ催⏽䫵ᴤ Øƻ ƻ ƻ ƻ ƻƻ˖㸼⼎ℸ䚼ӊՓ⫼ⱘ᠔᳝ৠ㉏ᴤ᭭Ёℸ⾡᳝↦៪᳝ᆇ⠽䋼ⱘ৿䞣ഛԢѢ SJ/T11363-2006 㾘ᅮⱘ䰤ࠊ㽕∖DŽ Ø˖㸼⼎ℸ䚼ӊՓ⫼ⱘ㟇ᇥϔ⾡ৠ㉏ᴤ᭭Ёˈℸ⾡᳝↦៪᳝ᆇ⠽䋼ⱘ৿䞣催Ѣ SJ/T11363-2006 㾘ᅮⱘ䰤ࠊ㽕∖DŽ !RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. !When operated in the 5.15 to 5.25 GHz frequency range, this device is restricted to indoor use to reduce the potential for harmful interference with co-channel Mobile Satellite Systems.

Navigation menu