Holzberg Communications KY105 Portable 2-way radio User Manual Ky105 405 Use s Manual

Download:
Mirror Download [FCC.gov]
Document ID	337793
Application ID	7dz8iL72uimzVez8gazz6g==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	10.79kB (134881 bits)
Date Submitted	2003-07-07 00:00:00
Date Available	2004-01-20 00:00:00
Creation Date	2002-04-12 11:05:46
Producing Software	Acrobat Distiller 4.05 for Windows
Document Lastmod	2002-04-12 11:06:16
Document Title	Ky105/405 Use's Manual
Document Creator	Microsoft Word 8.0
Document Author:	gds

Kyosey
Ky105/405 Portable Transceiver
User’s Manual
Ky105/405 Quick Reference
Channel Selector
Power/Volume Knob
PTT Button
Status LED
Microphone
Side Button 1
Side Button 2
SHORT:
LONG:
SHORT:
LONG:
Note: Fill in blank with the Button’s Function
Turning Power On
Turning Power Off
Rotate the Power/Volume Knob clockwise to turn on the
Rotate the Power/Volume Knob anti-clockwise until a click
transceiver. If the LED Indicator light GREEN to RED then
is hears to turn the transceiver off.
OFF, and a high voice beep means that the transceiver is ok,
otherwise, a low long beep means that Self-Tests failure.
Adjusting Volume
1.
If there is no receive audio, you need hold down the
Ky105/405 Quick Reference
2.
3.
Monitor button to open the squelch, so you can hear
1.
Turn on power.
background noise.
2.
Adjust the volume
Continue to hold the Monitor Button and rotary the
3.
Select a desired channel
Power/Volume Knob to desired volume level, turn
4.
When a signal with proper or matching sub-tones is
clockwise to increase or anti-clockwise to reduce the
received, you will hear the transmissions from other
volume.
transceivers. You may need to adjust the volume more
Release the Monitor Button.
precisely.
To Select a Channel
Rotate the Channel Selector Knob to select the channel
Deleting Nuisance Channel
1.
SCAN Mode, press the “Nuisance Delete” Button until
number.
To Transmit
1.
2.
While transceiver locked onto unwanted channel in the
you hear two beeps.
Rotate the Channel Selector Knob to select a desired
2.
channel.
Note:
Release the “Nuisance Delete” Button.
Press and hold down PTT button, hold the transceiver
“Nuisance Delete” can only be used if your dealer has
about 2.5 ~ 5cm (1 to 2 inches) from your lips to
programmed one function button for it.
microphone and speak in your normal speaking voice.
3.
Release the PTT button to return to the receive mode.
To Receive
Ky105/405 Quick Reference
LED Indicator
LED indicate / color
Explain
Light “RED” continuously
Transmitting a message
Receiving a signal
Light “GREEN” continuously
“GREEN” flash
Scanning
Light “ORANGE” continuously
A sub-tone code is received that is matching the code
programmed in your radio. The code may be a CTCSS
code or DCS code.
Beep for Side Button Operating
Button Function
Positive Beep
Negative Beep
Scan
Scan ON
Scan OFF
Power
High Power
Low Power
Squelch
Tight squelch
Normal squelch
Repeater/Talk-around
Without using a repeater
Using a repeater
CONTENTS
INTRODUCTION
TRANSCEIVER DETAILS
LED INDICATOR
PROGRAMMABLE BUTTON
BEEPS
GETTING STARTS
BATTERY INFORMATION
INSTALLING BATTERY PACK
REMOVAL OF BATTERY
INSTALLING THE ANTENNA
REMOVING THE ANTENNA
ATTACHING THE BELT CLIP
REMOVING THE BELT CLIP
BASIC OPERATION
SWITCHING POWER ON/OFF
ADJUSTING THE VOLUME
SELECTING A CHANNEL
TRANSMITTING A MESSAGE
RECEIVING A MESSAGE
CONTENTS
ADVANCED OPERATION
REPEATER/TALK-AROUND
SETTING SQUELCH LEVEL FOR TIGHT OR NORMAL
SELECTING OUTPUT POWER
HANDSFREE TRANSMISSION (VOX)
SCAN
SCAN MODEL
SCAN OPERATION
TALKBACK
DELETE A NUISANCE CHANNEL
TO RESTORE THE DELETED CHANNEL TO THE SCAN LIST
PRIORITY FUNCTION
Introduction
TRANSCEIVER DETAILS
①Channel Selector Knob
Selects operating channels.
② Power/Volume Knob
Switches the transceiver ON or OFF. Also increases or decreases the transceiver volume.
Introduction
③ LED Indicator
Indicate radio’s status
Explain
LED indicate / color
Light “RED” continuously
Transmitting a message
Light “GREEN” continuously
Receiving a signal
“GREEN” flash
Light “ORANGE” continuously
Scanning
A matching sub-tones code is received. It can be a
CTCSS code or DCS code.
④ Microphone
Hold radio upright while speaking clearly into the microphone.
⑤ PTT (Push-to-Talk) Button
This button is used to switch between transmission and reception. To transmit, hold in this button. To receive, just release this
button.
⑥ Side Button 1 (Programmable)
⑦ Side Button 2 (Programmable)
There are two Side Button in your radio and they can be programmed with different function by your dealer.
Please contact your dealer to know what function programmed for your side button.
Introduction
Press the side button as one of three methods of operation:
SHORT means click the button then release it, or
LONG means press the button for the long time then release it, your dealer may programmed the long time different, or
HOLD down the button, while you need check the status of radio or adjust the radio’s parameter, just hold down the button.
You may operate the side button as SHORT or LONG to activate one of its functions, but not two for once pressing.
Button Function
SHORT/LONG
Monitor
To starts scanning from current
channel or quit scanning
When radio is scanning, you can
Nuisance Delete
temporary remove the unwanted
channel from the scan list.
The
output
power is toggled between
Power
low and high.
Using a repeater or allow
Repeater/Talk-around
communication direct with other
transceivers without using a repeater.
To toggle the squelch level between
Squelch
normal and tight.
⑧ Accessory Connector Cap
Scan
HOLD
Monitor activity on your
selected channel
Introduction
BEEP
1.
Power ON Self Tests Success Beep
2.
Power ON Self Tests Failure Beep
3.
VOX Power ON Beep ( High Sensitivity )
4.
VOX Power ON Beep ( Low Sensitivity )
5.
Positive Beep
6.
Negative Beep
Note:
Mark means high voice beep.
Mark means low voice beep
10
Introduction
Beep for Side Button
Some beeps of the programmed Side Button are exchangeable, it means the function are exchangeable.
Side Button Function
Positive Beep
Negative Beep
Scan
Start scanning
Quit scan mode
Power
High output power
Low output power
Squelch
Tight squelch
Normal squelch
Repeater/Talk-around
Without using a repeater
Using a repeater
BATTERY INFORMATION
FOR LONGEST BATTERY LIFE AND USING KNACKS
Three types rechargeable batteries can be used as the supply power, Nickel Cadmium (Ni-Cd), Nickel Metal Hydride (Ni-MH) and
Lithium Ion (Li-ion).
To assure the highest performance and longest cycle life, should you properly use the battery pack comply with following simple
rules:
To enable you to obtain maximum battery capacity, a new battery must be fully charged for at least 14 to 16 hours
continuously.
Using a non- Kyosey brand charger may damage your battery, also will expire its warrant.
You can charge the battery that is connected to a transceiver, but please turn the radio off to fully charge it.
If possible, store and charge the battery at a room temperature (25℃). Do not charge a cold battery that is at 10℃ or
11
Getting Started
below, if so may cause the battery to leak and become an inefficacious battery.
Don’t charge a hot battery that is at above 35℃. This will decrease cycle life.
Note: The Kyosey brand Quick Charger built-in a temperature sensor to ensure your battery charged within above
temperature range.
New batteries can be stored up to two years without significant cycle loss. Store new / unused batteries at room
temperature in a cool, dry area.
A battery that has been in storage should be recharged at least 14 to 16 hours continuously before being put into
service.
Don’t return fully charged batteries to the charger for an "extra boost." This will significantly reduce cycle life.
Don’t leave your transceiver and battery in the charger when not charging. Continuous charging will shorten battery life
(Don't use your charger as a transceiver stand).
For optimum battery life and operation, use Kyosey brand chargers only. Our batteries and chargers have been
designed to operate as an integrated energy system.
12
Getting Started
INSTALLING BATTERY PACK
1.
Put the battery pack onto the bottom of the transceiver.
2.
Gently push the battery pack toward the transceiver back edge until you hear a
click.
REMOVAL OF BATTERY
1.
Before removing the battery, you must
turn the radio off.
2.
Press down the battery release button
located in the back of the battery pack.
3.
Remove the upside of the battery pack
separate from the transceiver body and
take away then.
13
Getting Started
INSTALLING THE ANTENNA
Fasten the antenna to the radio by placing the threaded end of the antenna into the
antenna connector. Rotate the antenna clockwise until tight.
EMOVING THE ANTENNA
Turn
the
antenna
in
an
anti-clockwise
direction until it disengages from the transceiver.
14
Getting Started
ATTACHING THE BELT CLIP
1.
Align mounting rails of the radio with the grooves of belt clip.
2.
Slide the belt clip downwards until it clicks into place.
REMOVING THE BELT CLIP
1.
Insert the end of a key to push the
release tab of radio away.
2.
Slide the belt clip upwards.
15
Getting Started
WITCHING POWER ON/OFF
To switch ON your transceiver, rotate the Power/Volume Knob clockwise. If the transceiver works proper, LED Indicator
will light GREEN, then RED and finally OFF, and you can hear the Self-Tests success beep, otherwise the Self-Tests failure
beep may be heard.
To switch OFF the transceiver, turn the Power/Volume Knob fully anti-clockwise until a “click” is heard.
ADJUSTING THE VOLUME
16
Basic Operations
If there is no receive audio, you need hold down the Monitor button to open the squelch, so you can hear background noise.
Continue to hold the Monitor Button and rotary the Power/Volume Knob to desired volume level, turn clockwise to increase
or anti-clockwise to reduce the volume.
Release the Monitor Button.
SELECTING A CHANNEL
The 16-channel provide for regular operating channel. Use the Channel Selector Knob to choose your desired channel.
You should not select a channel unless it is programmed in the transceiver. Your dealer can best explain how channel had
programmed.
Rotate the Channel Selector Knob to select your desired channel number.
TRANSMITTING A MESSAGE
1.
Turn ON your transceiver.
2.
Rotate the Channel Selector Knob to select a desired channel.
3.
Press and hold down PTT, hold the transceiver about 2.5 ~ 5cm (1 to 2 inches) from your lips to microphone and speak in
your normal speaking voice.
4.
Release the PTT button to return to the receive mode.
17
Basic Operations
RECEIVING A MESSAGE
1.
Turn your transceiver ON.
2.
Adjust the volume
3.
Select a desired channel
4.
When a signal with proper or matching sub-tones is received, you will hear the transmissions from other transceivers; you
may need to adjust the volume more precisely.
18
Advanced Operations
REPEATER/TALK-AROUND
At following condition, the Talk-around function will make you can talk directly to other transceiver without using a repeater:
If the repeater is deactivate, or
You are out of the repeater range, but you can directly talk to other transceiver.
To toggle Talk-around ON or OFF, your dealer must program a Side Button for the “Repeater/Talk-around” function.
Pressing the Repeater/Talk-around button, if you hear the Positive Beep, your transceiver is without using a repeater.
Others, for the Negative Beep, your transceiver is using a repeater.
SETTING SQUELCH LEVEL
Squelch acts as a kind of filtering system, which control the amount of signals the transceiver receives. Setting the
transceiver to the Tight Squelch, you can avoid some unwanted signals or noise. But you may not receive a weak signal far from
you. So you should select the Normal Squelch for it.
Pressing the Squelch button to select the squelch level between Tight and Normal.
The Positive Beep means your transceiver is Normal Squelch.
The Negative Beep means your transceiver is Tight Squelch.
SELECTING OUTPUT POWER
Each channel independently programmed for either low power or high output power. However, you can change the output
power by yourself.
With high output power, your signal may transmit farther.
Selecting low power conserves the battery if you can reliably communicate with others.
19
Advanced Operations
Each time you pressing the Power Button, the output power is toggle between LOW and HIGH.
The Positive Beep means output power is HIGH.
The Negative Beep means output power is LOW.
HANDSFREE TRANSMISSION (VOX)
VOX (Voice Operated eXchange) is an automatic system witch allows you to automatically switch the transmission in hands
free mode just by speaking in the built-in microphone of a headset.
VOX OPERATIONS
To set your transceiver to VOX model, you have to:
1.
Turn OFF your radio, then
2.
Switch on the radio keeping pressed the Side Button 1.
3.
Connect the optional headset with built-in microphone to the microphone connector located on the transceiver’s side.
4.
Ensure that the headset’s built-in microphone is located close to the side of your mouth.
None: PTT button is disabled during VOX.
SELECTING VOX SENSITIVITY
To change the VOX sensitivity between low and high, you should
1.
Turn OFF your radio, then
2.
Switch on the radio keeping pressed the Side Button 2.
20
Advanced Operations
SCAN
Scan operation tells the radio to monitor a number of channels where are some activities. Your dealer can program more
than 16 channels on the scan list.
When scanning, the transceiver checks each channel for activity and only stops on a channel if a signal is present.
SCAN OPERATION
To toggle scan ON/OFF by using the Side Button which programmed for “SCAN”.
1.
Press the “SCAN” button to begin scanning.
2.
Press the “SCAN” button to stop scanning while the radio works at scan model.
Note: The LED Indicator flashes the GREEN when scanning.
TALKBACK
If the “Talkback” function is active, direct you can communicate with others who call you just before the scan resume time
finish. Your dealer may tell you more detail about this function.
DELETE A NUISANCE CHANNEL
When the transceiver scans to a channel that you do not wish to hear, you can temporarily remove the channel from the scan
list using the Nuisance Channel Delete feature.
21
Advanced Operations
While the transceiver locked onto unwanted channel, press the “Nuisance Delete” Button until you hear two beeps.
Note: If the priority function is active by your dealer, you cannot remove the priority channel from the scan list. The last
channel cannot delete from the scan list too.
Note: To add a deleted nuisance channel back into the scan list, you must restart the radio.
PRIORITY FUNCTION
The priority function would spend more time to monitor the priority channel during scanning. Your dealer can program the
priority function using the CPS software.
PRIORITY FUNCTION
SCAN SEQUENCE
Activity
ch1 ➠ ch2 ➠ ch3 ➠ ch4 … ch1
Inactivity
ch1 ➠ ch2 ➠ ch1 ➠ ch3 ➠ ch1 ➠ ch4 ➠ ch1
22

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Producer                        : Acrobat Distiller 4.05 for Windows
Creator                         : Microsoft Word 8.0
Modify Date                     : 2002:04:12 11:06:16+09:00
Author                          : gds
Title                           : Ky105/405 Use's Manual
Create Date                     : 2002:04:12 11:05:46
Page Count                      : 22
Page Mode                       : UseNone

EXIF Metadata provided by EXIF.tools