Hisense Electric BRCB0007 BT remote User Manual W9HBRCB0007 Rev3
Hisense Electric Co., Ltd. BT remote W9HBRCB0007 Rev3
W9HBRCB0007_User Manual_Rev3
Remote Control
FCC Notice
•This device complies with Part 15 of the FCC Rules. Operation is subject to the follow
two conditions: (1)this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause
undesired operation.
•The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the
user’s authority to operate the equipment.
Industry Canada Notice
•This device complies with industry Canada licenseexempt RSS standards(s).
Operation is subject to the following two conditions:(1)this device may not cause
interference, and (2)this device must accept any interference, including interference
that may cause undesired operation of the device.
Remote Control
FCC Notice
•This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy,
and if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
•However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment OFF and ON, the user
is encouraged to try to correct the interference by one or more of the following
measures: 1)Reorient or relocate the receiving antenna 2)Increase the separation
between the equipment and receiver 3)Connect the equipment into an outlet on a
circuit different from that to which the receiver is connected 4)Consult the dealer or
an experienced radio/TV technician for help.
Remote Control
Remote Control
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject
to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
1) l’appareil ne doit pas produire de brouillage;
2) l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
Remote Control
Remote control range information
•The remote control can work at a distance of up to 26 feet in front of the TV set.( This
distance is used by infrared means in an unpaired state.)
•It can work at a 30 degree horizontal or vertical angle.( This angle is used by infrared means
in an unpaired state.)
Begin using your remote
•Slide the back cover to open the battery compartment of the remote control.
•Insert two AAA size batteries. Make sure to match the (+) and (-) ends of the batteries with
the (+) and (-) ends indicated in the battery compartment.
•Replace the battery compartment cover.
NOTES
•Discard batteries in a designated disposal area. Do not throw them into a fire.
•Remove old batteries immediately to prevent them from leaking into the battery
compartment.
Remote Control
Remote Control
•If you do not intend to use the remote control for a long time, remove the batteries. Battery
chemicals can cause a rash. If the batteries leak, clean the battery compartment with a cloth.
If chemicals touch your skin then wash it immediately.
•Do not mix old and new batteries.
•Do not mix alkaline, standard (carbon-zinc) or rechargeable (NiCd, NiMH, etc.) batteries.
•Do not continue using the remote if it gets warm or hot.
•Call our Support Center immediately on the support website.
Pairing the Remote Control
•Pair the remote to the TV after you power it on. Keep the remote control within 20 feet from
the TV. Press down the [MENU] button at least 3 seconds to start pairing.
•If the remote paired successfully then a confirmation will display on the screen. If it did not
pair successfully then an 'unsuccessful' message will display. Repeat step 1.
NOTE
•If an unknown error occurred with the remote then it could've been caused by interference.
Try to remove what's causing the interference and pair it again.
•If an unknown error occurred in the remote control while the battery power is normal, you
can take out the batteries and press any key for 1~2 seconds, then the remote control can
work normally.
•The remote cannot be paired to the TV while the TV is in standby mode.