Hitec RCD OPTIMAD 2.4GHz Aircraft Receiver User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3109431
Application ID	0kgO0byhSOITXC9fXHOjMQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	59.22kB (740213 bits)
Date Submitted	2016-08-23 00:00:00
Date Available	2016-08-23 00:00:00
Creation Date	2016-05-17 17:36:45
Producing Software	doPDF Ver 8.2 Build 927
Document Lastmod	2016-08-03 13:59:59
Document Title	User Manual

Receiver Model
Size
Weight
OPTIMA D
35 x 16.8 x 5mm
4.1g
1. LED
shows current status or set up status.
(See page 2 more details)
2. , PPM or S-BUS, RSSI signal output
Help is available from the Hitec office through phone support and e-mail inquiries.
PPM or S-BUS, RSSI output
Our US office is generally open Monday thru Friday, 8:00AM to 4:30PM PST.
3. Voltage Sensor input tap(Bottom)
These hours and days may vary by season. Every attempt is made to answer every incoming service call.
Main power can be checked by this tap
Should you get voice mail, leave your name and number and a staff member will return your call.
Operation Voltage : 4.8V~7.2V (BEC from ESC can be used)
Make plans to visit the Hitec website, www.hitecrcd.com, on a regular basis. Not only is it full of specs and other
informaction about the entire Hitec product line, our FAQ pages will eventually hold valuable information and
program update about the OPTIMA D receiver.
Voltage Sensor input tap
One of the bene_ts of the extensive R/C online community is the vast wealth of archived knowledge available.
User need to have soldering direct to here to check battery voltage (4.8V to 35V)
Hitec sponsors forums on most of the popular R/C web sites where a Hitec staff_ member or representative tries
to answer all manner of product related questions.
Bus System output
Bringing together strangers with common interests is proving to be one of the greatest gifts of the internet. If
Optima D provide PPM, S-Bus. But user must select one of signal type.
past history is any guide to the future, we are certain forums will be started about the Hitec 2.4 system and
(See page 2 more details)
several are certain to stand out as valuable archives of information
RSSI Output
Via RSSI, communication sensitivity can be seen through OSD.
All Hitec products carry a two year from date of purchase warranty against manufactures defects.
Our trained and professional service representative will determine if the item will be repaired or replaced. To
provide all the necessary information we need to administrate your repair, visit our website at www.hitecrcd.com
Compatibility
- Optima D is using Hitec AFHSS 2.4GHz system, all Hitec radios can control Optima D Receiver.
and download the repair form, _ll it out and send in your item for repair.
How to Link (ID-Set)
When you purchase a radio set that Transmitter and receiver include together in the box, each device are linked
already from the factory.
If you purchase extra receivers or transmitter, you need to have Link with current your device together.
Aurora 9
Press and hold the button on the module, and turn on the transmitter*
For Aurora 9, once connect to module, press Link button in the module and turn on the transmitter. Press
Transmit “Yes” in the Aurora 9 screen and then release Link button.
1.
Press Link button in the Receiver and turn on the Receiver. Once Receiver power is on, release Link
button. After release Link button, LED will turn Blue and entered Scan mode.
2.
4.
Once BLUE LED change to solid BLUE, Fail Safe is successfully completed.
the same time BLUE LED in the Receiver also will be blinking.
5.
Please turn off the transmitter to check the operation
Now Connection is completed
3.
Turn off and On both transmitter and receiver together, Beep sounds will be spoken 4 times. This sound
also shows that connection is completed.
Aurora 9X, Flash Series
1.
Turn On the Transmitter.
2.
Select ‘Spectra’ in the System menu of Transmitter.
3.
Select RX type as “Opti&Mini”. Select ‘Binding’ and press ‘YES’.
4.
Press Link button in the Receiver and turn on the Receiver. LED will turn Blue and entered Scan mode
5.
Once Link is completed, Transmitter screen will be changed to the next step.
6.
Turn Off/On the Receiver power and check the operation. Press ‘Finish’ on the radio to complete the Link.
Signal Mode Change ( PPM, S-Bus )
Optima D provides PPM and S-BUS signal. User can choice one of PPM or S-BUS according to their FC (Flight
Control).
1.
Turn off the transmitter during this process
2.
Press “Link” button of Optima D and turn on the Power.
3.
Once BLUE LED is blinking and stop blinking, release Link button.
4.
If BLUE LED is blinking 2 times- this is PPM Mode
If BLUE LED is blinking 3 times – this is S-BUS Mode
Once press Link, Mode will be changed.
5.
BLUE LED will be blinking start slowly and then blinking rapidly.
Once connection is completed, Red LED will be on in the module. After that BLUE LED will be blinking. At
Once signal mode is selected, press and hold Link Button about 3 seconds and release.
LED will be blinking rapidly. This is confirmation sign.
FAIL-SAFE and Hold Mode Setup
FAIL-SAFE point you previously stored in the FAIL-SAFE set-up. Make sure you set the FAIL-SAFE function
properly.
If FAIL-SAFE has not been activated, the signal will switch off after the HOLD period of one second. This means
that the servos become “soft” and remain in their last commanded position under no load (this may equate to
full-throttle!), until a valid signal is picked up again.
In the interest of safety, we recommend that the FAIL-SAFE function should always be activated, and the
FAIL-SAFE settings should be selected so as to bring the model to a non-critical situation (e.g. motor idle /
electric motor OFF, control surfaces neutral, airbrakes extended, aero-tow release open, etc.).
1.
Turn On the transmitter and receiver
2.
Check the correct operation and place control stick or control toggle of transmitter to fail-safe position.
3.
Press and Hold Link button in the receiver in 6 seconds.
Cet équipement doit être installé et utilisé avec un minimum de
20 cm de distance entre la source de rayonnement et votre
corps.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Create Date                     : 2016:05:17 17:36:45+09:00
Modify Date                     : 2016:08:03 13:59:59+09:00
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Metadata Date                   : 2016:08:03 13:59:59+09:00
Producer                        : doPDF Ver 8.2 Build 927
Format                          : application/pdf
Document ID                     : uuid:77b61628-c4de-4e92-bb87-155062c6fbf5
Instance ID                     : uuid:a44bd372-f7b0-439f-a21e-e5c3eca4aa3c
Page Count                      : 3

EXIF Metadata provided by EXIF.tools