| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3688900 |
| Application ID | kC8JNd4Ij3KHWRtB8mHbjQ== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 478.87kB (5985908 bits) |
| Date Submitted | 2017-12-22 00:00:00 |
| Date Available | 2018-02-05 00:00:00 |
| Creation Date | 2017-12-04 14:41:07 |
| Producing Software | Adobe PDF Library 10.0.1 |
| Document Lastmod | 2017-12-08 09:33:56 |
| Document Title | User Manual |
| Document Creator | Adobe InDesign CS6 (Windows) |
Thank you for purchas ng our oroduct, an rdea‘ radio system for begrnners or expenenceo users 3er
Read thrs manua‘ carequy before operatron rn order to ensure your safety and the safety 0’ others or the safe
operauon oryour syszern
H you encounter any probrem pers sts, contact your rocar dearer or v‘rsr’t our service and supoort website for herp:
www.hobbyking.com
1. Safety
1.1 Safety Symbols
Pay close attenuon to the lollowtng symbols and thetr meantngs Fatlure to follow these warnmgs could cause damage,
tnyury or death
A Danger - Not following these instructions may lead to serious injuries or death.
A Warning - Not following these instructions may lead to major injuries.
A Attention - Not following these instructions may lead to minor injuries.
1.2 Safety Guide
8 Prohibited 0 Mandatory
- Do not use the product at night or in bad weather like rain or thunderstorm. It can
cause erratic operation or loss of control.
- Do not use the product when visibility is limited.
~ Do not use the product on rain or snow days. Any exposure to moisture (water or
snow) may cause erratic operation or loss of control.
- Interference may cause loss of control. To ensure the safety of you and others, do
not operate in the following places:
- Near any site wnere other radto control acttvtty may occur
' Near power ltnes or commun canon broadcasttrg antennas
® - Near people or roads
- On any oody of water when passenger boats are present
- Do not use this product when you are tired. uncomfortable. or under the influence
of alcohol or drugs. Doing so may cause serious injury to yourself or others.
- The 2.4GHz radio band is limited to line of sight. Always keep your model in sight as
a large object can block the RF signal and lead to loss of control.
~ Never grip the transmitter antenna during operation. It significantly degrades signal
quality and strength and may cause loss of control.
- Do not touch any part of the model that may generate heat during operation, or
immediately after use. The engine. motor or speed control. may be very hot and can
cause serious burns.
- Misuse of this product may lead to serious injury or death. To ensure the safety of
you and your equipment, read this manual and follow the instructions.
- Make sure the product is properly installed in your model. Failure to do so may
result in serious injury.
- Make sure to disconnect the receiver battery before turning off the transmitter.
Failure to do so may lead to unintended operation and cause an accident.
- Ensure that all motors operate in the correct direction. If not, adjust the direction
first.
~ Make sure the model flies within a certain distance. Otherwise, it would cause loss of
control.
2. Transmitter Overview
56—— {r , _ss
57
54
53
SS
51
52
Lanyard hook
‘—— EIevaior/Ai'leron
Thoma/Rudder ‘
Mm _ '—— Trim
Trim — “ Trim
Binding key —
Whee‘
Cancel key —
- LCD
Antenna
Hand‘e
— Trainer port
Grip
— Battery compartment
3. Binding
The transrn tter and receiver have been prefbound before deiivery.
ityou are using another transmitter or receiver, toi ow the steps beiow to bind the transmitter and receiver
I'm A
i Connected the bind cabie to the bind port of the receiver
2 Connected the power to any other port, The ind cator wiii start to flash in orange, indicating that the receiver iS in
bind mode
3. Press and hoid the binding key and turn on the transmitter i’ of Tum on ' t tta ’ tr oruss and
to (”iti'ir tee Tia ri menu to we [Li fl‘i'iCD‘ soup than rhoost' too 0 rd Time bier: Ft] "i“
- T'ie system Wiii cispiayed ‘RX bind'ng ‘, Aiter successiuiiy binding the transmitter wiii automaticaiiy exit th's
menu, the receivers LED wiii stop flushing, remaining soiid, indicating that binding has been successfui.
4. Main Screen
The main screen dispiays usetui ir‘torrnatin about your modei, inciuding sensors and function status etc.
Hind-21 —E'll TH 5-D”
\ i::i-.1 [H1 II
Timer's status \ Che E Hi % Chz
\ Eh4 E H CM
Trim DFF
==|
/ Trim
\ _ RF protccci
Modei name
— Battery status
Modei type
Trim
Trim
5. Airplane
ihis section eonta ns the detauit menu function settings.
5.1 Servo setup
5.1.1 Reverse
The function 5 used to correct a servo or motor‘s direction n reiation to the systems controis.
For exampie, ita servo is mounted upside down in orderto fit inside a modei
Setup.
T Press the wheei in oroer to charge between charneis. _Hever.se
2, Move the wheei iett or right to change between “Nor“ t\n rm; and
“Rev“ iiie‘reriei Ch
1 2 3 4 5 B
- Seiect the channei you want to reset, then press and hoid the cancei key “OP
to reset to detauit vaiue qeu
3. Press and hoid the wheei to save and ed, or press the cancei key to exit
Without saving
5.1.2 End points
Endpoints are the iimits of the channeis‘ range of movement There are two endpoints, the iow endpoint and the high
end pOii'ii.
Setup“
T Press the wheei to chahge between chahneis
2. Move the channei using the stick in order to choose a high or iow side
3. Move the wheei iett or right to change the endeints vaiue.
- Seiect a channei and a high side or iow side, then press ahd hoid the
cancei