Hexing Electrical MJP900-A1 HexNet RF Module User Manual
Hexing Electrical Co.,Ltd HexNet RF Module Users Manual
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3052124 |
| Application ID | QWdovQwYbtgVV2PdOqaJKQ== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 39.86kB (498214 bits) |
| Date Submitted | 2016-07-05 00:00:00 |
| Date Available | 2016-07-05 00:00:00 |
| Creation Date | 2017-12-09 15:39:29 |
| Producing Software | GPL Ghostscript 9.18 |
| Document Lastmod | 2017-12-09 15:39:29 |
| Document Title | Microsoft Word - HexNet RF Module（MJP900）User manual V01.docx |
| Document Creator | PScript5.dll Version 5.2.2 |
| Document Author: | HEW076 |
HexNet RF Module MJP900 User Manual Version Maker Date V0.0.1 WangGang 2016.04.20 Hexing Electrical Co.,Ltd. 〉〉〉HexNet RF Module 1.Product Introduction The HexNet RF module is a highly integrated half-duplex micropower wireless data transmission module.The HexNet RF module embedded high-performance RF chip.User programming has very good flexibility.This module provides multiple channels of choice, can modify transmission power, data rate and other parameters.HexNet module operating frequency include 915MHZ. The real figure as shown in the figure below. 2.RF Module Chip Block Diagram 3.RF Module Pin Definition 10 11 12 13 14 RF GND MISO MOSI NSS SCK RST DIO0 DIO1 NC DIO3 NC GND VCC RF Antenna GND SPI Data Out SPI Data In SPI Selected Pin SPI Clock RESET Pin RXDone、TXDone、CADDone FHSS NC CADDetected，PLL_Lock NC GND Power 4. 4-wire Serial Configuration and Data Interface HexNet is configured via a simple 4-wire SPI-compatible interface (MOSI, MISO, SCLK, and NSS) where HexNet is the slave. This interface is also used to read and write buffered data. Figure 1 Configuration Registers Write and Read Operations MOSI is generated by the master on the falling edge of SCK and is sampled by the slave (i.e. this SPI interface) on the rising edge of SCK. MISO is generated by the slave on the falling edge of SCK. A transfer is always started by the NSS pin going low. MISO is high impedance when NSS is high. The first byte is the address byte. It is comprises: ¾ A wnr bit, which is 1 for write access and 0 for read access. ¾ Then 7 bits of address, MSB first. The second byte is a data byte, either sent on MOSI by the master in case of a write access or received by the master on MISO in case of read access. The data byte is transmitted MSB first. Proceeding bytes may be sent on MOSI (for write access) or received on MISO (for read access) without a rising NSS edge and re-sending the address. In FIFO mode, if the address was the FIFO address then the bytes will be written / read at the FIFO address. In Burst mode, if the address was not the FIFO address, then it is automatically incremented for each new byte received. The frame ends when NSS goes high. The next frame must start with an address byte. The SINGLE access mode is therefore a special case of FIFO / BURST mode with only 1 data byte transferred. During the write access, the byte transferred from the slave to the master on the MISO line is the value of the written register before the write operation. 5. User operation Insert the HexNet module on user’s printed circuit boards，use MCU SPI SPI communication with the module.Control the RF register and FIFO to wireless data transceiver functions. complete Note： 1 Thank you for using products of Hexing Electrical Co., Ltd. Please read this warning before using our products. If you have already started to use is that you have read and accept our all this. 2 All the final explanation and modification rights for all materials were reserved by Hexing Electrical Co., Ltd. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. To satisfy FCC RF Exposure requirements for this transmission devices, a separation distance of 20cm or more should be maintained between the antenna of this device and persons during operation. To ensure compliance, operation at closer than this distance is not recommended. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number： (A) If using a permanently affixed label, the modular transmitter must be labeled with its own FCC identification number, and, if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID:2AIUZ-MJP900-A1” Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V4.4 (128-bit) User Access : Print, Extract, Print high-res Author : HEW076 Create Date : 2016:06:22 16:03:01+08:00 Modify Date : 2016:07:05 19:13:12-07:00 Has XFA : No XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Producer : Acrobat Distiller 7.0.5 (Windows) Creator Tool : PScript5.dll Version 5.2.2 Metadata Date : 2016:07:05 19:13:12-07:00 Format : application/pdf Title : Microsoft Word - HexNet RF Module（MJP900）User manual V01.docx Creator : HEW076 Document ID : uuid:22c03039-96e3-4076-b8d6-7edda8a85196 Instance ID : uuid:a9b5b900-5382-4ad0-aedc-668849d34614 Page Count : 6EXIF Metadata provided by EXIF.tools