Hobbico 0205 Vusion 250 Race Quad RTF 25mW User Manual RISE0200 indd
Hobbico Inc Vusion 250 Race Quad RTF 25mW RISE0200 indd
Hobbico >
Users Manual
INSTRUCTION MANUAL WARNING Please read and understand this manual, the operation and all safety aspects required for the safe operation of the product. Before use, if you feel that this product is not for you, please return it to the place of purchase. Manual Speciications and Description Changes The instruction manual, warranties, and other associated documentation are subject to change without notice. Hobbico assumes no responsibility for inadvertent errors to this manual. © 2016 RISE, a Hobbico company. ™ RISE0200/05 INTRODUCTION Thank you for purchasing the VUSION FPV RACER. We want the time you spend with your new R/C quadcopter to be fun and successful so please read the entire manual before beginning setup. If for any reason you think this R/C model is not for you, return it to the dealer immediately. Your dealer cannot accept returns on any model after final assembly. For the latest technical updates or manual corrections for the VUSION FPV RACER please visit the Rise web site at www.explore-rise.com . If there is any new technical information, changes or important updates to this model, a “tech notice” box will appear on the page. Click the “tech notice” box to learn more. SAFETY PRECAUTIONS Failure to follow these safety precautions may result in injury to yourself and others. ● Keep your face and body as well as all spectators away from the rotating plane of the blades whenever the battery is connected. Keep loose clothing, shirt sleeves, ties, scarfs, long hair or loose objects such as pencils or screwdrivers that may fall out of shirt or jacket pockets away from the rotors. The spinning blades of a model quadcopter can cause serious injury. When choosing a flying site for your VUSION FPV RACER, stay clear of buildings, trees and power lines. AVOID flying in or near crowded areas. DO NOT fly close to people or pets. Maintain a safe distance from the quadcopter. ● Your VUSION FPV RACER should not be considered a toy. Because of its performance capabilities, the VUSION FPV RACER, if not operated correctly, could cause injury to you or spectators and damage to property. ● DO NOT alter or modify the model. Doing so may result in an unsafe or unflyable model. ● When and if repairs are necessary you must correctly install all components so that the model operates properly on the ground and in the air. Please check the operation of the model before every flight to insure that all equipment is operating and that the model has remained structurally sound. Be sure to check connectors and the propellers before each flight. Replace them if they show any signs of wear or fatigue. KNOW BEFORE YOU FLY As a new owner of an unmanned aircraft system (UAS), you are responsible for the operation of this vehicle and the safety of those around you. Please contact your local authorities to find out the latest rules and regulations. faa.gov/uas knowbeforeyoufly.org AMA We urge you to join the AMA (Academy of Model Aeronautics) and a local R/C club. The AMA is the governing body of model aviation and membership is required to fly at AMA clubs. Though joining the AMA provides many benefits, one of the primary reasons to join is liability protection. Coverage is not limited to flying at contests or on the club field. It even applies to flying at public demonstrations and air shows. Failure to comply with the Safety Code may endanger insurance coverage. Additionally, training programs and instructors are available at AMA club sites to help you get started the right way. There are over 2,500 AMA chartered clubs across the country. Contact the AMA at the address or toll-free phone number that follows. Academy of Model Aeronautics 5151 East Memorial Drive Muncie, IN 47302-9252 Tele. (800) 435-9262 Fax (765) 741-0057 Or via the Internet at: www.modelaircraft.org IMPORTANT: Two of the most important things you can do to preserve the radio controlled aircraft hobby are to avoid flying near full-scale aircraft and avoid flying near or over groups of people. BATTERY WARNINGS ● ALWAYS unplug your battery from either the charger or quadcopter after use. NEVER store your quadcopter with the battery plugged into the quadcopter. ● DO NOT attempt to charge your battery if it becomes swollen or hot. ● The VUSION FPV RACER does not have a voltage cutoff/failsafe. When the alarm sounds, land the quad and disconnect the battery. ● It is best to store your batteries in a cool, dry location at 1/2 charge (11.4V). Storing a fully discharged battery may cause irreversible damage to the battery. ● NEVER disassemble, puncture or modify the battery pack in any way. ● NEVER allow the battery temperature to exceed 150° F [65° C]. ● If your battery begins to swell or “puff” during charge or discharge or becomes damaged in any way, stop using it. WARRANTY RISE™ guarantees this kit to be free from defects in both material and workmanship at the date of purchase. This warranty does not cover any component parts damaged by use or modification. In no case shall RISE’s liability exceed the original cost of the purchased kit. Further, RISE reserves the right to change or modify this warranty without notice. In that RISE has no control over the final assembly or material used for final assembly, no liability shall be assumed nor accepted for any damage resulting from the use by the user of the final user-assembled product. By the act of using the user-assembled product, the user accepts all resulting liability. If the buyer is not prepared to accept the liability associated with the use of this product, the buyer is advised to return this kit immediately in new and unused condition to the place of purchase. To make a warranty claim, send the defective part or item to Hobby Services at this address. Hobby Services 3002 N. Apollo Dr., Suite 1 Champaign, IL 61822 USA 217-398-8970 ext#6 productsupport@hobbyservices.com Include a letter stating your name, return shipping address, as much contact information as possible (daytime telephone number, fax number, e-mail address), a detailed description of the problem and a photocopy of the purchase receipt. Upon receipt of the package the problem will be evaluated as quickly as possible. FEATURES ● ● ● ● ● ● 600TVL FPV Camera Entry Level 250 class racing quad ● 200mW or 25mW VTX Oneshot125 speed controls ● On Board DVR 2280kV 1806 size Brushless motors Ready to Fly, no building required Flight Controller is pre-programmed, no setup needed DIMENSIONS Size: Width: Length: Height: Prop: Blade Length: Empty Weight: 250mm (9.8in) diagonally motor to motor 241mm (9.5in) 252mm (9.9in) 69mm (2.7in) ● RTF RISE VUSION FPV RACER 5 x 4.5 ● Transmitter 127mm (5in) ● FPV Goggle with Monitor 502g (17.7oz.) without battery ● Monitor Antenna CONTENTS ● Goggle Foam Liner ● 1500mA 3S LiPo ● LiPo Charger w/AC Adapter FPV VTX Antenna FPV Camera Memory Card Slot SETUP The VUSION FPV RACER is completely assembled. All the bolts have been set to the proper torque and have thread locking compound applied where needed to keep them secure. FPV ANTENNA Always attach the FPV VTX antenna before connecting the battery to the Vusion. If the quadcopter is operated without the FPV antenna, the VTX could be damaged. BATTERY CHARGING Plug the AC wall adapter into a 120V outlet and connect the balance charger to the wall adapter. The power LED will illuminate solid RED. Plug the white balance plug on the battery to the 3S port on the charger. When charging, the charge status LED will illuminate solid RED. When charge is complete the LED will change to solid GREEN. Typical charge time of a depleted battery is approximately 2 hours. NOTE: A blinking red charge status LED indicates a charging error. ● NEVER leave the battery unattended while charging. ● ALWAYS unplug the charger from the outlet and the battery when charging is complete. ● NEVER charge a puffed or damaged battery. NOTE: It is normal for the charger to get warm during the charging process BATTERY INSTALLATION Pull on the edge of the battery tray cover to unsnap it from the Vusion’s frame Pull Remove the cover and install the battery. Tuck the balance plug down next to the battery and replace the cover. RADIO SYSTEM Insert 4 AA batteries in the battery compartment in the back of the transmitter. Turn on the transmitter and connect the battery to the Vusion. The quadcopter should beep twice when it is linked to the transmitter. NOTE: Always turn the transmitter on first. FLYING MOTOR ARMING While the throttle is at its lowest setting, hold the yaw control (left stick) to the right to arm the motors. Holding the yaw control to the left while the throttle is at its lowest setting will disarm the motors. The motors will also shut off if the throttle is its lowest setting for more than 3 seconds. FLIGHT MODES The Vusion has 3 flight modes. Mode 1: This mode has autolevel, mild roll rates and very limited tilt angles. Ideal for the pilot who is moving up from an entry level quadcopter. FLIGHT MODES Switch Position Stability Mode Tilt Angle Roll Rate Mode 1 Away Stability 30 Low Mode 2 Middle Stability 45 Medium Mode 3 Forward Rate 360 High Mode 2: This mode still has autolevel, but has higher roll rates and a high tilt angle setting. This mode is for the more experienced pilot. Mode 3: This mode (rate mode) has no limits on tilt and faster roll rates. The quad will not autolevel in this mode. This mode offers the most maneuverability but requires the pilot to be able to control the attitude of the quadcopter themselves. It normally takes a week or two of practice to learn to fly rate mode. Start by flying Line of Sight (no FPV) until you can comfortably control the quad. If possible, fly in an open area over tall grass to minimize damage to the Vusion when you crash. When you are comfortable making a flip in this mode, you should be ready for FPV. TAKEOFF AND LANDING Turn on the transmitter and connect the flight battery to the VUSION FPV RACER. Place the quadcopter on a level surface and let it sit for 10 seconds to let the flight controller set up the gyros. Calibrate the sensors before your first flight (page 10). Arm the motors by holding the yaw control to the right for a second, and back to center. The motors will start spinning when the motors are armed. Advance the throttle at a moderate speed to take off. To land, hover the Vusion over the landing spot and slowly reduce the throttle. When the quadcopter is on the ground, disarm the motors by holding the left stick at its lowest point and move to the left. Unplug and remove the battery. FPV The Vusion has a built in FPV camera and 8 channel VTX that transmits on Raceband. The monitor will have to be set to the correct channel to display the feed from the camera. 1. Power up the Vusion and raise the camera by pushing down on camera icon. 2. Attach the monitor antenna and turn on the FPV monitor. 3. If the monitor is not displaying a signal from the Vusion, hold the “B” button on the monitor for 2 seconds and release it. The monitor will scan all the channels and lock onto the closest signal. 4. Place the monitor in the cradle on the transmitter or inside the goggle. If the VTX must use a different FPV channel, remove the rear cover by pushing down on the edge of the cover and sliding it back. Push Tap the red button to cycle through the 8 channels that are available. To see current band, channel and frequency on the monitor, select Band E with the “B” button and tap the CH button until the screen displays the feed from the camera. Flying FPV is more difficult than Line of Sight because it is difficult to determine altitude with just the camera. Practice in an open area with a spotter. If possible, fly over tall grass to minimize damage when you crash. When you are comfortable flying in an open area, practice flying a pre-set course. This will help you learn to corner faster. FAILSAFE/BEACON The Vusion will autoland and start beeping when the signal from the transmitter is lost. This feature can be used as a beacon to help locate the quadcopter when it has crashed by turning off the transmitter. VUSION CAMERA Video clips and still images from the Vusion’s camera can saved to an on board micro SD memory card (not included). VIDEO Pressing the video button will start and stop the video. The timer in the lower left corner of the monitor will be on while video is being recorded. The DVR will automatically save the video to the memory card every 4 minutes and start a new video. To avoid losing any of the video after landing, always stop the recording and wait 15 seconds before unplugging the battery from the Vusion. STILL PHOTO Pressing the “Picture” button will capture a still photo. The camera will not save the photo if a video is being recorded. BATTERIES The VUSION FPV RACER uses a 1500mA 3 cell LiPo. Typical flight time is 5 to 8 minutes depending on the flying style. The flight controller does have a low voltage cutoff to protect the LiPo from damage. There is an alarm that will start beep and the rear LED panels will flash when the battery voltage drops to 10.5V. You should land the quadcopter as soon as possible when you hear or see the alarm to avoid damaging the battery. The Vusion will autoland when the battery voltage gets below 9.7V. The flight battery should always be recharged before it is stored. Warning: Your battery life will be reduced and the battery can be damaged any time the battery voltage is below 9V. Charging a LiPo battery that is damaged in any way can pose a fire hazard. EXTERNAL RECEIVER WARNING: Remove the props before connecting an external receiver to the Vusion. The VUSION FPV RACER can be adapted to use an external receiver (one wire for each channel) with the RISE2509 Cable Set. Note: The stock transmitter must be used if recording photos or video by the on board DVR is desired. The transmitter should have a new model set up using the following chart as a guide. MODEL TYPE: Airplane CHANNEL ASSIGNMENTS SWITCH ASSIGNMENTS - Ch 5 Channel Direction Expo AUX -100% Stability 1 Aileron normal End Points Dual Rates 100/100 80/100 -20/0 AUX 0% Stability 2 Elevator reverse 100/100 80/100 -20/0 AUX 100% Rate Throttle reverse 100/100 Rudder reverse 100/100 80/100 -20/0 Gear normal 100/100 AUX reverse 100/100 NOTE: Spektrum/JR systems should have opposite directions. If your transmitter can set failsafe values for all the channels, set the roll & pitch channels to midstick and the throttle to its lowest setting to stop the motors. For transmitters that only set failsafe on the throttle channel, set the throttle to its lowest setting. 1 Black (Ground) 2 Red (+5V) 3 White 4 Purple 5 Yellow 6 Green 7 Yellow 8 Black Ground +5V Aux (CH 6) Gear (CH 5) Rudder Throttle Elevator Aileron RECEIVER ADAPTER PLUG EXTERNAL RECEIVER CONNECTIONS Plug the 8 wire cable into the receiver as shown. Channel 6 must be assigned to a switch so it can be used to change flight modes. Turn on the transmitter and connect the battery to the Vusion. Perform a sensor calibration as described in Maintenance Section to verify that the control board is receiving signals from the receiver. The quadcopter will not enter the calibration mode if the receiver is wired incorrectly. Arm the motors by holding the yaw control to the right. Advance the throttle and check for a motor not running. Bring the throttle back down to its lowest setting. The motors should stop after 5 seconds. MAINTENANCE PROPELLER INSTALLATION Please refer to this diagram when installing or replacing the propellers to make sure each is installed on the correct motor. CW – clockwise rotation when viewed from above (there is an “A” on the arms and the propellers). CW PROP FRONT CCW PROP CCW – counter clockwise rotation when viewed from above (there is a “B” on the arms and the propellers) CCW PROP SENSOR CALIBRATION 1. Calibrate the sensors before the first flight. Turn on the transmitter. Center all the trim adjustments. To center the trim settings, hold down one side of the trim button until you hear a long beep. If the controller stops beeping, release the trim button and hold down the other side. 2. Place the Vusion on a level surface and link the quadcopter with the controller. 3. Press and hold the right stick in its lower right corner. 4. Move the left stick down and to the right. When the LEDs on the Vusion start to flash, release both sticks. The LEDs will stop flashing when the calibration is complete. 10 CW PROP LINK TRANSMITTER If the Vusion does not make a double chime when it is powered up and the transmitter is on, it may need to be relinked. 1. Turn off the transmitter. 2. Remove the rear cover. Press down on the rear edge and slide the cover out of the frame. 3. Connect the battery to the Vusion. 4. Press and hold the red button until the red and white LEDs on the board start flashing. 5. Turn on the transmitter. The board should make the second chime immediately. REMOVE FRONT MOTOR ARM REMOVE REAR MOTOR ARM 11 Push SEPARATE FRAME To remove the Camera, VTX or Control Module, the frame must be separated. All 4 arms must be removed first. 12 SPARE PARTS 10 11 12 13 14 15 16 17 18 19 20 21 22 23 RISE2020 RISE2009 RISE2010 RISE2019 RISE2001 RISE2017 RISE2018 RISE2007 RISE2025 RISE2015 RISE2006 RISE2004 RISE2003 RISE2005 RISE2000 RISE2026 RISE2022 RISE2002 RISE2013 RISE2011 RISE2012 RISE2014 RISE2016 RISE2008 RISE2021 RISJ2000 FPV VTX Antenna Prop Nuts CW/CCW Props CW/CCW 2 Yellow/2 Black Camera VTX CASE Top Cover 25mW VTX Camera 200mW VTX Camera FC Board Module with Arm sockets Control Board Dampers (4) Frame Left and Right L/R Arm CCW Motor ESC L/F Arm CW Motor ESC R/F Arm CCW Motor ESC R/R Arm CW Motor ESC Canopy Motor Shields (4) LiPo 3S 11.1V 1500mAH Battery Cover L/R Arm Top and Bottom L/F Arm Top and Bottom R/F Arm Top and Bottom R/R Arm Top and Bottom LED Arm Covers (4) Landing Gear (4) with mounting screws (12) Screw Set Transmitter 6-Channel GOGGLES PARTS TACZ5610 FPV-G1 Head Strap TACZ5612 FPV-G1 Face Plate Foam MONITOR PARTS AND ACCESSORIES TACZ5600 FPV-RM2 Sun Shield TACZ5602 FPV-RM2 Tripod Mount TACZ5300 FPV 5.8GHz RP-SMA TX Antenna Short 110mm 0.95dBi TACZ5305 FPV 5.8GHZ Cloverleaf Antenna 3dBi OTHER OPTIONAL PARTS AND ACCESSORIES RISE2509 RX Flight control board extension cable TACZ1010 4G Class 10 Micro Memory Card TACZ5604 USB Micro SD Card Reader TACL0625 TR625 6-Channel SLT Receiver Twin Antennas TACJ2650 TTX650 6-Channel SLT Computer Transmitter DTXP4620 Duratrax Li-24 2S-4S AC Balance Charger 13 14 ™ BATTERY PRECAUTIONS The RISE Vusion uses a lithium polymer (LiPo) battery. Follow these precautions to ensure safe and trouble-free operation. • ALWAYS disconnect the battery from the quadcopter when not in use. • Do not attempt to use this charger with NiCd or NiMH battery packs. • Do not attempt to use a damaged battery. • This product contains a LiPo battery that must be recycled or disposed of properly. • Do not leave the charger unattended while charging. Disconnect the battery and unplug the charger immediately if either becomes hot! However, it is normal for the charger to get warm. • Disconnect the battery from the charger and carefully move the battery to a ireproof location if the battery begins to swell or smoke! • Never allow the battery temperature to exceed 140° F [60° C]. • Do not attempt to charge a battery if it is swollen or hot. • Do not place the charger or any battery on a lammable surface or near combustible materials while in use. • Never disassemble or modify pack wiring in any way or puncture cells. • Never charge inside a vehicle. • Always disconnect the battery and unplug the charger when not in use. • Land your model immediately when the LEDs lash to indicate that the battery power is low. Recharge the battery before attempting another light. A dangerous situation can occur when attempting to recharge an over-discharged battery! • ALWAYS keep a supply of sand accessible when charging. Dumping sand on the battery will extinguish a LiPo chemical ire. • ALWAYS KEEP OUT OF REACH OF CHILDREN FCC PRECAUTIONS FCC RADIATION EXPOSURE STATEMENT CE COMPLIANCE INFORMATION FOR THE EUROPEAN UNION INSTRUCTIONS FOR DISPOSAL OF WASTE EQUIPMENT BY PRIVATE USERS IN THE EUROPEAN UNION: This symbol on the product or its packaging indicates this product must not be disposed of with other household waste. Instead, it is the user’s responsibility to dispose of their waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city ofice, your household waste disposal service or location where you purchased the product. DECLARATION OF CONFORMITY: Product: RISE 2.4GHz 6-Channel Tx Rx Item number: RISJ2000 J2000 Equipment class: 1 J2000 transmitter: The objects of the declaration described here are in conformity with the requirements of the speciications listed below, following the provisions of the European 2014/35/EU Low Voltage Directive: EN 60950-1:2013 Safety The objects of the declaration described here are in conformity with the requirements of the speciications listed below, following the provisions of the European R&TTE directive 1999/5/EC: EN300 328 V1.9.1. Technical requirements for radio equipment ETSI EN 300 328 V1.9.1 (2015-02); ETSI EN 301 489-1 V1.9.2 (2011-09); ETSI EN 301 489-3 V1.6.1 (2013-08); EN 62479:2010 General EMC requirements for radio equipment This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Product: RISE 5.8GHz 25mW VTx Any Changes or modi f i cat i ons not expr essl y appr oved by t he par t y r esponsi bl e f or compl i ance coul d voi d t he user ' s aut hor i t y t o oper at e t he equi pment . This device complies with part 15 of the FCC rules. Changes or modiications not expressly approved by Tactic will void the user’s authority to operate this Tx. Operation is subject to the following two conditions: Technical requirements for radio equipment ETSI EN 300 440-2 V1.4.1 (2010-08) ; ETSI EN 301 489-1 V1.9.2 (2011-09); ETSI EN 301 489-3 V1.6.1 (2013-08); EN 62479:2010 General EMC requirements for radio equipment (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help Hobbico, Inc. 2904 Research Road Champaign, IL USA 61826 Distributed in Europe by Revell GmbH D-32257 Bünde Germany RISE J2000 Transmitter FCC ID: IYFJ2000 RISE 25mW VTx FCC ID: IYF0205 MADE IN CHINA © 2016 RISE, a Hobbico company. RISE0200/05 Addn1
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V4.4 (128-bit) User Access : Print, Extract, Print high-res Author : ledwards Create Date : 2016:09:21 17:03:13-05:00 Modify Date : 2016:09:30 13:45:52-07:00 Has XFA : No XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Creator Tool : Adobe InDesign CC 2015 (Windows) Metadata Date : 2016:09:30 13:45:52-07:00 Producer : Acrobat Distiller 15.0 (Windows) Format : application/pdf Title : RISE0200.indd Creator : ledwards Document ID : uuid:1f3a4dd2-bd46-4ce6-83d9-6466c4ffec13 Instance ID : uuid:05744ec8-dab6-4801-a277-40b2984ceca6 Page Count : 15EXIF Metadata provided by EXIF.tools