Hinge Health HINGE2 Hinge Sensor User Manual
Hinge Health, Inc Hinge Sensor
User Manual
1
GETTING STARTED
Digitl Cre Progrm
Knee Pthwy
WAIT A SECOND
Stretching and strengthening exercises are recommended
by the American Orthopaedic Association.
While it’s good to go through a full range of motion, only
go as far you feel comfortable. If the exercises cause you
significant pain, please stop and consult your coach.
THE HINGE HEALTH KIT
In your Hinge Health kit you will find:
• 1 Tablet with the Hinge Health app installed
• 1 Tablet stand
• 1 Tablet charger
• 2 Knee motion sensors with straps
• 1 Y-Cable sensor charger
• 3 Resistance bands
CONNECTING TO WI-FI
The Hinge Health app needs to be connected to the
Internet to work correctly. So, before you get started
take a minute to set the tablet up on your home Wi-Fi
network.
1. Tap on the Settings icon on the tablet home
screen to take you into the tablet settings.
2. Tap on Wireless to access the Wi-Fi settings.
3. Tap on Wi-Fi to take you to a list of available
networks.
4. Find your home network from the available list
and select it. Enter your Wi-Fi password and tap
Connect. You should now be connected to the
Internet and have access to the Hinge Health app.
Flashing red means the battery is dead.
To charge the sensors connect the Y-Cable
sensor charger to the motion sensors and plug
the main power plug into a wall socket.
Flashing orange means the battery is charging.
Once connected to an outlet, the sensors
should start to flash orange.
White means the battery is fully charged.
This usually takes around two hours.
Green means the sensors are on and the
batteries have charge.
YOUR HINGE HEALTH SENSORS
The wearable motion sensors included in your kit will
help guide you through the exercise therapy program in
the Hinge Health app. You will find instructions on using
the sensors in the app.
The light on each sensor has four dierent states:
HELP
Should you need anything, don’t hesitate to:
Message your coach in the app
Call: (855) 902-2777
E-mail: help@hingehealth.com
WEARABLE SENSOR REGULATORY INFORMATION
Motion sensor model number, FCC ID (U.S) and IC (Canada) can be
accessed within the Hinge Health mobile application by navigation to
Settings > Legal > Regulatory.
FCC
This equipment has been tested and found to comply with the limits
for a class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receive
• Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician
for help
This equipment has been verified to comply with the limits for
a class B computing device, pursuant to FCC Rules. In order
to maintain compliance with FCC regulations, shielded cables
must be used with this equipment. Operation with non-approved
equipment or unshielded cables is likely to result in interference
to radio and TV reception. The user is cautioned that changes
and modifications made to the equipment without the approval
of manufacturer could void the user’s authority to operate this
equipment.
ISED
This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes: (1) l’appareil ne doit
pas produire de brouillage, et (2) l’utilisateur de l’appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d’en compromettre le fonctionnement.
