user manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 302712 |
| Application ID | 7orieklJ73eRLBEzzuIEyA== |
| Document Description | user manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 38.74kB (484200 bits) |
| Date Submitted | 2003-02-13 00:00:00 |
| Date Available | 2003-02-13 00:00:00 |
| Creation Date | 2003-02-05 10:00:30 |
| Producing Software | Acrobat Distiller 4.0 for Windows |
| Document Lastmod | 2003-02-07 12:00:13 |
| Document Title | user manual |
™ PowerBrute by Instruction Manual for Models HCAC0491 and HCAC0492 IMPORTANT: Please read all instructions thoroughly before operating your vehicle. Box Contents General Safety Precautions R/C MicroSizers are recommended for ages 8 and older. To ensure the safety and fun of young modelers, please follow these operating instructions and general safety rules: · · · · · · · Adult supervision is recommended. Do not allow children under age 3 to play with the R/C MicroSizers PowerBrute or radio transmitter. The model contains small parts which could accidentally be swallowed and cause suffocation. Keep hair, loose clothing, face and fingers away from the tires and wheels while the model is running. The transmitter's antenna could also cause injury if played with violently or looped around the neck. Never operate your R/C MicroSizers PowerBrute on streets or in any areas where full-size vehicles are. Do not pick up your R/C MicroSizers PowerBrute when it is in motion. R/C MicroSizers PowerBrutes were designed for indoor use only. Outdoor use may lead to failure due to dirt and dust. · · · · · Do not run your R/C MicroSizers PowerBrute on rugs or carpeting. The fibers may become tangled in the model and cause damage or failure. Never charge, run or store your R/C MicroSizers PowerBrute in a location subject to high temperatures, low temperatures or high humidity. Do not store in direct sunlight. To avoid electronic malfunction, do not allow the truck to become wet. Short circuits will produce a very strong electrical current. Should your R/C MicroSizers PowerBrute become wet, stop using it immediately. Never attempt to disassemble or solder the model. Do not put it into fire. Do not drop your R/C MicroSizers PowerBrute from high places. R/C MicroSizers Service Center We're eager to help you get the most enjoyment from your R/C MicroSizers. If you have any problems with assembly or operation, please do not return your model to the store. Check our website first. Many easy solutions are available there 24 hours a day, 7 days a week. www.microsizers.com Or, call the R/C MicroSizers Service Center at 1-866-HOBBICO (1-866-462-2426), Monday through Friday, 9:00 am - 4:00 pm Central Time. We've backed your model by a 90-day satisfaction guarantee, so you can be confident of its quality. Happy driving! How to install the batteries How to assemble your R/C MicroSizers PowerBrute STEP 1: Apply the stickers. ➊ Remove the battery cover screw with a Phillips screwdriver. ➋ Install your batteries with the correct polarity. This transmitter requires 2 "AA" alkaline batteries. Never use other types of batteries. Place the numbered stickers at the locations shown in the illustration. ➌ Replace the battery cover and tighten the screw. How to charge the vehicle STEP 2: Mount the body. CHARGER DOOR ON/OFF SWITCH TRANSMITTER ➊ Set the transmitter switch to ON. ➊ Thread the antenna through the hole in the top of the body. ➋ ➀ Fit the slot in the rear of the body over the tab at the back of the chassis. ➁ Then snap the front in place. CHARGER COVER As a reference point, start by inserting this pin in the middle of this slot. ➌ For maximum control (8 to 10 ft. [2.4-3.0m] range), extend the antenna wire straight up. STEP 3: Install the tool attachment. ➋ Open the cover on the right side of the transmitter. Position the model parallel to the transmitter with the headlights pointing up. Use the illustrations above to align the model with the pins on the transmitter and snap it into place. ➊ Pull to remove the front grille. ➋ Press in and push up at the front to remove the hood. Reverse these steps to reattach the hood and grille. ➌ Fit the rear of the tool attachment against the chassis tab located directly below the body’s front windshield. Snap the tool attachment down to fit securely onto the chassis. Make sure that the tool snaps into place firmly. If it does not operate properly, try installing it again. Reverse these steps to remove the tool. ☞ IMPORTANT This raised knob on the chassis must be in the slot on the tool attachment’s moving arm. CHARGE LED ➌ The metal contacts on the model and the charger must make contact. While charging, keep pressing the chassis against the transmitter and make sure the CHG light is on. ➍ The LED (CHG) on the front of the transmitter will light for 45 seconds. When it goes out, the battery has completed charging. If the model is attached before the transmitter is switched ☞ on, it will not charge. Important Battery Information Model Battery Care Transmitter Battery Care A rechargeable battery has been built in to the main body of the model. Using the battery incorrectly will cause it to leak, rupture or ignite. Follow these precautions: Always use AA alkaline batteries. If improper batteries are used in the transmitter, they may become hot, leak and may rupture. Follow these precautions: If your R/C MicroSizers PowerBrute has been unused for a long period or you are charging its built-in battery for the first time, the battery may not charge to full capacity. This does not indicate battery failure. Recharging and running the model 4 or 5 times will gradually lengthen run times. Never use rechargeable batteries, such as NiCds, in the transmitter. · · · · · Fully discharge the battery by running the truck before recharging. Charge the battery only when the truck is NOT running. To prevent overcharging, never recharge a battery which has already been fully charged. This will not increase running speed. Recharge the battery only with the transmitter's built-in charger. If the chassis becomes warm, let it cool before running again. This product uses a NiCd battery. NiCd batteries are recyclable, and a valuable resource. To dispose of the battery, remove it and take it to a recycling center. · · · · · · · Do not mix different types of batteries, or old and new batteries. When changing batteries, replace ALL of the old batteries with new ones. Make sure the batteries are installed with the correct polarity as shown in the battery compartment. Do not charge or disassemble your transmitter batteries. Never allow them to become hot or to burn. To avoid short-circuits, avoid getting them wet. If liquid from inside the batteries contacts your skin or clothes, wash them with water. If leaked battery fluid gets into your eyes, flush them immediately with cool water and seek medical attention. Do not rub eyes. You can race about 50 times with new AA alkaline batteries. How to drive STEERING CONTROL THROTTLE CONTROL ANTENNA STRAIGHT LINE TRIM CONTROL ON/OFF SWITCH ➊ Gently pull up the antenna by hand. Never attempt to extend the antenna by turning or pushing the dial on the back of the transmitter. ➋ Turn on the transmitter switch. Throttle (left toggle control) - Move the truck forward by pushing up, or reverse by pushing down. Steering Wheel (right toggle control) - Steer the front tires left or right by pushing the right toggle control. By operating the toggle controls on both the right and left simultaneously, the truck can move forward-right, forward-left, reverse-right, or reverse-left. To run two R/C MicroSizers cars or PowerBrutes together, each must be on a different frequency. ☞ If the truck does not go ☞ straight when pushing the left toggle control up, move the trim lever on the bottom of the chassis to the left or right to make adjustments. How to change the drive motor Optional motors (available separately) can be installed for higher performance. ➊ Pull off the heatsink with your fingers. HEATSINK Shaded area must be toward the front of the chassis. ➋ Pull out the motor. ➍ When installing a motor, make sure that the motor contacts are in the proper position as shown ➌ Install a new motor. After running How to operate the tool attachment ANTENNA WINDER ACTION ➊ Press the transmitter’s ACTIVATOR Action Activator button to move the tool up and down. ➊ Turn the winder on the back of the transmitter to store the antenna. Do not force the antenna back inside the transmitter by hand. ➋ Switch the transmitter off. Always turn the switch off when not in use to extend your battery life. Troubleshooting Symptom Probable cause Correction TRUCK DOES NOT RUN Transmitter battery capacity is low, or no batteries have been installed. Install two brand-new "AA" alkaline batteries (they MUST be alkaline). Transmitter is not switched on. Move the switch of the transmitter to "ON". Then, charge the truck and race. Model is not assembled correctly. Reassemble it correctly, paying close attention to the instruction steps. Radio signals don't seem to reach the model. Fully extend the antenna. Maximum range is 8 to 10 feet [2.4-3.0m]. Motor/battery life has expired. Replacement motors are sold separately. Is there dust on the tires and/or wheels? Remove dust/lint from the tires and wheels. Is the trim lever in a straight position? Adjust the trim lever until the truck moves straight ahead. Are you driving your truck on a rug? R/C MicroSizers PowerBrutes are not intended for running on rugs or carpets. Interference from reflected radio waves Turn off electronic devices or move to a different location. Are you running with another truck on the same radio frequency? Each truck must be on a different frequency. TRUCK DOES NOT OPERATE PROPERLY TRUCK MOVES UNCONTROLLABLY This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. Meets Canada 210 requirements. Carrier Frequency: 27.145MHz Power: 2µV/m Carrier Frequency: 49.860MHz Power: 4µV/m Customize your R/C MicroSizers PowerBrute Use the optional parts and accessories listed here (available separately) to boost the performance of your R/C MicroSizers. MicroSnap Motor 1.0 MicroSnap Motor 1.6 MicroSnap Motor 2.2 MicroSnap Motor 2.6 Digital Lap Counter . MicroSizers Pit Case 27MHz Speed Set . . 49MHz Speed Set . . .HCAC1302 .HCAC1306 .HCAC1301 .HCAC1305 .HCAP0002 .HCAP0003 .HCAC1104 .HCAC1105 Toyota Celica Body Set (silver and clear, 2 bodies) Nissan Skyline R34 GT-R Body Set . . . . . . . . . . . (yellow and clear, 2 bodies) Mazda RX-7 Body Set (black and clear, 2 bodies) Hop-Up Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Maintenance Kit . . . . . . . . . . . . . . . . . . . . . . . . . . Guide Rail & Pylon Set . . . . . . . . . . . . . . . . . . . . . . .HCAC1009 . .HCAC1010 .HCAC1011 .HCAC1313 .HCAC1314 .HCAC1203 Stage a battle of the PowerBrutes The optional R/C MicroSizers PowerBrute Arena (sold separately) provides the perfect test of your driving skills and a stage to see whose PowerBrute is the MOST powerful! · · · Navigate narrow bridges and rugged platforms. Reach the rotating central platform for a fierce Lug vs. Scrape showdown! Arena sections can be rearranged for endless variety of maneuvering challenges. Entire Contents © Copyright 2003 V1.0 Printed in China HCAZ0421 for HCAC0491-0492
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Create Date : 2003:02:05 10:00:30 Producer : Acrobat Distiller 4.0 for Windows Modify Date : 2003:02:07 12:00:13-05:00 Page Count : 4EXIF Metadata provided by EXIF.tools