Home Star HOMESTAR-TEDBC Electric fireplace User Manual
Homestar Corporation Electric fireplace
User Manual
![](/img.php?id=3356359&img=bg1.png)
1-855-837-2569
bC
Scan the below QR code
to download Smart Flame.
![](/img.php?id=3356359&img=bg2.png)
20.When the mantel slide doors cover the firebox, the firebox
will be closed, if you move away the doors, the firebox will
restar to
work. Make sure the power is turned off when you are
not use the unit.
21. The firebox can be controlled with Bluetooth by Iphone and
Android mobile phone, please refer to the page E-5, E-6 for detailed
operation instructions.
22. SAVE THESE INSTRUCTIONS
and dust.
E-1
licensed
19.The heater has a safety device that makes it stop working
once the inner temperature reaches 85º (± 2°C). To reset the
appliance, turn heater off and disconnect power, let it cool off
for 10 minutes and plug back in.
tap (outlet/power strip).
fire, electric shock or injury to persons.
![](/img.php?id=3356359&img=bg3.png)
9.2 kg / 10.2 kg
23 1/8 x 7 x 17 5/8 inch
59 x 17.9 x 44.8 cm
E-2
This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
Any Changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority
to operate the equipment.
Note: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for
help.
This equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 20cm between
the radiator & your body.
![](/img.php?id=3356359&img=bg4.png)
Control
Panel
Indicators
When a function is changed from the control panel or remote there will be a corresponding indicator displayed. The indicator shows
the function changed and the level selected. When the function is turned off, the corresponding indicator will fade off.
E-3
OPERATING INSTRUCTIONS
Figure 2
Figure 3
![](/img.php?id=3356359&img=bg5.png)
E-4
OPERATING INSTRUCTIONS
FUNCTION ICON DESCRIPTION
This button will not only put the fireplace insert in a standby mode, but also you can
see the flame effect through the screen. This will turn off all functins at once.
Note: Holding the POWER button for 3 seconds will turn on the Child safety lock. It
disables or enables all functions on the control panel and remote control.
The fireplace contains a fan forced heater.
The default setting temperature is 72°F (22°C).
The thermostat setting range is 50°-86°F or 10°-30°C.
The thermostat is adjustable by 2°F or 1°C increments.
To change between °F and °C press and hold the HEATER button for 5 seconds.
Press the ECO button when the heater is on, to run the heater in a reduced wattage
range.
Note: Holding the ECO button for 3 seconds disables any heater functions.
To quickly heat up a cold room/space, press the BOOST button to run the heater at
the full rated wattage.
Pressing the BOOST button repeatedly will cycle through the following boost settings:
5 minutes, 10min, 15min, 20min, 25min, 30min and off.
Pressing the timer button repeatedly will cycle through the following timer settings:
30 minutes, 1 hr, 2 hr, 3 hr, 4 hr, 5 hr, 6 hr, 7 hr, 8 hr and off.
The fireplace will automatically turn off when the timer reaches zero minutes.
This button controls the brightness of the flame effect.
POWER
HEATER
ECO
BOOST
TIMER
BRIGHTNESS
![](/img.php?id=3356359&img=bg6.png)
E-5
OPERATING INSTRUCTIONS
Figure 4
Bluetooth Operation Instructions as below. Please make sure has been opened.
1. Scan the below QR code to download Smart Flame or search “Smart Flame” from Apple AP P
Store and Google Play Store to download.
2. Register an account with your cellphone number or email adress.
3. Log in and tap to scan the QR code again to bind the cellphone with the unit.
Then set any device name as you like.
4. There is notice “Add the device successfully”, that means you have added the unit successfully.
5. Tap the enter Home interface.
NOTICE: Due to some protecting reason, when you scan QR code via Wechat, click top
right to open in Safari or Brower.
![](/img.php?id=3356359&img=bg7.png)
E-6
OPERATING INSTRUCTIONS
FUNCTION ICON DESCRIPTION
This button will not only put the fireplace insert in a standby mode, but also you can
see the flame effect through the screen. This will turn off all functions at once.
Slide to set the tempereture. Tap the tempereture to change between °F and °C.
The default setting temperature is 72°F (22°C).
The thermostat setting range is 50°-86°F or 10°-30°C.
The thermostat is adjustable by 2°F or 1°C increments.
Press the ECO button when the heater is on, to run the heater in a reduced wattage
range.
Quickly heat up the room/space with tapping the BOOST button. This will push the
heater to full wattage and heat the room up faster.
Pressing the BOOST button repeatedly will cycle through the following boost settings:
5 minutes, 10min, 15min, 20min, 25min, 30min and off.
Slide the timer through the following timer settings:
30 minutes, 1 hr, 2 hr, 3 hr, 4 hr, 5 hr, 6 hr, 7 hr, 8 hr and off.
The fireplace will automatically turn off when the timer reaches zero minutes.
This button controls the brightness of the flame effect. There are 5 level brightness.
POWER
HEATER
ECO
BOOST
TIMER
BRIGHTNESS
BLUETOOTH Press this botton to connect the unit and also return back to the Device list interface.
CHILDREN LOCK
SETTING
INSTRUCTION
Press the botton, choose “Yes” to turn on the Child safty lock, it disables or
enables all functions on the control panel, remote control and cellphone
Press the botton to choose “English”, “French” and “Spanish”. Also find the
Customer service information.
To review the instruction manual tap the information icon.
Tap the tempereture gauge button open the HEAT function.
![](/img.php?id=3356359&img=bg8.png)
Display shows “E2”.
There is no power.
Power cord gets warm.
The remote control is
not working.
The noise when the heater
is on is louder than normal.
Abnormal noise when the
heater is not on and the
flame effect is on.
Display shows “E1”.
Inspect the heater and check that the air inlets and outlets are
not blocked as this may cause overheating. Unplug the heater
for 10 minutes and allow it to cool down. Plug back in and turn
it on; check the heater for signs of overheating. If the problem
persists discontinue use of the heater and contact customer
service.
Contact customer service for a replacement thermostat sensor.
Check that unit is plugged into a standard 120V outlet. Press the
power button several times and make sure the power is set to
the “ON” position.
Adjust the temperature settings to ensure that the thermostat is
set higher than the current room temperature.
Check your heater cord and plug connections. Faulty wall outlet
connections or loose plugs can cause the outlet or plug to
overheat. Be sure the plug fits tight in the outlet. Heaters draw
more current than small appliances, overheating of the outlet
may occur even if it has not occurred with the use of other
appliances. During use check frequently to determine if your
plug outlet or faceplate is HOT! If so, discontinue use of the
heater and have a qualified electrician check and/or replace the
faulty outlet(s).
Change the remote battery.
b. Contact Customer Service for a new heater/blower assembly.
Contact Customer Service for a new spinner motor.
E-7
TROUBLESHOOTING GUIDE
The heater does not blow
warm air.
Manual Reset overheat
protection has triggered.
The thermostat sensor is
broken or disconnected.
There is no power to the unit.
Thermostat setting is preventing
heater from turning on.
Normal operation.
There is no battery or the
signal is poor.
a. The air intakes are dirty or
obstructed.
b. The blower/heater assembly
is defective.
The spinner motor is defective.
a. Check the air intakes for obstructions or high dust build up.
Operate remote control at a slow measured pace.
Press the remote control buttons with an even motion and gentle
pressure. Repeatedly pressing buttons in rapid succession may
cause the transmitter to malfunction.
POSSIBLE CAUSEPROBLEM CORRECTIVE ACTION
![](/img.php?id=3356359&img=bg9.png)
E-8
REPLACING THE REMOTE
CONTROL BATTERY DISPOSING OF USED
BATTERIES
When the remote control stops operating or its range seems reduced,
Please operate the remote control at a slow measured pace. Press
the remote control buttons with an even motion and gentle pressure.
Repeatedly pressing buttons in rapid succession may cause the
transmitter to malfunction.
it is time to replace the battery with new ones.
Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad,
ni-mh, etc) batteries.
Battery should be removed if the product is to be left unused for a
long time.
The batteries may contain hazardous substances that could
endanger the enviroment and human health.
This symbol appearing on the battery and/or packaging
indicates that used batteries must not be processed with
municipal waste. Instead they should be brought to the
appropriate collection point for recycling.
By correctly disposing of used batteries, you prevent potential
negative consequences for the environment and human
health. Recycling used materials also preserves our natural
resources.
For more information about collecting and recycling used
batteries, please contact your local municipality, your waste
disposal service or the store where you purchased this product.
3 volt lithium coin cell type 2025.
NOTE:
Caution for Ingestion.
1 2
34
cleaning the appliance.
INSTRUCTIONS
![](/img.php?id=3356359&img=bga.png)
4
BIG LOTS
BIG LOTS.
yourself.
1-855-837-2569