Homewerks Worldwide 7130-02-BT ventilating bath fan with bluetooth speaker User Manual 1

Homewerks Worldwide, LLC ventilating bath fan with bluetooth speaker Users Manual 1

Contents

Users Manual-1

www.homewerksww.com  VENTILATING BATH FAN WITH BLUETOOTH®  SPEAKERMODEL #7130-02-BTEspañol p. 14Jan. 8, 2016Home NetWerksSIMPLE SOLUTIONS FOR A SMARTER HOME For installation video go to: https://www.youtube.com/watch?v=qTU28V-cjVYxQuestions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-877-319-3757, 8 a.m. - 5 p.m., CST, Monday - Friday.The BLUETOOTH® word mark and logos are registered trademarks owned by BLUETOOTH SIG, Inc. and any use of the said mark by Homewerks Worldwide is under license. Other trademark and trade names are those of their respective owners.READ AND SAVE THESE INSTRUCTIONS
2www.homewerksww.comTABLE OF CONTENTSPRODUCT SPECIFICATIONSSPECIFICATIONS SPECIFICATIONSAirow: 90CFM Motor power consumption: 34 W120V, 60Hz Exhaust fan speed: 782 RPMDuct diameter: 4 in. Weight: 11.7 lbs.Sound output: 1.5 SonesProduct Specications ........................................................................................................................2FCC Compliance ................................................................................................................................2Package Contents ..............................................................................................................................3Hardware Contents.............................................................................................................................3Safety Information ..............................................................................................................................4Preparation .........................................................................................................................................4New Construction Assembly Instructions ...........................................................................................6Existing Construction Assembly Instructions ......................................................................................7BLUETOOTH® Speaker Fan Grille Installation ................................................................................... 9Pairing Light Switch with Fan ...........................................................................................................10Pairing your BLUETOOTH® Device to the Speaker .........................................................................10BLUETOOTH® Speaker and Fan Operation .....................................................................................10Care and Maintenance ..................................................................................................................... 11Troubleshooting ................................................................................................................................ 13Warranty ...........................................................................................................................................13FCC COMPLIANCEThis equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modications or changes to this equipment. Such modications or changes could void the user’s authority to operate the equipment.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed andused in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.–  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.Changes or modications made to this equipment not expressly approved by Homewerks Worldwide, LLC may void the FCC authorization to operate this equipment.
3www.homewerksww.comHARDWARE CONTENTS (not actual size)AA BBLong Wood ScrewShort Machine ScrewQty. 8 Qty. 3PACKAGE CONTENTSAGBCEDNIGHT LIGHTPART DESCRIPTION QTYA Fan body 1BGrille w/BLUETOOTH® speakersand light 1C Suspension Bracket I 1PART DESCRIPTION QTYD Suspension bracket II 1E Suspension Bracket III 1G Wall switch 1
4www.homewerksww.comSAFETY INFORMATIONPlease read and understand this entire manual before attempting to assemble, operate or install  the product.1.  Always disconnect the power supply prior to servicing the fan, motor or junction box.2.  Installation work must be carried out by a qualied person(s) in accordance to all local and  safety codes including the rules for re-rated construction.3.  Follow all local building, safety and electrical codes as well as NEC (National Electrical Code) and OSHA (Occupational Safety and Health Act).4.  Electric Service supply must be 120 volts, 60 hertz.5.  This unit must be properly grounded.6.  Do not bend or kink the power wires.7.  Exercise care to not damage existing wiring when cutting or drilling into walls or ceilings.8.  Sufcient air supply is required for proper combustion and the exhaustion of gases through  the chimney (ue) of fuel burning equipment to prevent back-drafting. See the standards of  NFPA (National Fire Protection Association) and ASHRAE (American Society for Heating  Refrigeration and Air Conditioning Engineers) and the local building code authorities.9.  Do not use this fan with any solid state control device, such as a remote control, dimmer switch,  or certain timers. Mechanical timers are not solid state devices.10.  This ventilation fan is approved for use over a bathtub or shower when installed in a GFCI  protected circuit. Do not use fans over a bathtub or shower that are not approved for that  application and marked accordingly.11.  Do not install in a cooking area.12.  Do not use to exhaust hazardous or explosive vapors.13.  Fans should always be vented to the exterior and in compliance with local codes.14.  Do not install in a ceiling with insulation greater than R42.15.  Duct work should be installed in a straight line with minimal bends.16.  Duct work size must be the same size as the discharge and should not be reduced. Reducing  the duct size may increase fan noise.17.  Prior to service or cleaning this unit, shut off power supply at the panel and lock to  prevent the power from being turned on. If the panel cannot be locked, clearly mark  the panel with a warning tag to prevent the power from being turned on.18.  Use this unit in the manner intended by the manufacturer. If you have any questions. Please  call customer service.19.  The fan is intended to be mounted at least 7.6 ft. above the oor.PREPARATIONBefore beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents. If any part is missing or damaged, do not attempt to assemble the product. Contact customer service for replacement parts at 1-877-319-3757, 8 a.m. - 5 p.m., CST, Monday - Friday.
5www.homewerksww.comTools Required for Assembly (not included): Hammer, Flathead Screwdriver, Wire Nuts, Nails, Duct Tape,Phillips Head Screwdriver, Utility Knife or Drywall Saw,Helpful Tools (not included): Electric Drill, Drill BitsWARNING: Turn off electricity at breaker box before beginning installation.Carefully remove unit from carton.Check area above installation location to be sure that wiring can run to the planned location and that duct work can be run and the area is sufcient for proper ventilation.Inspect duct work and wiring before proceeding with installation.Before installation, provide inspection and future maintenance access at a location that will not interfere with installation work.You may need the help of a second person to install this fan; one person on the attic side and one on the room side.Note: Installations may vary depending on how the previous bath fan was installed. Supplies necessary  for the installation of your bath fan are not all included; however, most are available at your local home improvement or hardware store.DIMENSIONS REQUIREMENTSCeiling  Opening (L)Ceiling  Opening (W)Ceiling  Opening (H)Housing  Dimension (L)Housing  Dimension (W)Housing  Dimension (H)9.4 in. 9.4 in. 7.4 in. 9.25 in. 9.25 in. 7.3 in.WIRING DIAGRAMAll wiring must be connected for full functionality.PREPARATIONNIGHT LIGHTLIGHTFANMUSICneutral/whitepower/blackground wire/greenswitch/blackneutral/whiteswitch/redFanAC120V/60HzGreenRedWhiteBlack
6www.homewerksww.comASSEMBLY INSTRUCTIONSNEW CONSTRUCTION – ATTACHING TO THE JOIST BEFORE INSTALLATIONTurn off power source. Review all safety  precautions.1.  Insert suspension bracket onto fan housing using suspension bracket I (C) and II (D). If spacing between joists is 21.5 in. to 23.5 in. attach suspension bracket III (E).2.  Position fan housing so edge of fan is ush with sheetrock. Do not ush mount housing with joist.3.   Secure the fan housing to joist with suspension brackets using long wood screws (AA) (included). (Joist spacing of less than 21.25 in.)4.  Mounting with joist spacing of 21.25 in. to 23.5in.1CED4231 24
7www.homewerksww.comASSEMBLY INSTRUCTIONSWall switchback viewWhitewireBlackwireRedwireGreenwireWallswitchNIGHT LIGHT565.  Secure the suspension bracket I (C) to fan housing using short machine screw (BB) (included).6.  Remove junction box cover. As shown in wiring diagram on page 5, using quick connect ports connect house wires to switch and fan.7.  Connect a 4 in. circular duct and vent to the outside. Secure it with duct tape or clamp.  Turn on power source.EXISTING CONSTRUCTION – ACCESSIBLE FROM ABOVE BEFORE INSTALLATIONTurn off power source. Review all safety precautions.1. Remove existing fan.71
8www.homewerksww.comASSEMBLY INSTRUCTIONS2.  Measure the opening to assure it is large enough to accommodate the new fan housing (9.4 in. x 9.4 in.).3.  If this fan is not replacing an old fan be sure to cut a 9.4 in. x 9.4 in. opening for the fan housing.4.  Insert suspension bracket onto fan housing using suspension bracket I (C) and II (D). If spacing between joists is 21.5 in. to 23.5 in. attach suspension bracket III (E).5.  Position fan housing so edge of fan is ush with sheetrock. Do not ush mount housing with joist.6.  Secure the fan housing to joist with suspension brackets using long wood screws (AA) (included). (Joist spacing of less than 21.25 in.)2365CED49.4"9.4"456789101111 2

Navigation menu