Hobbico CME C-me Flying Camera User Manual HCAE10xx online instr indd

Hobbico Inc C-me Flying Camera HCAE10xx online instr indd

Users Manual

INSTRUCTION MANUAL
BATTERY PRECAUTIONSThe C-me uses a lithium polymer (LiPo) battery. Follow these precautions to ensure safe and trouble-free operation.● ALWAYS turn off the C-me when it is not in use.● Do not attempt to use a damaged battery.● This product contains a LiPo battery that must be recycled or disposed of properly.● Do not leave the C-me unattended while charging. It is normal for the drone to get warm. Disconnect the C-me immediately if it becomes hot!● Never disassemble or modify the C-me wiring in any way or puncture battery.● Always unplug the charge cable when not in use.● After the C-me has landed because the battery is exhausted, recharge the battery before attempting another  ight.● ALWAYS KEEP OUT OF REACH OF CHILDRENSAFETY PRECAUTIONSFollow these safety precautions when operating this or any drone.● Adult supervision required.● Before  ying, go to www.knowbeforeyou y.org.● Do not touch the spinning blades or  y over another person’s head.● Keep your face and body as well as all spectators away from the rotors whenever the battery is connected.● Stay clear of trees and power lines. AVOID  ying in or near crowded areas. DO NOT  y close to people, children or pets. Do not  y in windy conditions or when the C-me may get wet from rain or snow.● Your C-me should not be considered a toy, but rather a small, working model. If not operated correctly, the model could possibly cause injury to you or spectators and damage to property.● You must check the operation of the model before every  ight to ensure that the model has remained structurally sound.● Do not alter or modify the model, as doing so may result in an unsafe or un yable model.● Do your part in preserving the integrity of the RC hobby. Know the boundaries of your  ying area and ALWAYS respect the privacy of others.
PRODUCT FEATURES● Portable: Fits in your pocket● Simple Operation● GPS Controlled Stability● 8 megapixel 1080p camera, same as on the iPhone6● One button 360° Panoramic Video● One Button Take Off/Landing● Auto Return to Home● Find Me/Follow Me● Instant Sharing of Social MediaCONTENTSC-me Sel e DroneMicro USB Charge Cable2Amp AC to USB AdapterSpare Propellers (4)Quick Start GuideSPECIFICATIONS*Weight: 4.97 oz. [141g]Width: 6.26 in. [159mm]Length: 6.06 in. [154mm]Height: 0.98 in. [25mm]Prop Size: 29.1 in. [74mm]Size: 7.67 in. [195mm] diagonal motor to motorFlight Time: Approximately 10 minutes(*With arms extended, not including the propellers.)LIMITED WARRANTYPLEASE DO NOT RETURN YOUR PRODUCT TO THE STORE. This warranty speci cally does not cover crash damage, misuse or abuse. Please refer to the warranty package for more details about coverage. To make a warranty claim, please contact our product support team at 1-217-398-8970 option 6 or e-mail us at helihotline@greatplanes.com. If requested by Product Support, please send defective product to:Hobby Services3002 N Apollo Dr., Suite #1Champaign, IL 61822Please include a note about the problem, your contact information, and a copy of the receipt. This warranty applies only if the product is operated in compliance with the instructions and warnings provided with each model. Hobbico assumes no liability except for the exclusive remedy or repair of parts as speci ed above. Hobbico shall not be liable for consequential or incidental damages. Some states do not allow the exclusion of consequential or incidental damages so the above exclusion may not apply to you. This warranty gives you speci c legal rights and you may also have other rights which vary from state to state.
APPDownload the latest version of the C-me app from the App Store or Google Play.Apple and the Apple logo are trademarks of Apple, Inc., registered in the U.S.and other countries. App Store is a service mark of Apple Inc. Android™ and Google Play are trademarks of Google Inc.Wi-Fi® and Wi-Fi Alliance® are registered trademarks of Wi-Fi Alliance.The C-me can be linked to two phones at the same time. The rst phone to linkwill have directional control. The second phone will only be able to monitor thefeed from the camera.CAMERAVIDEO RECORD360° PANORAMIC VIEWEMERGENCYFLASHGALLERY SETTINGSFOLLOW ME/FIND MEDIRECTIONAL CONTROLW/INCREMENTAL TRIMALTITUDE SLIDE BARINSTANT SHAREINSTANT SHAREMEMORY CARD CAPACITYBATTERY CHARGE/LIFEWI-FI STRENGTHSATELLITE SIGNALSAFETY UNLOCKONE-TAP TAKEOFF/LAND
Camera A tap on the Camera button captures a still photograph. Push and hold to access the Self-Timer and Burst mode functions for the camera. Please refer to the Photo/Video section for more details.Video Tapping this button Video button starts/stops recording a video.Panoramic View Available only in Outdoor Mode. Automatically starts a video recording, rotates the C-me 360° within 20 seconds, and stops the video.Emergency Tapping this button will make the C-me land quickly without returning to home. The Directional Controls can be used to guide the C-me while it is landing. Holding this button will stop the motors immediately.Instant Share Pressing these buttons before capturing a photo or making a video will share the media with the desired social media site. Select the desired Instant Share link and the options for captions in Settings.Flash Press the Flash Button to cycle through the three Flash modes.1. Always on. This is the default mode and is recommended because the LED can be used determine the orientation of the C-me.2. Off with camera  ash. This mode turn the LED off except when capturing a photo.3. Always off.Altitude Slide BarSlide this control up or down to change the C-me altitude. When the control is released, the C-me will hover at the selected height.Directional ControlsMove the inner circle in the desired direction with your thumb to change the C-me drone’s position. This control will be more sensitive when  own in the Outdoor Mode.Swiping the center of the screen will yaw the C-me. This control can be used to point the camera away from the pilot.Memory Card Capacity When an optional memory card is loaded on the C-me, the available free space is displayed. The C-me can use a micro memory card with a capacity of 2 to 32 GB. (A memory card is not required for operation. However, if you desire high quality images and video, we recommend using a card.)Battery Charge/Life The battery life remaining is displayed by this indicator.White indicates the charge is above 40%Red (steady) indicates the charge is between 40% and 20%Red ( ashing) indicates the charge is below 20%.
Wi-Fi Signal Strength This icon will be white with an “X” when there is no Wi-Fi connection. The icon will be green without the “X” when the app is connected to the C-me.GPS Satellite This icon will show how many satellite signals are being received. The C-me has to receive at least 6 satellite signals and the Indoor Mode setting must be “off” before it will enter Outdoor Mode. When Outdoor Mode is active, the following changes are made● The status LED on the top of the C-me will start  ashing● Control sensitivity is increased● GPS enhanced stability is active● 360° button is active● Land Button activates the return to the launch point and land (RTL) function● C-me Button in the app activates the Follow Me ModeSafety Unlock Tap and hold this button for 2 seconds to unlock the Take Off button. This button will lock again if not used within 5 seconds.Take Off Tap this button when it is green (unlocked) to take off. The pilot should keep a thumb on the Directional Control to guide the C-me to the desired hover point.Land The Take Off button will change to a Land button after the C-me takes off. Tapping this button will make the C-me slowly land.When the C-me is in the Outdoor Mode, it will climb to 3 meters and start to RTL (Return To Launch). If C-me is performing a RTL, moving the Directional Control will stop the RTL procedure and hover.When the C-me is in the Indoor Mode, the Directional Control can be used to guide the drone to a speci c landing area.When the battery charge level drops to 10%, the C-me will automatically RTL. If indoors, it will land straight down.Gallery Tapping this button will display the images and videos that have been created by the C-me and stored in Photo Gallery on the mobile device. Tap the thumbnail to view, delete or play a video.This button does not access any of the  les stored on the option memory card. Those  les must be viewed on a computer.NOTE: Files stored on a memory card will be larger and have more detail than what is stored on the phone.
Settings This button opens1. Instant Share Settings where the social media links are selected2. Camera settingsA. White BalanceB. ExposureC. ContrastD. BrightnessE. Factory default settings for the camera3. Device settingsA. Change the Wi-Fi network name and passwordB. Reset all the app settings back to the factory default values4. Help screensA. C-me Quick Start GuideB. Help section which has guides for the following subjects i. Basic Operation (Please review this section before  ying the C-me.)ii. Taking Picturesiii. Videoiv. 360°Panoramic Videov. Flash usagevi. Emergencyvii. Share (Instant Share Buttons)viii. Equipment Usage (Memory Card and Battery Life indicators)ix. Take OffC. C-me ManualD. Compass CalibrationE. Find MeF. Contact Us linkG. C-me website link5. Wi-Fi (Android app only) This section allows you to turn on the phone’s Wi-Fi and select or setup the C-me network connection without leaving the app.6. Calibration procedures have guides to help correctly calibrate the sensors.A. Compass Calibration is for calibrating the compass on the C-me which should be done every time the drone is used in a new location.B. Accelerometer Calibration is for calibrating the accelerometers which should be done any time the C-me will not remain in a stable hover.7. Full Screen Mode – sliding this button the right activates this mode. When active, it removes the buttons and controls from the screen after a few seconds of inactivity. Tapping the screen will make the buttons and controls appear again.8. Indoor Mode – Sliding this button to the right keeps the C-me in the Indoor Mode even when it is outside and receiving GPS satellite signals. The following conditions are set when Indoor Mode is active.A. Control sensitivity is decreasedB. GPS enhanced stability is disabledC. Panoramic View is disabledD. Return to Home when landing is disabledE. The C-Me button in the app activates just the Find Me mode
Follow Me/Find Me Indoors: Tapping this button turns on the Find Me mode so the C-me will always point towards the pilot. The Directional Controls are used to position the drone. Small adjustments to the camera’s direction can be made by slowly turning the phone while in the Follow Me mode.Outdoors: Tapping the C-me button will activate the Follow Memode. Hover the drone at the height and distance desired before tapping the C-me button. The drone will maintain that altitude and distance from the phone while the pilot is walking at a normal pace. While in the Follow Me Mode, holding the Directional Control all the way to the left or right will make the C-me slowly circle the phone. Keep the phone still while in this mode.Tap the C-me button again to the exit the Find Me/Follow Me Mode.SETUPCharge the BatteryThe charge time will beapproximately 1 hour and 40 minutes.The C-me must be off while charging.Linking the C-me and the C-me AppPower on the C-me by pressingbutton until it lights up.Open the Wi-Fi settings on your phone and verify that the C-me network is selected. The default password is 12345678.To make sure that there will be no interruptions while running the C-me app, close any other apps that may be open. OPENThe phone will have a live image from the camera when it is linked to the C-me.NOTE: It make take up to 10 seconds to connect.
PREPARING TO FLYPlease review the Basic Operation animation in the Settings/Helpsection of the settings menu if you are not familiar with  ying the C-me.Flight ModesThe C-me will automatically be in the Indoor Mode when inside or when less than 6 satellite signals are being received while outside.When 6 or more satellite signals are received and the Indoor Mode Setting is “off”, the C-me will switch to the Outdoor Mode.The Indoor Mode can also be turned on with the button in Settings/Indoor Mode.CalibrationThe C-me compass and accelerometers should be calibrated the  rst time the C-me is  own and:1. Every time it is  own outside at a different location.2. Any time the motors are shutdown by the overload protection circuit.3. Hard landing or crash.Follow the animation to rotate hoizontally, then vertically. Rotate slowly and steadily for best results.IMPORTANT!Place on level surface.
FLYINGTIP: The C-me will perform best when the winds are below 3 mph (5 km/H).TakeoffNOTE: The LED will  ash when C-me has acquired 6 or more GPS satellite signals and is in the Outdoor Mode”Full chargeHold until theTake Off buttonis greenTap to takeoffThe C-me will immediately climb to about 1 meter indoors and up to 2 meters outdoors.TIP: If the Take Off button is not tapped within 5 seconds, it will lock. Hold the lock button again to unlock.Motor Overload ProtectionWhen the C-me has a hard landing, crashes into a solid object or if the propellers get stuck and cannot spin, the motors will turn off to protect the control board. The C-me will have to be turned off and back on again any time this happens. Both calibration procedures should be run before the C-me is  own again.TrimmingThe trim control buttons below and to the right of the Directional Control should be used when C-me constantly drifts in the same direction. After the C-me takes off in calm conditions, let it sit for a moment to see of it is stable. If it drifts in one direction, use the opposite trim button to correct it. For example, if the drone drifts to the left, the right trim button below the Directional Control should be tapped until the drone stops drifting in that direction.FlightPractice indoors before  ying outside because the controls are more sensitive when in the Outdoor Mode. To guide the C-me to a new position, use short movements with the Directional Control in the desired direction. Holding the control for more than a second in one direction will usually require movement in the opposite direction because the C-me will have  own past the desired position.Please keep in mind that the Directional Controls use the front of the C-me as reference. If the drone is pointed to the right and the Directional Control is moved forward, the drone will  y to the right.When the  ight is completed, always turn off the power and recharge the battery before the C-me is put away. On level surfacewith LED steadyTap to land
PHOTO/VIDEOCamera SettingsWhite Balance (the default setting is automatic white balance.) The settings for lighting conditions can also be selected (Sunshine, Clouds. Night, Indoors, and Candlelight).The Exposure, Contrast, and Brightness can be increased or decreased as needed.NOTE: These settings will not change when the app is closed and opened again.Factory Reset will set the White Balance to automatic and center the other adjustments.Still PhotosTap the Camera button to take a single photo. The image will be stored in the Photo Gallery on the phone and on an optional memory card that can be loaded on the C-me.Hold the camera button for 2 seconds to put the Self-timer and Burst Mode buttons on the screen.The Self-Timer has 3 second and 10 second timer options. Tap the number to start the timer.The Burst Mode has options for taking 3, 5, 10 or 15 photos at the rate of 2 photos per second. Tap the desired number to start the camera.Tap the camera button to remove the Self-timer and Burst Mode buttons from the screen.VideoTap the Video button to start recording a video which will be stored in the phone’s Photo Gallery and also on the optional memory card. A timer and Stop button will appear when the video starts. Tap on the Stop button to end the video.TIP: The video camera works best when the C-me is not moving. Do not start a video until the C-me is hovering at the desired height and distance from you.Memory Card Not included.
REPLACEMENT PARTS1. Propeller Set Black (4)2. Arm Set Front A1/B1 (2)3. Propeller Shaft Bearings 1.5x4x2mm (4) 4. Crown Gear 22T w/Shaft Set (2)5. A/B Motor Set with 8T Pinion (2)HCAE6001HCAE6070HCAE6055 HCAE6050HCAE6040Not Pictured:Propeller Guard Set Black (4) AC to USB Adapter, 5VDC, 2A, AC 120-240V USB/Micro Charge Cord, 1M Arm Set Rear A2/B2 (2)Replacement Parts:HCAE6002 HCAE6010 HCAE6011 HCAE60711453322TROUBLESHOOTINGPROBLEM: The C-me App will not connect to the droneSOLUTION: (1) Completely close the C-me app.(2) Open the Wi-Fi setting for the phone and select the C-me network if not already connected. (3) Open the C-me app.PROBLEM: I cannot remember the Wi-Fi password.SOLUTION: The default password is 12345678. If the password has been changed, reset the setting on the C-me to restore the default Wi- Fi name and password.PROBLEM: The C-me circles instead of hovering when outside.SOLUTION: The compass on the C-me should be calibrated. Please follow the procedure in the Calibration section of SettingsPROBLEM: The C-me is very noisy.SOLUTION: The propeller and/or propeller shaft needs to be replaced.PROBLEM: The C-me is drifting.SOLUTION: (1) Winds are above 3mph (5kmph) (2) The accelerometers on the C-me need to be calibrated. Please follow the procedure in the Calibration section of SettingsPROBLEM: The C-me is hard to control when outside.SOLUTION: (1) The Indoor Mode setting is turned on in Settings. (2) The C-me is not receiving 6 or more satellite signals. (3) The wind is above 5 mph (8kmph)
MAINTENANCEPropeller InstallationBe sure to match the letter on the propeller with the letter on the arm.Motor/Gear/Bearing ReplacementThe Motor, Gear, and Bearings can be replaced without removing the arm from the C-me. When installing a new gear or motor, place some lubricant from the old gear on the teeth of the new part.Arm Replacement1. Remove the parts from the damaged arm.2. Remove the 4 large screws from the frame below each arm.3. Carefully separate the cover from the frame enough to allow the arm to be removed.4. Remove the motor wire from the slot in the damaged arm.5. Remove the damaged arm from the frame.6. Install the new arm and reverse these steps.FCC IC PRECAUTIONSIC RSS WARNINGThis device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.IC RADIATION EXPOSURE STATEMENTThis equipment complies with IC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body.FCC RADIATION EXPOSURE STATEMENTThis equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.CE COMPLIANCE INFORMATION FOR THE EUROPEAN UNIONInstructions for Disposal of Waste Equipment by Private Users in the European Union:This symbol on the product or its packaging indicates this product must not be disposed of with other household waste. Instead, it is the user’s responsibility to dispose of their waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city of ce, your household waste disposal service or location where you purchased the product.
Item number: HCAE10Declaration of Conformity:Product: Hobbico C-me Camera Drone FCC ID: IYFCMEEquipment class: 1C-me Camera Drone: The objects of the declaration described here are in conformity with the requirements of the speci cations listed below, following the provisions of the European 2006/95/EC Low Voltage Directive:EN 60950-1:2013 SafetyThe objects of the declaration described here are in conformity with the requirements of the speci cations listed below, following the provisions of the European R&TTE directive 1999/5/EC:EN300 328 V1.9.1.Technical requirements for radio equipmentETSI EN 301 489-1 V1.9.1, 301 489-17 V2.2.1 General EMC requirements for radio equipmentHobbico, Inc.2904 Research RoadChampaign, IL USA 61826The associated regulatory agencies of the following countries recognize the noted certi cations to this product as authorized for sale and use.UK DE DK BG SE FI GREE LV LT PL CZ SK HURO SI AT IT ES PT IENL LU MT CYIC: 11104A-CMESTATEMENTS: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired changes or modi cations not expressly approved by the party responsible for compliance and could void the user’s authority to operate the equipment.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:● Reorient or relocate the receiving antenna.● Increase the separation between the equipment and receiver.● Co nnect the equipment into an outlet on a circuit different from that to which the receiver is connected.Consult the dealer or an experienced radio/TV technician for help.The FCC ID number is: IYFCME.
Cet appareil est conforme aux limitesd'exposition de rayonnement RF ISEDC établiespour un environnement non contr?lé. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. ISEDC Radiation Exposure Statement:This equipment complies with ISEDC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.This equipment should be installed and operated with minimum distance 20cm between the radiator& your body.Cetémetteur ne doit pas être co-implanté oufonctionner en conjonction avec toute autreantenne ou transmetteurCet équipement doit être installé et utiliséavec une distance minimale de 20cm entre leradiateur & votre corps.FCC Radiation Exposure Statement:

Navigation menu