Hideki Electronics TS33-C Outdoor Temperature & Humidity Transmitter User Manual

Download:
Mirror Download [FCC.gov]
Document ID	528752
Application ID	I993g06CdaeMI68vYi7LJA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	11.53kB (144064 bits)
Date Submitted	2005-04-01 00:00:00
Date Available	2005-04-01 00:00:00
Creation Date	2005-02-17 10:56:47
Document Lastmod	2005-02-17 10:57:09
Document Title	User Manual
Document Creator	HP 9100C Digital Sender
Document Author:	BEN HO

(MAMA/3L FOR TSE'S'C>
THERMO- HYGRO REMOTE SENSOR
User Manual
INTRODUCTION
Congratulations on your purchase 0 this thermo—hygro remote sensor.
MAIN FEATURES: REMOTE UNIT
A LED INDICATOR
Flashes once when the remote unit transmits a reading
Flashes twice when low battery is detected on sensor unit
B BATTERY COMPARTMENT
Accommodates two AA-size batteries
c RESET BUTTON
Press to reset all setting if you have selected different channel,
D CHANNEL SELECTOR
Select the channel before you install batteries.
E WALL-MOUNT RECESSED HOLE
Supports the remote until in wall—mounting
F °CI °F BUTI'ON
Selects between Centigrade (°C) and Fahrenheit (“F)
G LCD DISPLAY
Outdoor temperature and humidity are displayed.
BEFORE YOU BEGIN
For best operation,
1. Insert batteries for remote units before doing so for the main unit.
2. Place the main unit as close as possible next to the remote unit.
3. Position the remote unit and main unit within effective transmission range, which, in
usual circumstances, is 20 to 30 meters.
Note that the effective range is vastly affected by the building materials and where the
main and remote units are positioned Try various set-ups for best result
Though the remote units are weather proof, they should be placed away from direct
sunlight, rain or snow.
BATTERY INSTALLATION: REMOTE UNIT
1. Remove the screws on the battery compartment.
2. Select the channel
3. Install 2 batteries (UM»3 or “AA” size 1.5V) strictly according to the polarities shown.
4. Replace the battery compartment door and secure its screws.
TRANSMISSION COLLISION
Signals from other household devices, such as door bells, home security systems and
entry controls, may interfere with those of this product and cause temporarily reception
failure. This is normal and does not affect the general performance of the product The
transmission and reception of temperature readings will resume once the interference
recedes Different channel may be reducing the interference
PRECAUTIONS
This product is engineered to give you years of satisfactory service ifyou handle it
carefully. Here are a few precautions:
I , Do not immerse the unit in wateri
2, Do not clean the unit with abrasive or corrosive materials.
They may scratch the plastic parts and corrode the electronic circuit.
3. Do not subject the unit to excessive force, shock, dust, temperature or humidity, which
may result in malfunction, shorter electronic life span, damaged battery and distorted
parts.
4. Do not tamper with the unit's internal components.
Doing so will invalidate the warranty on the unit and may cause unnecessary damage.
The unit contains no user-serviceable parts.
5. Only use fresh batteries as specified in the user's manual.
Do not mix new and old batteries as the old ones may leak.
6. Always read the user's manual thoroughly before operating the unit.
SPECIFICATIONS
Temperature
Proposed operating range: -20.0°C to + 70.0°C/ - 4,0 “F to 158.0 °F
Temperature resolution: 0.1°C/ 02°F
Humidity
Proposed operating range: 25% to 90%
Resolution: 1%
RF Transmission Frequency: 433 MHz
Maximum number ofRemote sensors: 3
RF Transmission Range: Maximum 100 feet
Temperature sampling cycle: approximately 45 seconds
Power
Remote Sensor: 2 x UM-3/ AA (1,5V) alkaline batteries are suggested (not included)
Dimensions
Remote sensor: 2,37”(L) x 4"(H) x 1”(D)
FCC STATEMENT
This device complies with Part 15 ofthe FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) This device
must accept any interference received, including interference that may cause undesired
operation,
Warning: Changes or modification to this unit not expressly approved by the party
responsible for compliance could void the user‘s authority to operate the equipment.
NOTE: This equipment had been tested and found to comply with the limits for a Class B
Digital device, pursuant to Part 15 ofthe FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment, installed and used in accordance with the instructions, may cause harmful
interference to radio communications
There is no guarantee that interference will not occur in a particular installation, If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct
turning the interference by one or more ofthe following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
4, Consult the dealer or an experienced radio / TV technician for help.
w»—
STANDARD WARRANTY INFORMATION
This product is warranted from the manufacturing defects for one year from date of retail
purchase. It does not cover damages or wear resulting from accident, misuse, abuse,
commercial use, or unauthorized adjustment and/ or repair.
Note that online product registration is required to ensure valid Warranty protection.
To register your product, go to our Company website at: wwwhidekielectronicscom.
Click Online Product Registration under the Customer Service menu.
Should you require assistance with this product and its operation, please contact our
Customer Service Hotline l(866) 443 3543
Please direct all returns to the place ofthe original purchaser Should this not be possible,
contact Customer Service Hotline for assistance and to obtain a Return Merchandise
Authorization (RMA). Returns without a return authorization will be refused, Please
retain your original receipt as you may be asked to provide a copy for proof of purchase.
Hideki Electronics, Inc. reserves the right to repair or replace the product at our option.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Modify Date                     : 2005:02:17 10:57:09+08:00
Create Date                     : 2005:02:17 10:56:47+08:00
Title                           : 
Subject                         : 
Author                          : BEN HO
Creator                         : HP 9100C Digital Sender
Producer                        : 
Page Count                      : 4
Mod Date                        : 2005:02:17 10:57:09+08:00
Creation Date                   : 2005:02:17 10:56:47+08:00
Metadata Date                   : 2005:02:17 10:57:09+08:00

EXIF Metadata provided by EXIF.tools