Hewlett Packard Enterprise ARUBA60 802.11 .a/.b/.g Access Point User Manual

Aruba Networks, Inc. 802.11 .a/.b/.g Access Point

Contents

User Manual Chp 3 App

AP Deployment 23Chapter 3CHAPTER 3AP DeploymentThis chapter covers the following topics:zPhysical mounting of the Aruba 60/61zConnecting the required cablesMounting the Aruba 60/61When provisioning is complete, mount the Aruba 60/61 at its intended service location.The Aruba 60/61 Access Points with or without external antennas are intended only for installation in Environment A as defined in IEEE 802.3.af. All interconnected equipment must be contained within the same building, including the interconnected equipment's associated LAN connections.Select a location as close as possible to the center of the intended coverage area. If necessary, use the Aruba RF Plan site survey tool to determine the optimum locations for your access points and air monitors.The service location should be free from obstructions or obvious sources of interference. Normally, the higher you place an access point or air monitor, the better its performance.If external antennas are used, make sure that they and their associated wiring are located entirely indoors. TheAruba 60/61 and any optional external antennas are not suitable for outside use.
24 Aruba 60/61 Part 0500034Installation Guide July 2004The Aruba 60/61 can be mounted on a wall or suspended from above (not shown) using one of the optional mounting kits (dimensions vary) in the following ways:FIGURE 3-1 Aruba 60/61 Mounting OptionsNote For dimensions, see “Product Specifications”. Allow 5 cm (2") additional space on the right-hand side for cables. Measurements for the Aruba AP60 depend on attached antennas, which vary.Aruba AP60 Detachable AntennasBefore deploying the Aruba AP60, attach the appropriate antennas (not included). The antenna connections should be tightened by hand to avoid overtightening.The Aruba AP60 has dual Reverse Polarity SMA (RP-SMA) female antenna connectors that accept a variety of high-gain detachable antennas. A list of antennae tested for use with the Aruba AP60 is available on the Aruba Wireless Networks Web site:http://www.arubanetworks.comCheck the Interoperability section of the Products page for the latest information.Note Other antennae not listed may also work with the Aruba AP60, but for RF regulatory purposes should only be used if they are rated at a lower gain than similar, listed antennae.1 2 3
AP Deployment 25Chapter 3Make sure that all external antennas and their associated wiring are located entirely indoors. The Aruba AP60 Access Points and their optional external antennas are not suitable for outside use.Free-Standing PlacementTo place the Aruba 60/61 indoors on a flat table or shelf:1 Flip open the stand located on the back of the Aruba 60/61:FIGURE 3-2 Aruba 60/61Fold-Out Stand2 Place the device on a sturdy table or shelf.3 Orient the antennas.For best performance, swivel the individual antennas (Aruba AP60) or antenna array (Aruba AP61) so that they are oriented vertically. Once mounting is complete, connect the required cables (see instructions on page 28).CAUTION—Do not place the Aruba 60/61 in any place where it could fall on people or equipment. For more secure installation, use one of the optional mounting kits.
26 Aruba 60/61 Part 0500034Installation Guide July 2004Using the Built-In Mounting SlotsThe keyhole-shaped slots on the back of the Aruba 60/61 can be used to attach the device upright to an indoor wall or shelf.To hang the Aruba 60/61 upright using the mounting slots, perform the following steps.1 Install two screws in the wall or shelf as shown in Figure 3-3:FIGURE 3-3 Mounting Screw SpecificationsIf attaching the device to drywall, we recommend using appropriate wall anchors (not included) as shown in Figure 3-4 on page 27.CAUTION—Do not use the mounting slots to hang the Aruba 60/61 from the ceiling, sideways, or in any place where it could fall on people or equip-ment. For more secure installation, use one of the optional mounting kits.Screw/Nail Positions(fastened to wall or shelf)12.7 cm(5.00")0.12"0.27"0.23"0.05"clearance from surface3.0 mm5.8 mm0.08"0.15"clearance from surface2.0 mm3.8 mmclearance from surface1.3 mmclearnace from surface7.0 mmMaximum MinimumScrew/Nail Dimensions
AP Deployment 27Chapter 32 Align the Aruba 60/61 mounting slots to capture the surface screws.FIGURE 3-4 Hanging the Aruba 60/61 on Screws3 Secure the Aruba 60/61, if desired.To prevent the unauthorized removal of the Aruba 60/61 from its installed location, use a Kensington MicroSaver Security Cable (not included). Wrap the security cable around an immovable object, insert the cable’s lock into the Kensington Security Slot on the back of the Aruba 60/61, and turn the key.4 Orient the antennas.For best performance, swivel the individual antennas (Aruba AP60) or antenna array (Aruba AP61) so that they are oriented vertically (see Figure 3-1 on page 24). Once mounting is complete, connect the required cables (see instructions on page 28).Using the Optional Mounting KitsUse the optional mounting kit to attach the Aruba 60/61 to a wall, shelf, or ceiling. For installation, see the Aruba AP60/61 Mounting Kit Installation Notes (P/N 0500037-01) provided with each kit.
28 Aruba 60/61 Part 0500034Installation Guide July 2004Connecting Required CablesThe Aruba 60/61 Access Points with or without external antennas are intended only for installation in Environment A as defined in IEEE 802.3.af. All interconnected equipment must be contained within the same building, including the interconnected equipment's associated LAN connections.Selecting an FE CableThe 10/100 Mbps Ethernet (FE) port is used to connect the AP to a 10Base-T/100Base-TX (twisted-pair) Ethernet LAN segment. The appropriate FE cable depends on the features required of the FE port:zSPOEWhen connecting the AP to a device that supports Serial and Power Over Ethernet (SPOE), use an 8-conductor, Category 5 UTP, straight-through FE cable.The Aruba 5000 (with Line Card LC-5000-24FE-2GE-SPOE), the Aruba 2400, and the Aruba 800 support SPOE.zPOEIf the connecting device supports only Power Over Ethernet (POE), use a 4- or 8-conductor, Category 5 UTP, straight-through FE cable.zNetwork OnlyIf the connecting device does not support POE, use a 4- or 8-conductor, Category 5 UTP, FE cable. The port detects MDI/MDX and automatically adjusts for straight-through or crossover cables.The maximum length for FE cables is 100 meters (325 feet).When the Aruba 60/61 is installed in an air-handling space, as described in NEC (2002) Article 300.22(C), POE is required. Also, any FE cable installed in such spaces should be suitable under NEC Article 800.50 and marked accordingly for use in plenums and air-handling spaces with regard to smoke propagation, such as CL2-P, CL3-P, MPP or CMP.Install cables in accordance with all applicable local regulations and practices.For more port and cable details, see Appendix A.
AP Deployment 29Chapter 3Connecting Cables & Power1 Connect one end of the FE cable directly to the Aruba 60/61 FE port.2 Connect the other end of the FE cable to one of the following:To a network port on the Aruba WLAN Switch, orTo a network hub, router, or switch that has a routable path to the Aruba WLAN Switch.Note If the connecting device supplies POE, a straight-through cable must con-nect the Aruba 60/61 directly to the powering device without any interven-ing hubs, routers, or other networking equipment.3 Connect power, if necessary.The Aruba 60/61 can receive electrical power using the following options:zPOEIf connecting the Aruba 60/61 to a device that supplies IEEE 802.3af compliant POE no additional power connection is necessary.zPower OutletNote When the Aruba 60/61 is installed in an air-handling space, as described in NEC (2002) Article 300.22(C), POE must be used instead of a power outlet.CAUTION—To prevent personal injury or damage to equipment, be sure to comply with electrical grounding standards during all phases of installation and operation of the AP. Do not allow the Aruba 60/61 or its attachments to be connected to or make contact with metal or power outlets on a different electrical ground than the device to which it is connected. Also, never con-nect the AP or WLAN Switch to external storm grounding sources.AB
30 Aruba 60/61 Part 0500034Installation Guide July 2004If local regulations and practices permit, connect the optional AC power adapter (not included) to the DC power socket on the Aruba 60/61 and plug it into an appropriate power outlet.CAUTION—To prevent personal injury or damage to equipment, use only the AC power adapter certified for this device in the country where it is used.
Port Specifications 31Appendix AAPPENDIX APort SpecificationsFE PortThe 10/100 Mbps Ethernet (FE) port is located on the right-hand side of the Aruba 60/61 and has an RJ-45 female connector. The port pin-outs are shown in Figure A-1 :FIGURE A-1 Aruba 60/61 FE PortThe appropriate cable depends on the level of connectivity required of the FE port:zIf the connecting device supports Serial and Power Over Ethernet (SPOE), use an 8-conductor, Category 5 UTP, straight-through FE cable with a male RJ-45 connector.The Aruba 5000 (with Line Card LC-5000-24FE-2GE-SPOE), the Aruba 2400, and the Aruba 800 support SPOE.zIf the connecting device supports only Power Over Ethernet (POE, including IEEE 802.3af POE as well as “inline” or “midspan” POE devices), use an 8- or 4-conductor, Category 5 UTP, straight-through FE cable with male RJ-45 connectors.zIf the connecting device does not support Serial or POE, use a 4- or 8-conductor, Category 5 UTP, FE cable with male RJ-45 connectors. The port detects MDI/MDX and automatically adjusts for straight-through or crossover cables.Aruba 60/6110/100 Mbps EthernetRJ-45 FemalePin-Out*POE optional**Serial optionalSerial TxD**Serial TGND**Serial RxD**Serial RGND**12345678ETH Rx+ (POE negative*)ETH Rx– (POE negative*)ETH Tx+ (POE positive*)ETH Tx– (POE positive*)DirectionInputOutput
32 Aruba 60/61 Part 0500034Installation Guide July 2004The maximum length for FE cables is 100 meters (325 feet). When the Aruba 60/61 is installed in an air-handling space, as described in NEC (2002) Article 300.22 (C), POE is required. Also, any FE cable installed in such spaces should be suitable under NEC Article 800.50 and marked accordingly for use in plenums and air-handling spaces with regard to smoke propagation, such as CL2-P, CL3-P, MPP or CMP.Install cables in accordance with all applicable local regulations and practices.Serial Breakout AdapterThe optional serial breakout adapter is used to separate the serial communications lines from the Aruba 60/61 FE+SPOE port. This allows the administrator to connect a local serial console directly to the AP and access the apboot prompt for manual provisioning.The serial breakout adapter pin-outs are shown in Figure A-2 :FIGURE A-2 Aruba Serial Breakout AdapterRJ-45 Male "To Network" Pin-Out12345678ETH Rx+ (POE negative)ETH Rx– (POE negative)ETH Tx+ (POE positive)ETH Tx– (POE positive)Serial TxDSerial TGNDSerial RxDSerial RGNDRJ-45 Male "To AP" Pin-Out12345678ETH Rx+ (POE positive)ETH Rx– (POE positive)ETH Tx+ (POE negative)ETH Tx– (POE negative)RxDTxDSG543219876DB-9 Female Pin-OutInputOutputDirection 1234567891234567812345678Internal Adapter Wiring"To AP""To Network"To Console
Port Specifications 33Appendix ADB-9 SpecificationThe DB-9 connector attaches to the serial port of a console terminal. Communication settings for the port are specified in Table A -1 :“To AP” SpecificationsThe RJ-45 connector labeled “To AP” attaches to the Aruba 60/61 FE port either directly (if the AP is physically available) or indirectly (if the AP is already deployed).When connecting indirectly, use a straight-through FE coupler to attach the “To AP” connector to the FE cable leading directly to the AP’s FE port with no intervening hubs, routers, or other network equipment. The cable must be 8-conductor, Category 5 UTP, straight-through FE cable with a maximum length of 100 meters (325 feet).The Aruba 60/61 and serial breakout adapter are plenum rated. When is installed in an air-handling space, as described in NEC (2002) Article 300.22(C), any connecting FE cable should be suitable under NEC Article 800.50 and marked accordingly for use in plenums and air-handling spaces with regard to smoke propagation, such as CL2-P, CL3-P, MPP or CMP.Install cables in accordance with all applicable local regulations and practices.“To Network” SpecificationsThe RJ-45 connector labeled “To Network” attaches to an FE LAN segment. This connection is optional unless IEEE 802.11af Power Over Ethernet (POE) is used to power the AP during manual provisioning.A straight-through FE coupler may be used to attach the “To Network” connector to a LAN FE cable. The appropriate cable depends on the level of connectivity required of the FE port:zIf the connecting device supports IEEE 802.3af Power Over Ethernet (POE), use a 4- or 8-conductor, Category 5 UTP, straight-through FE cable with male RJ-45 connectors.The Aruba 5000 (with Line Card LC-5000-24FE-2GE-SPOE), the Aruba 2400, and the Aruba 800 support SPOE.zOtherwise, use a 4- or 8-conductor, Category 5 UTP, FE cable with male RJ-45 connectors. The port detects MDI/MDX and automatically adjusts for straight-through or crossover cables.TABLE A-1 Console Terminal SettingsBaud Rate Data Bits Parity Stop Bits Flow Control9600 8 None 1 None
34 Aruba 60/61 Part 0500034Installation Guide July 2004Note Only IEEE 802.3af Power Over Ethernet is supported for manual provi-sioning. “Inline” or “midspan” POE devices will not work with the Aruba serial breakout adapter.The maximum length for FE cables is 100 meters (325 feet).The Aruba 60/61 and serial breakout adapter are plenum rated. When is installed in an air-handling space, as described in NEC (2002) Article 300.22(C), the connecting FE cable should be suitable under NEC Article 800.50 and marked accordingly for use in plenums and air-handling spaces with regard to smoke propagation, such as CL2-P, CL3-P, MPP or CMP.Install cables in accordance with all applicable local regulations and practices.
Troubleshooting 35Appendix BAPPENDIX BTroubleshootingAfter provisioning and deployment, the Aruba 60/61 can be configured and managed through the Aruba WLAN Switch. However, the Aruba 60/61 includes built-in troubleshooting fea-tures for situations where the switch commands are unable to diagnose AP problems.This appendix describes using the built-in AP support prompt for troubleshooting.Accessing the AP Support PromptDepending on your network topology, the built-in AP Support prompt can be accessed using the AP serial console port or through the WLAN switch using the Serial Over Ethernet (SOE) interface or using Telnet from a remote management station.Direct SPOE Connection to WLAN SwitchThis method requires that the Aruba 60/61 is connected directly to an SPOE-compatible net-work port on the Aruba WLAN Switch (see “Connecting Required Cables” on page 28).1 Telnet to the Aruba WLAN Switch Serial-Over-Ethernet (SOE) interface.Use a Telnet client on your management workstation to connect to theAruba WLAN Switch IP address using logical port 2300. The connection command may vary depending on the specific software used, but commonly appears as follows:> telnet <WLAN switch IP address> 2300
36 Aruba 60/61 Part 0500034Installation Guide July 20042 When prompted, log in to the Aruba WLAN Switch as the administrator:This will present you with the Aruba WLAN Switch SOE console prompt:3 Connect to the Aruba WLAN Switch port to which the Aruba 60/61 is physically attached:where slot number is the physical slot of the line card in the WLAN switch, and port number is the physical port.If the AP has not finished booting, allow the Autoboot timer to expire. When the device has booted, the AP support prompt (#) will appear.Direct Terminal ConnectionThis method requires that the Aruba 60/61 is connected to a compatible serial console using the Aruba serial breakout adapter (see “Connecting the Console Terminal” on page 15).1 Set up your local terminal.This procedure requires a terminal or computer running terminal emulation software with the following settings:2 Establish console communication.Press <Enter> a few times to establish communication between the Aruba 60/61 and termi-nal.If the AP has not finished booting, allow the Autoboot timer to expire. When the device has booted, the AP Support prompt (#) will appear.user: adminpassword: <administrator password (not displayed)>Available commands: baud [9600|19200|38400|57600|115200] connect <slot/port> exit (no args)soe>soe> connect <slot number>/<port number>Ta b l e 3 - 1 Console Terminal SettingsBaud Rate Data Bits Parity Stop Bits Flow Control9600 8 None 1 None
Troubleshooting 37Appendix BRemote Telnet ConnectionIf properly set up, the AP support prompt can be accessed remotely using Telnet. By default, this feature is turned off for security purposes and cannot be turned on using the AP interface.Setting Telnet AccessTelnet access can only be changed from the WLAN switch management interface. Log in to the WLAN switch CLI using the admin account, access the configuration (config) prompt, and issue the following commands:Using Telnet to ConnectUse a Telnet client on your management workstation to connect to the Aruba 60/61’s individ-ual IP address. The connection command may vary depending on the specific software used, but commonly appears as follows:When the connection is established, the AP support prompt (#) will be displayed.(Aruba 5000) (config) # ap location <building>.<floor>.<device>(Aruba 5000) (sap-config location b.f.d) # telnet {enable|disable}> telnet <Aruba 60/61 IP address>
38 Aruba 60/61 Part 0500034Installation Guide July 2004AP SupportAccess LevelszUser AccessUser access is a low security level, featuring only the most basic commands. It is available without any additional login after the AP has booted.zPrivileged AccessPrivileged-level access requires the privileged password (the same privileged password used on the switch) to be entered using the user level enable command. The privileged access level is available only after the AP has successfully booted and synchronized with WLAN switch.User Commandszping <host|IP address>Verify IP connectivity between the AP and the host address.zrouteDisplay the contents of the AP route table.zifconfigDisplay the AP’s IP address settings.zenable <privileged password>Access the AP Support privileged mode.Privileged CommandsIn addition to the user commands, the following commands are available upon successfully entering the privileged mode:zpszshow [config|stats|version]Note— These commands should be used only as directed by Aruba Customer Support.
Product Specifications 39Appendix CAPPENDIX CProduct SpecificationsComplianceFCC - Class AThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at their own expense.Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.CAUTION STATEMENT: FCC RF Radiation Exposure StatementThis equipment complies with FCC RF radiation exposure limits set forth for fixed indoor use only. This equipment should be installed and operated with a minimum distance of 15.2 inches (38.5 centimeters) for 2.4 GHz and 5GHz operations between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.Radio Frequency Interference RequirementsThis device is restricted to indoor use due to its operation in the 5.15 to 5.25 GHz frequency range. The FCC requires this product to be used indoors to reduce the potential for harmful interference to co-channel Mobile Satellite systems. High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can cause interference with and/or damage this device.
40 Aruba 60/61 Part 0500034Installation Guide July 2004Industry Canada - Class AThis digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of the Department of Communications.Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux appareils numériques de Classe A prescrites dans la norme sur le matériel brouilleur: “Appareils Numériques,” NMB-003 édictée par le ministère des Communications.VCCI - Class ACE - Class AWarning—This is a Class A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures.EU - Class AThis product complies with EN5022 Class A and EN5024 standards.Underwriter LabsThese products have been Listed and tested for fire resistant and low-smoke-producing characteristics, and are suitable for use in environmental air space, such as above suspended ceilings, in accordance with Section 300-22(C) of the National Electrical Code, and Sections 2-128, 12-010(3) and 12-100 of the Canadian Electrical Code, Part 1, CSA C22.1.Peut être utilisé dans des gaines transportant de l’air traité, conformément à la section 300-22(c) du National Electrical Code et aux articles 2-128, 12-010(3) et 12-100 du Code Canadien de l’électricité, Première partie, CSA C22.1.
Product Specifications 41Appendix CCertificationsItem MeasurementElectromagneticCompatibilityFCC Part 15 Class A, FCC Part 15 Class C 15.207/15.247,FCC Part 15 Class E 15.407ICES-003 Class A,RSS 210 (CAN)VCCI Class AEN 61000-3, EN 61000-4-2, EN 61000-4-3, EN 61000-4-4,EN 61000-4-5, EN 61000-4-6, EN 61000-4-8, EN 61000-4-11The CE approval mark on back of the product indicates that it meets European Directives 73/23/EEC and 89/336/EECEN 55022, EN55024 (89/336/EEC),ETS 300 328 (89/336/EEC), ETS 301 489 (89/336/EEC),ETS 301 893AS/NZS 3548 Class A,RFS 29 (NZ)Safety UL Listed (UL60950)UL Listed (Canadian Electrical Code/CSA 22.2 No. 60950)EN60950 / IEC60950National Electrical Code Section 300-22(C)Canadian Electrical Code, Part 1, CSA C22.1 Sections 2-128, 12-010(3), and 12-100
42 Aruba 60/61 Part 0500034Installation Guide July 2004Product FeatureszWireless dual-band transceiverzVaried antenna options: zThe Aruba AP60 has dual Reverse Polarity SMA (RP-SMA) antenna connectors that accept a variety of high-gain detachable antennas (not included).zThe Aruba AP61 has a built-in swivel array with dual, tri-band, omnidirectional antennas for reception diversity.zProtocol-independent networking functionalityzSupports IEEE 802.11a or IEEE 802.11b/g operation as an APzSupports IEEE 802.11a and IEEE 802.11b/g operation as an AMzCompatible with IEEE 802.3af Power Over Ethernet (POE)zSeamless connectivity to wired LANs augment existing networks quickly and easilyzCan be centrally managed, configured, and upgraded through the Aruba WLAN Switch to take advantage of network changes and security improvementsEthernet CompatibilityThe Aruba 60/61 attaches to 10/100 Mbps Ethernet (FE) LAN segments that utilize 10Base-T/100Base-TX (twisted-pair) wiring. The device appears as an Ethernet node and performs a routing function by moving packets between the wired LAN and remote workstations on the wireless infrastructure.Radio CharacteristicsThe Aruba 60/61 can be configured to support IEEE 802.11a or IEEE 802.11b/g operation as an AP, and supports both IEEE 802.11a and IEEE 802.11b/g operation as an AM:z802.11a provides a high data rate and reliable wireless connectivity802.11a operation uses a radio modulation technique known as Orthogonal Frequency Division Multiplexing (OFDM), and a shared collision domain (CSMA/CA). It operates in the 5GHz Unlicensed National Information Infrastructure (UNII) band. Data is trans-mitted over a half-duplex radio channel operating at up to 54 Megabits per second (Mbps).z802.11b provides an alternative to wired LANs that can dramatically cut costs802.11b operation uses the IEEE 802.11 High-Rate Direct Sequence (HRDS) specifica-tion, and a shared collision domain (CSMA/CA). It operates in the 2.4GHz Indus-trial/Scientific/Medical (ISM) band. The ISM band is available worldwide for unlicensed use. Data is transmitted at speeds of up to 11 Mbps.z802.11g provides a high data rate and is backwards compatible with 802.11b.802.11g operation uses ODFM and a shared collision domain (CSMA/CA). It operates in the 2.4GHz Industrial/Scientific/Medical (ISM) band. The ISM band is available world-wide for unlicensed use. Data is transmitted at speeds of up to 54 Mbps.
Product Specifications 43Appendix CPower Over EthernetThe Aruba 60/61 supports the IEEE 802.3af standard for Power Over Ethernet (POE). With this feature, the Aruba 60/61 can accept electrical power from a compatible POE-capable device (such as the Aruba 5000 (with Line Card LC-5000-24FE-2GE-SPOE), Aruba 2400, or Aruba 800) directly over the FE cable. POE eliminates the need to provide separate power outlets in environments that are difficult or undesirable to wire for electricity.The Aruba 60/61 also supports “inline” and “midspan” POE devices for normal operation.Physical DescriptionPackage ContentsThe Aruba 60/61 package includes:zOne Aruba 60/61 Wireless Access PointzAssorted documentationInform your supplier if there are any incorrect, missing or damaged parts. If possible, retain the carton, including the original packing materials. Use them to repack the product in case there is a need to return it.Optional ItemsThe following optional items can also be ordered for the Aruba 60/61:zDetachable antennas (Aruba AP60 only)zAC power adapter (5 VDC, 3 A) and power cordzSerial breakout adapter for direct access to the AP consolezMounting kit (modular cradle for walls and suspended ceilings)Check with your Aruba sales representative for the availability of optional items.The following specifications apply to the Aruba AP60 and Aruba AP61 Wireless Access Points.
44 Aruba 60/61 Part 0500034Installation Guide July 2004Aruba AP-60 Access PointFIGURE 3-5 Part Number: AP-60
Product Specifications 45Appendix CTABLE 3-1 AP-60 802.11 Specifications Description 802.11a 802.11b 802.11gAntenna Dual, diversity supporting Reverse Polarity-SMA (RP-SMA) detachable antenna interfaces suitable for acceptance of single-band or tri-band 802.11a/b/g detachable antennas of various pattern types and gain. For information on third-party antennas, go to the Interoperability section of the Products page at:http://www.arubanetworks.comFrequency Bandz5.250 ~ 5.350Ghz (mid-dle band) 4 channelsz5.725 ~ 5.825Ghz (higher band) 4 channelsz2.4 ~ 2.483Ghz (US, Canada & ETSI)z2.4 ~ 2.497Ghz (Japan)Complete country list available at http://www.arubanetworks.com/products/aps/certificationz2.412 ~ 2.462Ghz (US, Canada)z2.412 ~ 2.472Ghz (ETSI)z2.412 ~ 2.484Ghz (Japan)Complete country list available at http://www.arubanetworks.com/products/aps/certificationRadio Te c h no l og y Orthogonal Frequency Division Multiplexing (OFDM)Direct Sequence Spread Spectrum (DSSS)Orthogonal Frequency Division Multiplexing (OFDM)Modulation Type BPSK, QPSK, 16-QAM, 64-QAMCCK, BPSK, QPSK CCK, BPSK, QPSK, 16-QAM, 64-QAMTransmit Power Configurable by system administrator/professional installerConfigurable by system administrator/professional installerConfigurable by system administratorMedia Access Control CSMA/CA with ACKCSMA/CA with ACKCSMA/CA with ACK
46 Aruba 60/61 Part 0500034Installation Guide July 2004Operating ChannelszUS & Canada: 8 zETSI: 13zJapan: 5Complete country list available at http://www.arubanetworks.com/products/aps/certificationzUS & Canada: 11zETSI: 13zJapan: 13Complete country list available at http://www.arubanetworks.com/products/aps/certificationzUS & Canada: 11zETSI: 13zJapan: 13Complete country list available at http://www.arubanetworks.com/products/aps/certificationData Rates 6, 9, 12, 18, 24, 36, 48, 54 Mbps per channel1, 2, 5.5, 11 Mbps per channel6, 9, 12, 18, 24, 36, 48, 54 Mbps per channelTABLE 3-1 AP-60 802.11 Specifications (Continued)Description 802.11a 802.11b 802.11g
Product Specifications 47Appendix CTABLE 3-2 AP-60 Characteristics DescriptionMaximum Clients 64Multi-mode Radio BandSelectable via softwareManageability: zManagement of all 802.11 parameterszNetwork Wide AP Management via: CLI WEB GUI SNMPv3zAccess Point Profiles, Management by: Geographical Location BSSID Radio TypeEncryption Support (AP and Switch)40bit / 64bit / 128bit / 152bit WEP, TKIP, AESPhysical (HxWxD): z159 x 99 x 31 mm / 6.26 x 3.90 x 1.22 inazWeight 198 grams / 7 ozInterfaces (Electrical):z1 x 10/100 Base-TX auto-sensing Ethernet RJ-45 Interface (Auto-sensing MDI/MDX)zSerial and Power Over Ethernet - 48V DC / 200mA Power Over Ethernet (802.3af compliant) z1 x 5V DC Power InterfaceInterfaces (Mechanical):zStandard Kensington MicroSaver Security Cable Interface (cable not supplied)zWall and ceiling mount kit (optional - part number AP-60-MNT) interface
48 Aruba 60/61 Part 0500034Installation Guide July 2004Visual Indicators (LEDs)Ready -- Power Ethernet link status / Activity WLAN ActivityPower zOptional AC Power Adapter Input—100-240 AC, 50-60 HzzAccess Point Input—5 VDC, 3 A (AC adapter), or48 VDC, 200 mA (POE)Power Requirements z5V DC / 2A supplied externally via optional AC adapter kitz48V DC / 200mA Power Over Ethernet (802.3af compliant) zAuto-sensing externally supplied AC power or Power Over EthernetOutput Power 100 mW maximum (or lower as configured on the Aruba WLAN Switch to comply with local regulatory requirements)Environmental:Humidity Humidity 5% to 95% (non-condensing)Standards CompliancezEthernet IEEE 802.3 / IEEE 802.3uzPower Over Ethernet IEEE 802.3afzWireless IEEE 802.11a/b/gTABLE 3-2 AP-60 Characteristics (Continued)Description
Product Specifications 49Appendix CElectromagnetic CompliancezFCC Part 15 Class A, FCC Part 15 Class C 15.207/15.247zFCC Part 15 Class E 15.407zICES-003 Class A,zRSS 210 (CAN)zVCCI Class AzEN 61000-3, EN 61000-4-2, EN 61000-4-3, EN 61000-4-4,zEN 61000-4-5, EN 61000-4-6, EN 61000-4-8, EN 61000-4-11zEN 55022, EN55024 (89/336/EEC),zETS 300 328 (89/336/EEC), ETS 301 489 (89/336/EEC)zETS 301 893zAS/NZS 3548 Class ASafety Compliance zCSA/NTRL (CSA 22.2 No. 950 & UL 1950)zEN60950 (TÜV/GS), IEC60950 (CB)a. Measurements indicate only the Access Point chassis. Size and weight do not include othermaterials (such as detachable antennas, mounting kits, and cables) which may varyTABLE 3-2 AP-60 Characteristics (Continued)Description
50 Aruba 60/61 Part 0500034Installation Guide July 2004Aruba AP-61 Access PointFIGURE 3-6 Part Number: AP-61
Product Specifications 51Appendix CTABLE 3-3 AP-61 802.11 Specifications Description 802.11a 802.11b 802.11gAntenna Integral, diversity supporting dual, tri-band 802.11a/b/g omni-directional high-gain antennas with 90 degrees rotational movementIntegral antenna gain: 2.4 Ghz / 2.8dBi 5.150-5.350 Ghz / 3.9dBi 5.6 Ghz / 4 dBiFrequency Band z5.150 ~ 5.250Ghz (lower band) 4 channelsz5.250 ~ 5.350Ghz (middle band) 4 channelsz5.725 ~ 5.825Ghz (higher band) 4 channelsz2.4 ~ 2.483Ghz (US, Canada & ETSI)z2.4 ~ 2.497Ghz (Japan)Complete country list available at http://www.arubanetworks.com/products/aps/certificationz2.412 ~ 2.462Ghz (US, Canada)z2.412 ~ 2.472Ghz (ETSI)z2.412 ~ 2.484Ghz (Japan)Complete country list available at http://www.arubanetworks.com/products/aps/certificationRadio Tech n o l o g y Orthogonal Frequency Division Multiplexing (OFDM)Direct Sequence Spread Spectrum (DSSS)Orthogonal Frequency Division Multiplexing (OFDM)Modulation Type BPSK, QPSK, 16-QAM, 64-QAMCCK, BPSK, QPSK CCK, BPSK, QPSK, 16-QAM, 64-QAMTransmit Power Configurable by system administrator/professional installerConfigurable by system administrator/professional installerConfigurable by system administratorMedia Access Control CSMA/CA with ACKCSMA/CA with ACKCSMA/CA with ACK
52 Aruba 60/61 Part 0500034Installation Guide July 2004Operating ChannelszUS, Canada & ETSI: 12zJapan: 5Complete country list available at http://www.arubanetworks.com/products/aps/certificationzUS & Canada: 11zETSI: 13zJapan: 13Complete country list available at http://www.arubanetworks.com/products/aps/certificationzUS & Canada: 11zETSI: 13zJapan: 13Complete country list available at http://www.arubanetworks.com/products/aps/certificationData Rates 6, 9, 12, 18, 24, 36, 48, 54 Mbps per channel1, 2, 5.5, 11 Mbps per channel6, 9, 12, 18, 24, 36, 48, 54 Mbps per channelTABLE 3-3 AP-61 802.11 Specifications (Continued)Description 802.11a 802.11b 802.11g
Product Specifications 53Appendix CTABLE 3-4 AP-61 Characteristics DescriptionMaximum Clients 64Multi-mode Radio BandSelectable via softwareManageability: zManagement of all 802.11 parameterszNetwork Wide AP Management via: CLI WEB GUI SNMPv3zAccess Point Profiles, Management by: Geographical Location BSSID Radio TypeEncryption Support (AP and Switch)40bit / 64bit / 128bit / 152bit WEP, TKIP, AESPhysical (HxWxD):zAntenna up, stand closed—216 x 99 x 31 mm / 8.50 x 3.90 x 1.22 ina zAntenna up, stand open—209 x 99 x 74 mm / 8.23 x 3.90 x 2.91 inzAntenna 90o, stand closed— 159 x 99 x 71 mm / 6.26 x 3.90 x 2.80 inzWeight 255 grams / 9 oz
54 Aruba 60/61 Part 0500034Installation Guide July 2004Interfaces (Electrical):z1 x 10/100 Base-TX auto-sensing Ethernet RJ-45 Interface (Auto-sensing MDI/MDX)zSerial and Power Over Ethernet - 48V DC / 200mA Power Over Ethernet (802.3af compliant) z1 x 5V DC Power InterfaceInterfaces (Mechanical):Standard Kensington MicroSaver Security Cable Interface (cable not supplied)Wall and ceiling mount kit (optional - part number AP-60-MNT) interfaceVisual Indicators (LEDs)Ready -- Power Ethernet link status / Activity WLAN ActivityPower zOptional AC Power Adapter Input—100-240 AC, 50-60 HzzAccess Point Input—5 VDC, 3 A (AC adapter), or48 VDC, 200 mA (POE)Power Requirementsz5V DC / 2A supplied externally via optional AC adapter kitz48V DC / 200mA Power Over Ethernet (802.3af compli-ant) zAuto-sensing externally supplied AC power or Power Over EthernetOutput Power 100 mW maximum (or lower as configured on the Aruba WLAN Switch to comply with local regulatory requirements)Environmental:Temperature zOperating: 0 to 50 ºC (32 to 122 ºF)zStorage: 0 to 70 ºC (32 to 158 ºF)TABLE 3-4 AP-61 Characteristics (Continued)Description
Product Specifications 55Appendix CEnvironmental:Humidity Humidity 5% to 95% (non-condensing)Standards CompliancezEthernet IEEE 802.3 / IEEE 802.3uzPower Over Ethernet IEEE 802.3afzWireless IEEE 802.11a/b/gElectromagnetic CompliancezFCC Part 15 Class A, FCC Part 15 Class C 15.207/15.247zFCC Part 15 Class E 15.407zICES-003 Class A,zRSS 210 (CAN)zVCCI Class AzEN 61000-3, EN 61000-4-2, EN 61000-4-3, EN 61000-4-4,zEN 61000-4-5, EN 61000-4-6, EN 61000-4-8, EN 61000-4-11zEN 55022, EN55024 (89/336/EEC),zETS 300 328 (89/336/EEC), ETS 301 489 (89/336/EEC)zETS 301 893zAS/NZS 3548 Class ASafety CompliancezCSA/NTRL (CSA 22.2 No. 950 & UL 1950)zEN60950 (TÜV/GS), IEC60950 (CB)a. Measurements indicate only the Access Point chassis. Size and weight do not in-clude other materials (such as detachable antennas, mounting kits, and cables)which may varyTABLE 3-4 AP-61 Characteristics (Continued)Description
56 Aruba 60/61 Part 0500034Installation Guide July 2004Related DocumentsThe following items are part of the complete documentation for the Aruba system:zAruba AP Starter’s GuidezAruba AP Installation Guide (this document)zAruba WLAN Switch Installation GuidezAruba RF Director Starter’s GuidezAruba AirOS User’s GuidezAruba AirOS Command ReferenceFor the current versions of these manuals, or to obtain the latest product release notes, visit the support section of our Web site (see page 58).
Product Specifications 57Appendix CText ConventionsThe following conventions are used throughout this manual to emphasize important concepts:TABLE 3-5 Text ConventionsType Style DescriptionItalics This style is used to emphasize important terms and to mark the titles of books.System items This fixed-width font depicts the following:zSample screen outputzSystem promptszFilenames, software devices, and certain commands when men-tioned in the text.Commands In the command examples, this bold font depicts text that the user must type exactly as shown.<Arguments> In the command examples, italicized text within angle brackets represents items that the user should replace with information appropriate to their specific situation. For example:# send <text message>In this example, the user would type “send” at the system prompt exactly as shown, followed by the text of the message they wish to send. Do not type the angle brackets.[ Optional ] In the command examples, items enclosed in brackets are optional. Do not type the brackets.{ Item A | Item B } In the command examples, items within curled braces and separated by a vertical bar represent the available choices. Enter only one choice. Do not type the braces or bars.
58 Aruba 60/61 Part 0500034Installation Guide July 2004Contacting Aruba Wireless NetworksWeb SiteE-mailTelephone NumberszMain Site http://www.arubanetworks.comzSupport http://www.arubanetworks.com/supportzSales sales@arubanetworks.comzSupport support@arubanetworks.comzMain 408-227-4500zFax 408-227-4550zSales 408-754-1201zSupport In the U.S.: 800-WI-FI-LAN (800-943-4526)International: 408-754-1200
Notes 59Notes
180 Great Oaks Blvd. Ste BSan Jose, California 95119www.arubanetworks.comTel 408.227.4500Fax408.227.4550

Navigation menu