Home Star HOMESTAR-TEDBC Electric fireplace User Manual

Homestar Corporation Electric fireplace

User Manual

1-855-837-2569bCScan the below QR codeto download Smart Flame.
20.When the mantel slide doors cover the firebox, the firebox will be closed, if you move away the doors, the firebox will restar to work. Make sure the power is turned off when you are not use the unit.21. The firebox can be controlled with Bluetooth by Iphone and Android mobile phone, please refer to the page E-5, E-6 for detailed operation instructions.22. SAVE THESE INSTRUCTIONSand dust.E-1licensed19.The heater has a safety device that makes it stop working once the inner temperature reaches 85º (± 2°C). To reset the appliance, turn heater off and disconnect power, let it cool off for 10 minutes and plug back in.tap (outlet/power strip).fire, electric shock or injury to persons.
9.2 kg / 10.2 kg23 1/8 x 7 x 17 5/8 inch59 x 17.9 x 44.8 cmE-2This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:-Reorient or relocate the receiving antenna.-Increase the separation between the equipment and receiver.-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.-Consult the dealer or an experienced radio/TV technician for help.This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Control PanelIndicatorsWhen a function is changed from the control panel or remote there will be a corresponding indicator displayed. The indicator shows the function changed and the level selected. When the function is turned off, the corresponding indicator will fade off. E-3OPERATING INSTRUCTIONSFigure 2Figure 3
E-4OPERATING INSTRUCTIONSFUNCTION ICON DESCRIPTIONThis button will not only put the fireplace insert in a standby mode, but also you can see the flame effect through the screen. This will turn off all functins at once.Note: Holding the POWER button for 3 seconds will turn on the Child safety lock. Itdisables or enables all functions on the control panel and remote control.The fireplace contains a fan forced heater.The default setting temperature is 72°F (22°C).The thermostat setting range is 50°-86°F or 10°-30°C.The thermostat is adjustable by 2°F or 1°C increments.To change between °F and °C press and hold the HEATER button for 5 seconds. Press the ECO button when the heater is on, to run the heater in a reduced wattage range.Note: Holding the ECO button for 3 seconds disables any heater functions.To quickly heat up a cold room/space, press the BOOST button to run the heater at the full rated wattage.Pressing the BOOST button repeatedly will cycle through the following boost settings: 5 minutes, 10min, 15min, 20min, 25min, 30min and off.Pressing the timer button repeatedly will cycle through the following timer settings: 30 minutes, 1 hr, 2 hr, 3 hr, 4 hr, 5 hr, 6 hr, 7 hr, 8 hr and off.The fireplace will automatically turn off when the timer reaches zero minutes.This button controls the brightness of the flame effect. POWERHEATERECOBOOSTTIMERBRIGHTNESS
E-5OPERATING INSTRUCTIONSFigure 4Bluetooth Operation Instructions as below. Please make sure has been opened.1. Scan the below QR code to download Smart Flame or search “Smart Flame” from Apple AP P Store and Google Play Store to download.2. Register an account with your cellphone number or email adress.3. Log in and tap to scan the QR code again to bind the cellphone with the unit. Then set any device name as you like.4. There is notice “Add the device successfully”, that means you have added the unit successfully.5. Tap the enter Home interface.NOTICE: Due to some protecting reason, when you scan QR code via Wechat, click topright to open in Safari or Brower.
E-6OPERATING INSTRUCTIONSFUNCTION ICON DESCRIPTIONThis button will not only put the fireplace insert in a standby mode, but also you can see the flame effect through the screen. This will turn off all functions at once.Slide to set the tempereture. Tap the tempereture to change between °F and °C.The default setting temperature is 72°F (22°C).The thermostat setting range is 50°-86°F or 10°-30°C.The thermostat is adjustable by 2°F or 1°C increments.Press the ECO button when the heater is on, to run the heater in a reduced wattage range.Quickly heat up the room/space with tapping the BOOST button. This will push the heater to full wattage and heat the room up faster. Pressing the BOOST button repeatedly will cycle through the following boost settings: 5 minutes, 10min, 15min, 20min, 25min, 30min and off.Slide the timer through the following timer settings: 30 minutes, 1 hr, 2 hr, 3 hr, 4 hr, 5 hr, 6 hr, 7 hr, 8 hr and off.The fireplace will automatically turn off when the timer reaches zero minutes.This button controls the brightness of the flame effect. There are 5 level brightness. POWERHEATERECOBOOSTTIMERBRIGHTNESSBLUETOOTH Press this botton to connect the unit and also return back to the Device list interface.CHILDREN LOCKSETTINGINSTRUCTIONPress the botton, choose “Yes” to turn on the Child safty lock, it disables or enables all functions on the control panel, remote control and cellphone Press the botton to choose “English”, “French” and “Spanish”. Also find the Customer service information.To review the instruction manual tap the information icon. Tap the tempereture gauge button open the HEAT function.
Display shows “E2”. There is no power. Power cord gets warm.The remote control is not working.The noise when the heater is on is louder than normal. Abnormal noise when the heater is not on and the flame effect is on.Display shows “E1”.Inspect the heater and check that the air inlets and outlets are not blocked as this may cause overheating. Unplug the heater for 10 minutes and allow it to cool down. Plug back in and turn it on; check the heater for signs of overheating. If the problem persists discontinue use of the heater and contact customer service.Contact customer service for a replacement thermostat sensor. Check that unit is plugged into a standard 120V outlet. Press the power button several times and make sure the power is set to the “ON” position.Adjust the temperature settings to ensure that the thermostat is set higher than the current room temperature.Check your heater cord and plug connections. Faulty wall outlet connections or loose plugs can cause the outlet or plug to overheat. Be sure the plug fits tight in the outlet. Heaters draw more current than small appliances, overheating of the outlet may occur even if it has not occurred with the use of other appliances. During use check frequently to determine if your plug outlet or faceplate is HOT! If so, discontinue use of the heater and have a qualified electrician check and/or replace the faulty outlet(s). Change the remote battery.b. Contact Customer Service for a new heater/blower assembly. Contact Customer Service for a new spinner motor. E-7TROUBLESHOOTING GUIDE The heater does not blow warm air.Manual Reset overheat protection has triggered.The thermostat sensor is broken or disconnected.There is no power to the unit.Thermostat setting is preventing heater from turning on.Normal operation.There is no battery or the signal is poor.a. The air intakes are dirty or obstructed.b. The blower/heater assembly is defective.The spinner motor is defective.a. Check the air intakes for obstructions or high dust build up.Operate remote control at a slow measured pace.Press the remote control buttons with an even motion and gentle pressure. Repeatedly pressing buttons in rapid succession may cause the transmitter to malfunction.POSSIBLE CAUSEPROBLEM CORRECTIVE ACTION
E-8REPLACING THE REMOTE CONTROL BATTERY DISPOSING OF USEDBATTERIESWhen the remote control stops operating or its range seems reduced, Please operate the remote control at a slow measured pace. Press the remote control buttons with an even motion and gentle pressure. Repeatedly pressing buttons in rapid succession may cause the transmitter to malfunction.it is time to replace the battery with new ones. Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh, etc) batteries.Battery should be removed if the product is to be left unused for a long time.The batteries may contain hazardous substances that could endanger the enviroment and human health. This symbol appearing on the battery and/or packaging indicates that used batteries must not be processed with municipal waste. Instead they should be brought to the appropriate collection point for recycling.By correctly disposing of used batteries, you prevent potential negative consequences for the environment and human health. Recycling used materials also preserves our natural resources. For more information about collecting and recycling used batteries, please contact your local municipality, your waste disposal service or the store where you purchased this product. 3 volt lithium coin cell type 2025.NOTE:Caution for Ingestion. 1 234cleaning the appliance. INSTRUCTIONS
4BIG LOTSBIG LOTS.yourself.1-855-837-2569

Navigation menu