Hirschmann Automation and Control EWLAN1 802.11abgn Module User Manual U99EWLAN1 integration manual v2

Hirschmann Automation and Control GmbH 802.11abgn Module U99EWLAN1 integration manual v2

Contents

integration manual

Integration Information
FCC ID: U99EWLAN1
IC: 4019A-EWLAN1
Page 1/8
EWLAN1 integration manual
The EWLAN1 Module is a 3x3 3-stream IEEE 802.11 a/b/g/n wireless LAN
module in PCI express mini card form factor, designed to deliver high-reliable
radio performance for a variety of bandwidth-intensive wireless applications.
Outer Appearance
Top view with Samtec connector (PCI express):
Rear view with antenna connectors:
Dimensions:
34 mm (w) x 54mm (l) x 10 mm (h)
Integration Information
FCC ID: U99EWLAN1
IC: 4019A-EWLAN1
Page 2/8
General requirements:
This module is designed exclusively for usage in Hirschmann (Belden) host
equipment. A regulated power supply via the dedicated interface to the WLAN
module is required.
This RF module is approved only for use in products operating as fixed or mobile
transmitting device where the antennas are at least 50 cm away from any
persons during normal operating conditions.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
The integrator is still responsible for the FCC compliance requirement of the end
product, which integrates this module.
Appropriate measurements (e.g. 15 B compliance) and if applicable additional
equipment authorizations (e.g. Verification , Doc) of the host device to be
addressed by the integrator/manufacturer.
Hardware Integration
EWLAN1 supports the PCI express standard from the electrical power supply
and signaling point of view. To enhance connection reliability in harsh
environments between EWLAN1 and the host equipment, Samtec interface
connectors have been selected.
Integration Information
FCC ID: U99EWLAN1
IC: 4019A-EWLAN1
Page 3/8
EWLAN1 is equipped with Samtec connector QRM8
The host equipment has to be equipped with Samtec connector
QRF8-026-05.0-L-D-A-GP
Pin assignment of QRF8-026-05.0-L-D-A-GP
Integration Information
FCC ID: U99EWLAN1
IC: 4019A-EWLAN1
Page 4/8
Data Interface Pin definition
Pin Signal Comment Pin Signal Comment
1 GND ground 2 GND ground
3 Res open 4 Res open
5 GND ground 6 Res open
7 Res open 8 Res open
9 GND ground 10 Res open
11 Res open 12 GPIO10 GPIO-Interface
13 Res open 14 GPIO7 GPIO-Interface
15 GND ground 16 GND ground
17 Res open 18 PERST_L /Reset
19 GND ground 20 GND ground
21 VCC3.3 3.3V ±5% 22 VCC3.3 3.3V ±5%
23 VCC3.3 3.3V ±5% 24 VCC3.3 3.3V ±5%
25 GND ground 26 GND ground
27 Res open 28 PETp0 PCIe Tx+
29 GND ground 30 PETn0 PCIe Tx-
31 Res open 32 GND ground
33 Res open 34 PERp0 PCIe Rx+
35 GND ground 36 PERn0 PCIe Rx-
37 GND ground 38 GND ground
Integration Information
FCC ID: U99EWLAN1
IC: 4019A-EWLAN1
Page 5/8
39 VCC1.2 1.2V ±5% 40 REFCLK+ PCIe Ref Clock+
41 VCC1.2 1.2V ±5% 42 REFCLK- PCIe Ref Clock-
43 GND ground 44 GND ground
45 GND ground 46 GND ground
47 Res open 48 CLKreq_L /Clock request
49 Res open 50 WAKE_L /PCIe awake
51 GND ground 52 GND ground
Integration Information
FCC ID: U99EWLAN1
IC: 4019A-EWLAN1
Page 6/8
Power Requirements
ELWAN1 has to be powered as follows:
3.3VDC at VCC3.3
1.28VDC at VCC1.2
Antenna Connectors
The antenna connectors of EWLAN1 are micro miniature coaxial types (MMCX).
Antennas (USA/Canada)
The usage of the antennas for products shipped to North America (USA and
Canada) is restricted to the models and bands below:
Antennas operating with this device
model (Hirschmann model names)
Permitted band of operation
2.4 GHz
Band
5.15-5.25 GHz
Band
5.725-5.825 GHz
Band
BAT-ANT-RSMA-2AGN-R Yes Yes Yes
BAT-ANT-N-3AGN-IP67 Yes Yes Yes
BAT-ANT-N-MiMoDB-5N-IP65 Yes Yes Yes
BAT-ANT-N-MiMo5-9N-IP65 No Yes Yes
BAT-ANT-N-8G-DS-IP65 Yes No No
SW Integration
EWLAN1 is designed for usage with Hirschmann host equipment (motherboards)
running the HiLCOS operating system 8.60.x or higher versions.
Only HiLCOS versions with fixed (non-adjustable) radio parameters for
USA/Canada are allowed for products intended for the North American market.
Integration Information
FCC ID: U99EWLAN1
IC: 4019A-EWLAN1
Page 7/8
Regulatory Requirements (FCC/IC)
If intended for the North American market the following regulatory requirements
apply:
1) ELWAN1 needs to be labeled with the FCC ID and Canada number:
FCC ID: U99EWLAN1
IC: 4019A-EWLAN1
2) The host product need to be labeled as below:
3) The user guide of the host equipment shall contain the following
information:
FCC note:
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions:
This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause
undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
This device complies with Part 15 of the FCC Rules and Industry
Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
CAN ICES-3 (B)/NMB-3(B)
Contains Transmitter Module
FCC ID: U99EWLAN1
IC: 4019A-EWLAN1
Integration Information
FCC ID: U99EWLAN1
IC: 4019A-EWLAN1
Page 8/8
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
Note: The following paragraph is valid for devices labeled with
FCC ID: U99EWLAN1 and IC: 4019A-EWLAN1:
Important note: This equipment complies with FCC and IC RSS-102 radiation exposure
limits set forth for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 50 cm (19.7 in, applied to a 9 dBi antenna) between the
radiator and your body. The antenna used for this transmitter must not be co-located with
any other transmitters within a host device, except in accordance with FCC multi-
transmitter product procedures.
This transmitter is restricted to indoor use only within the 5.15-5.25 GHz band to reduce
potential for harmful interference to co-channel mobile satellite systems.
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique
de la classe B est conforme à la norme NMB-003 du Canada. To reduce potential radio
interference to other users, the antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (EIRP) is not more than that permitted for
successful communication.
This device has been designed to operate with the antennas listed below in point-to-
multipoint systems, and having a maximum gain of 9 dBi:
Antennas operating with this device model: Permitted band of operation
2.4 GHz Band 5.15-5.25 GHz Band 5.725-5.825 GHz Band
BAT-ANT-RSMA-2AGN-R
(
1
)
Yes
Yes
Yes
BAT-ANT-N-3AGN-IP67 Yes Yes Yes
BAT-ANT-N-MiMoDB-5N-IP65 Yes Yes Yes
BAT-ANT-N-MiMo5-9N-IP65 No Yes Yes
BAT-ANT-N-8G-DS-IP65 Yes No No
Antennas not included in this list are prohibited for use with this device. The required
antenna impedance is 50 ohms.
Note (1): When using three antennas of the type BAT-ANT-RSMA-2AGN-R, each
antenna has to be aligned into a separate spatial direction (x-y-z), where one antenna is
perpendicular to the device and the other two are at right angles to each other.

Navigation menu