Hobie Stripping Apron Users Manual

Stripping Apron to the manual 96695d78-5e38-4870-af78-655f241c8a47

: Hobie Hobie-Stripping-Apron-Users-Manual-565328 hobie-stripping-apron-users-manual-565328 hobie pdf

Open the PDF directly: View PDF .
Page Count: 5

FLOAT CAT

STRIPPING APRON

ASSEMBLY AND OPERATIONS MANUAL

Hobie Float Cat

Stripping Apron Assembly

(SEE ALSO: Large Diagrams Pg. 4)

Stripping Apron Parts List

Frame Rods:

J-1 fiberglass rod with hinge and ferrule

J-2 fiberglass rod with hinge and plain tip

Apron:

K-1 nylon storage bag with plastic hook and mesh

K-2 nylon storage bag with D ring

L two 7” aluminum apron support posts with molded

plastic C clamps

Hardware:

M four clevis pins with split rings

N two washers

O two eyebolts with nuts

P two Phillips head screws

Q two metal apron clips

Required tools: One large slot head screwdriver, one medium Phillips head screw driver

NOTE: Right and left references assumes a seated position facing aft.

Stripping Apron Assembly Instructions

STEP 1- Insert eyebolts (O) from outside seatback, through white

nylon bushings located on either side of seatback. Secure each with nuts. Eyebolts will spin freely in bushings.

STEP 2- Locate K1 and K2 and separate by undoing all Velcro edges and unhooking black plastic

hook on K1 from D ring on K2.

STEP 3- With Velcro edges completely unattached and bag facing zipper up, grasp K1 by grommeted tab and insert

ferrule end of J1 into the webbing sleeve along the curved edge of K1, bending rod as needed. Slide rod through sleeve

until grommeted tab can be inserted into hinge and lined up with the first hole (hole A) of hinge. Secure with clevis pin

and split ring. Repeat procedure with K2 and J2.

J1

K1

J2

K2

2

(SEE ALSO: Large Diagrams Pg. 4)

STEP 4- Grasp K1 with zipper facing up and insert eyebolt on left side

of seatback into hinge and align with hole B. Secure eyebolt to hinge

with clevis pin and split ring. Repeat procedure with K2, securing hinge to

eyebolt on right side of seatback with clevis pin and split ring.

STEP 5- Seated between apron rods J1 and J2 and with Velcro

separated, pull webbing sleeves back along each rod enough to expose the

ends. Grasp exposed rods near ends, pull the rods towards you, and insert

J2 into the J1 connecting ferrule as far as it will go.

STEP 6- Remain seated. Reach back to the hinge on each side of the

seatback. Wrap your fingers around the webbing sleeve next to each hinge.

Slide your hands along the webbing, gently stretching the webbing back over

the rods. Locate the connecting hook on K1 and the D ring on K2. Insert

hook into D ring. This is a tight fit. Pull mesh over lap and attach all Velcro

edges. If edges do not line up satisfactorily, separate edges and remove hook from D ring. Slide hook down it’s

attachment cords as far as possible. Untie stop knots in cords and retie further down. This shortens the hook connector

lead. Reconnect the hook onto the D ring. Pull mesh back into position and test Velcro alignment. When satisfactory,

separate Velcro edges, flip entire assembly over the head (much like a child’s highchair), and exit the Float Cat.

STEP 7- Locate L, P, and Q. Using a large flat head screwdriver, spread the open end of clip (Q) approximately 1/4”

further open. Locate grommet near edge of one storage bag. Install clip over edge, aligning hole in clip over grommet

and snapping into place. Repeat for other side.

STEP 8- Insert tapped end of apron support post up through webbing tab on side of storage bag. Place washer over

exposed screw threads and thread support post onto screw. Align opening in C clamp (on bottom of support post)

parallel with crossbar and tighten screw with screwdriver. Snap C clamps onto crossbars where they are exposed in

the troughs on top of pontoons.

STEP 9- Apron support posts can be easily released by angling to the left or right and pulling up.

HINGE PLACEMENT

3

4

For Your Information:

Date Purchased: ___________________

Store Purchased: ___________________

Retain for your records

Hobie Cat

4925 Oceanside Blvd., Oceanside, CA 92056

Tel: (760) 758-9100 Fax: (760) 758-1841

SAFETY PRECAUTIONS

• Always wear a US. Coast Guard Approved Floatation Device. As with canoes and kayaks, there is a danger of falling

over board. Always keep your weight centered. Flotation devices are mandatory for your safety.

• Your Float Cat was designed for Class 1 water or less. It was not designed for rough water, rapids, or high wind

conditions. Always use common sense and take weather, wind and water conditions into account before using your

Float Cat.

• Use common sense when using waders. Always wear a wader safety belt to keep water from entering your waders in

case you need to get off your boat or you end up in the water.

• Always attach the supplied tether to yourself so you will never get separated from your boat.

Warranty

Hobie Outback warranties it’s Float Cat products to be free of all defects in material and workmanship for

the period of Three years from date of purchase. Upon receipt and inspection Hobie Outback will repair or

replace at no charge any boats returned during the warranty period that are found defective. Please do not

return the product without our prior authorization. If necessary repairs are covered by warranty, we will pay

return shipping charges to any destination within the United States and Canada.

For the warranty to be effective, warranty card must be mailed with a copy of sales receipt. None of the

exclusions may apply. All factory repairs after the three year warranty period carry a 90 Day Limited Warranty

subject to exclusions and limitations as listed.

To enforce warranty or obtain repairs after limited warranty period, please contact us at (760) 758-9100

or by Fax at (760) 758-1841, and we will instruct you to either return the product to the company or

how we can replace parts as needed. You must at your expense include postage, shipping charges, and

insurance costs.

Warranty Exclusions

This warranty does not apply under the following circumstances:

• If the product has been serviced or repaired by anyone other than an authorized Hobie Dealer.

• If the product has been altered, adjusted or handled in a manner other than according to the Owners

Manual furnished with this product.

• If any defect, problem, loss or damage has resulted from any accident, misuse, negligence, or carelessness.

• If color fading or damage has taken place due to excess exposure to the sun.

We reserve the right to make changes or improvements in our product from time to time without incurring the

obligation to install such improvements or changes on equipment previously manufactured.

SALT WATER USERS

Remove and discard crossbar endcaps. Flush crossbars and rinse entire float cat after each use with fresh water.

Keep snap buttons protected with a lubricant such as WD-40TM

5