Hobie V2 Drum Users Manual Assembly
V2 Drum V2drum_assembly
v2drum b1aacc04-45df-414d-973f-1bf66f0be19a Hobie Boating Equipment V2 Drum User Guide |
2015-02-09
: Hobie Hobie-V2-Drum-Users-Manual-565326 hobie-v2-drum-users-manual-565326 hobie pdf
Open the PDF directly: View PDF 
.
Page Count: 4
| Download | |
| Open PDF In Browser | View PDF |
1 Assembling the new Mirage Drive drums and cables Caution: The new cables and drums are slotted for easier maintenance and tune ups. They are not interchangeable with the older parts. Warning: If cables are installed incorrectly, they may twist off the drums, causing the Drive to fail. Tip: DO NOT REUSE Nyloc nuts when installing new cables. The slotted cable threads have 40% less area -- worn Nylocs may back out causing Drive failure or adjustment problems. Tools and materials required: 7/16 inch wrench needle nose pliers Marine grade axle grease Preparation: 1. Remove old drums, cables and chains 2. Wipe drum axle clean 3. Pre-install crank arms to the drums, noting left and right crank arms Installation: 1. Install new chains / cables on sprockets, taking care to press chain solidly into master cog (Plastic sprockets only). This may be accomplished with the masts and fins on or off. Verify that chain is properly centered. (Tip: mark center 2 link of chain with marking pen for easy placement). 2. Lightly grease drum axle Note: there are two methods of assembling the cables to the new drums -- on the bench (3 through 7 "A" below) or with the drive properly mounted in a bench vise (3 through 7 "B" below). Each is described separately. Use which ever is easiest for you. Bench method: 3 A. Mount left or right drum / crank arm assembly (noting correct side) onto drum shaft 4 A. Install front and rear cable into upper drum slots as shown. It is easiest to angle cable in from the side (below and right). 5A. Slip cables over top lip and hand tighten new Nyloc nuts to keep cable from slipping out (right). 6A. Insert idler cable into rear slot as shown. Note -- this slot is divided -- use outboard portion of slot (left). 7A. Flip drive over and repeat on other side. 3 Vise method: 3 B. Secure Drive to vise by rear portion as shown. Use a rag in vise to prevent marks (rag removed for illustration purposes, right). 4 B. Mount both drum / crank arm assemblies to drum shaft, noting correct left and right side. 5 B. Mount the rear sprocket cable. Note, the cable is first inserted from the side, with the help of needle nose pliers if necessary, then re-routed over the top lip of the drum. Hand thread Nyloc nuts enough to keep the cable from slipping out (below). 6 B. Repeat procedure with the front sprocket cable. 7 B. Insert idler cable into lower rear drum hole as shown. Note, the idler slot is divided -- use the outboard portion only (right). 4 8. (both methods) Tighten and tune all cables. Make sure they are running properly on the drums (below). Align and center fins as necessary. Troubleshooting: 1. Cable wanders off drum. Cable is twisted. Remount, removing twist or warping cable toward inboard side of drum. 2. Cable appears to be uneven. Recheck center link of chain is mounted on center cog. Make sure chain is fully pressed in, particularly the center cog.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : MM Create Date : 2009:06:16 12:42:13-07:00 Modify Date : 2009:06:16 12:42:13-07:00 XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Creator Tool : PScript5.dll Version 5.2.2 Producer : Acrobat Distiller 9.0.0 (Windows) Format : application/pdf Title : Microsoft Word - Hobie drum assembly.doc Creator : MM Document ID : uuid:2297962b-3f42-40fe-92ad-206aaf4d905b Instance ID : uuid:16e16146-87c9-4e65-89cf-cb770f62caec Page Count : 4EXIF Metadata provided by EXIF.tools